IKEA 403.824.98 KULINARISK Kitchen Hood Instruction Manual

: June 5, 2024
: Ikea

Table of Contents

Safety information
Product description
Control Panel
General hints
Care and cleaning
What to do if…
Technical Data
Energy efficiency
Environment concerns
IKEA GUARANTEE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KEA 403.824.98 KULINARISK Kitchen Hood

Safety information

For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. The wire connection has to be done by a specialized technician.

The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
The minimum safety distance between the cooker top and the extractor hood is: for the electrical hob 500mm and for gas hob 650mm.
If the instructions for installation for the gas hob specify a greater distance, this must be respected.
Check that the mains voltage corresponds to that indicated on the rating plate fixed to the inside of the hood.
Means for disconnection must be incorporated in the fixed wiring in accordance with the wiring rules.
For Class I appliances, check that the domestic power supply guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of a minimum diameter 120 mm. The route of the flue must be as short as possible.
Do not connect the extractor hood to exhaust ducts carrying combustion fumes (boilers, fireplaces, etc.).
If the extractor is used in conjunction with non-electrical appliances (e.g. gas burning appliances), a sufficient degree of aeration must be guaranteed in the room in order to prevent the backflow of exhaust gas. When the cooker hood is used in conjunction with appliances supplied with energy other than electric, the negative pressure in the room must not exceed 0,04 mbar to prevent fumes from being drawn back into the room by the cooker hood.
The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels.
If the supply cord is damaged, it must be replaced from the manufacturer or its service agent.
Connect the plug to a socket complying with current regulations, located in an accessible place
With regards to the technical and safety measures to be adopted for fume discharging it is importat to closely follow the regulations provided by the local authorities.

WARNING: Before installing the Hood, remove the protective films.

Use only screws and small parts in support of the hood.

WARNING: Failure to install the screws or fixing device in accordance with these instructions may result in electrical hazards.

Connect the hood to the power net by using a bipolar switch having a contact gap of at least 3 mm.
Do not look directly at the light through optical devices (binoculars, magnifying glasses…).
Do not flambè under the range hood; risk of fire.
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Children should be supervised to ensure that they do not play with the appliance.
The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction Accessible parts may become hot when used with cooking appliances.
Clean and/or replace the Filters after the specified time period (Fire hazard).
There shall be adequate ventilation of the room when the range hood is used at the same time as appliances burning gas or other fuels (not applicable to appliances that only discharge the air back into the room)

Use

Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.
The top of the hood must not to be used as a shelf.
The extractor hood has been designed exclusively for domestic use to eliminate kitchen smells.
Never use the hood for purposes other than for which it has been designed.
Never leave high naked flames under the hood when it is in operation.
Adjust the flame intensity to direct it onto the bottom of the pan only, making sure that it does not engulf the sides.
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

Care and cleaning long life Charcoal filter (Green)

The anti-odour ﬁlter can be washed and regenerated every 3-4 months (or more frequently if the hood is subject to intensive use), up to a Max. of 8 regeneration cycles (in case of particularly intensive use it is recommended that you do not exceed 5 cycles).

Regeneration procedure

Wash in the dishwasher at a MAX temperature of 70° or hand wash in hot water without using abrasive sponges (do not use detergents!).
Dry at a MAX temperature of 70° for 2 hours.

Care and cleaning

Grease filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.
Clean the hood using a damp cloth and a neutral liquid detergent.

Installation modes
The hood has been designed to be installed and used either as a “Exhaust mode”, or as a “Recirculation mode”.

Exhaust mode (see symbol in installation booklet) Cooking steam is sucked and channelled outside the house through a discharge duct (not supplied), fitted to the hood steam outlet.
Ensure that the discharge duct is correctly fitted to the air outlet, unit using an appropriate connection system.
Recirculation mode (see symbol in installation booklet)
The air is filtered through one or more charcoal filters, and then resent into room.
Important: Ensure appropriate air circulation around the hood.

Important: If the hood is supplied without charcoal filters and installed on recirculation mode, these must be fitted before the hood can be used. Filters are available in shops. The hood should be installed away from particularly dirty areas, windows, doors and heat sources. The accessories for wall fixing are not included because wall made of different materials require different types of fixing accessories. Use fixing systems suitable for the walls of your home and the weight of the appliance. For more details, contact a specialized dealer. Keep this booklet for future consultation.

