tp-link KS200M Kasa Smart Wi-Fi Motion-Activated Light Switch User Guide

: June 5, 2024
: tp-link

Table of Contents

Wire Your Switch
Set Up Your Switch
Appearance
Button Explanations
LED Status
Specifications
Documents / Resources

KS200M Kasa Smart Wi-Fi Motion-Activated Light Switch
User Guide

*Images may differ from your actual product.

Wire Your Switch

Turn off the circuit breaker. Then remove the old wallplate of the wall switch and label the wires. Ground: Usually green or copper.
Neutral: Usually white, not connected to the dumb switch.
Line/Load: Usually black, and connected to the dumb switch.
If you are unsure, consult a qualified electrician.
Disconnect wires from the old switch.
Connect the wires to the smart switch as shown below. Note: No need to distinguish between Line and Load wires.
Line up the switch with the mounting holes. Secure it with screws.
Attach the wallplate. Then the wiring is finished.

Set Up Your Switch

STEP 1
DOWNLOAD APP
Get the Kasa Smart app from the App Store or Google Play. tp link KS200M Kasa
Smart Wi Fi Motion Activated Light Switch - Qr Code

http://www.tp-link.com/common/promos/app_kasa.html?ref=QRCode

STEP 2
SET UP
Tap the + button in the app and select Smart Switches. Then follow the step-by-step app instructions to set up your smart switch. tp link KS200M
Kasa Smart Wi Fi Motion Activated Light Switch - Fig 4

Appearance

The built-in motion and ambient light sensors work together to realize hands- free control. tp link KS200M Kasa Smart Wi Fi Motion Activated Light Switch -
Fig 3

Button Explanations

Reset| Press and hold for about 5s to reset Wi-Fi while keeping other settings.
Press and hold for about 10s to restore your switch to factory default settings.
---|---
Restart| Press to restart your switch.

LED Status

Flashing red	Starting up.
Flashing amber & green	Ready for setup.
Flashing green	Connecting to Wi-Fi.
Stay green for the 30s	Connected to Wi-Fi.
Solid red	Disconnected from Wi-Fi.
Flashing amber	Device resetting.
White	The light fixture is off.

Specifications

Rating: 120V~ 60Hz
Load: 600W Incandescent, 1/6 HP Motor
Operation temperature: 0~40 ℃
Method of mounting included: Independently mounted (Vertically position only);
Operating control, Type 1. C action
Pollution Degree 2, Rated Impulse Voltage 2500 V
Software Class A, NEMA Type 1
CAUTION
Before installing, servicing or removing the switch, read and follow all safety precautions including the following:

CAUTION – Risk of Electric Shock – More than one disconnect switch may be required to de-energize the equipment before servicing. A circuit breaker that disconnects the Line and Neutral conductor simultaneously is suitable. Ensure power is off at the circuit breaker before removing or installing any switch. Use a non-contact voltage tester to ensure the power is off.
The Smart Switch must be installed and used in accordance with the National Electric Code (NEC) or your local electrical code. If you are unfamiliar with these codes and requirements or are uncomfortable performing the installation, consult a qualified electrician.
Do not install the Smart Switch with wet hands or when standing on wet or damp surfaces.
Install only in a suitable UL Listed outlet box (suitable dimensions: H > 2.95 in./75 mm, W > 1.81 in./46 mm, D > 2 in./51 mm).

tp link KS200M Kasa Smart Wi Fi Motion Activated Light Switch - Fig
5 Need some help?
Visitwww.tp-link.com/support
for technical support, user guides, FAQs, warranty & more
7106509393 REV1.1.0 ©2022 TP-Link

Documents / Resources

| tp- link KS200M Kasa Smart Wi-Fi Motion-Activated Light Switch [pdf] User Guide
KS200M, Kasa Smart Wi-Fi Motion-Activated Light Switch, KS200M Kasa Smart Wi- Fi Motion-Activated Light Switch
---|---