Product description

Upper chimney
Lower chimney
Hood body
LED Lighting
Grease filter
Control panel

Control Panel

A

Speed

| Turns the motor on/off at speed one.
---|---
Attention: the product is with the filter alarm disabled.

Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to turn the grease filter alarm on. LED

(B) flashes twice to confirm.

To turn the alarm off, press the button again and hold for at least 2 seconds. The relevant LED (B) flashes once.

B

Speed

| Turns the motor on at speed two / Activate charcoal filter alarm.
Attention: the product is with the filter alarm disabled.

Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to turn the Activated Charcoal Filter alarm on. LED (A) flashes twice to confirm.

To turn the alarm off, press the button again and hold for at least 2 seconds.The relevant LED flashes once (A). Only for recirculation mode.

C

Speed

| Turns the Motor on at speed three / Reset alarm grease filter saturation.
Press and hold the button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the grease filter saturation alarm or charcoal filter alarm. LED (A) flashes three times.

D

Speed

| Turns the motor on at Booster speed.

This speed is timed to run for 6 minutes. At the end of this time, the system returns automatically to the speed that was set before. If it is activated with the motor turned off, it will switch to OFF at the end of the time. To deactivate it, press button D or press button A.

E

Light

| Press briefly: Turns the lighting system on and off at maximum intensity. Press and hold to change the lighting intensity up or down.

General hints

Switch ON the hood at minimum speed when you start cooking and kept it running for few minutes after cooking is finished.
Increase the speed only in case of large amount of smoke and vapour and use boost speed(s) only in extreme situations.
Replace the charcoal filter(s) when necessary to maintain a good odour reduction efficiency.
Clean the grease filter(s) when necessary to maintain a good grease filter efficiency.
Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.

Care and cleaning

Switch off or unplug the appliance from the mains supply before carrying out any maintenance work.

IMPORTANT Clean the hood using a damp cloth and a neutral liquid detergent.
Long Life Charcoal Filter
The anti-odor ﬁlter can be washed and regenerated every 3-4 months (or more frequently if the hood is subject to intensive use), up to a Max. of 8 regeneration cycles (in case of particularly intensive use it is recommended that you do not exceed 5 cycles). IKEA -403.824.98 -KULINARISK -Kitchen -Hood
-3

Grease Filters
Clean or replace the filters continuously according to below time intervals, to maintain good performance of the hood and to prevent a potential fire hazard, caused by excessive grease build-up. The grease filters must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher.

Replacing the lamps
For Replacement please contact an Authorized Service Center.

What to do if…

If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, contact an authorized service center. If you operated the appliance wrongly, or the installation was not carried out according to the Assembly instructions, the visit from the Authorized Service Centre technician may not take place free of charge, even during the warranty period.

PROBLEM	POSSIBLE CAUSE	SOLUTION
Appliance not stable.	The appliance is not correctly installed.	Follow the

Installation instruction enclosed to the appliance.
The appliance is not in a horizontal position.| The appliance is not correctly installed.| Follow the Installation instruction enclosed to the appliance.
Performance in terms of oil capture are not satisfying.| Oil and grease on metal filters or charcoal filters.| Follow the cleaning frequency of filters as described in the user manual.
Appliance does not work.| The appliance is not correctly connected.| Verify that the main cable is connected to the motor group or the plug is connected to the socket.
The light does not work.| The LED is broken.| For replacement, contact the Authorized Service Centre.

Noise of hood is higher than customer expectations.

| Air outlet diameter in the wall is too small, causing a pressure drop and an increase in motor speed.| Follow the Installation instruction enclosed to the appliance.
Product is installed in recirculation mode.| Product in recirculation mode(and using a charcoal filter) will generate an higher noise than a product in extration mode.
More than one bend in the ventilation duct.| If the exhaust system in the building has multiple bend in or a long distance, this can increase the noise of the product.

Button A light flashing once per second.

|

Grease filter alarm.

| Please clean grease filter and reset alarm. Refer to care and cleaning guide for maintenance.

Press and hold the “C” button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the grease filter saturation alarm. LED (A) flashes three times to confirm.

Button A lights flashing twice per second.

|

Charcoal filter alarm.

| Charcoal filter alarm. Please clean charcoal filter and reset alarm. Refer to care and cleaning guide for maintenance.

Press and hold the “C” button for approximately 2 seconds, with all the loads turned off (Motor+Lights), to reset the charcoal filter alarm. LED (A) flashes three

times to confirm

Before contacting the Authorized Service Centre:
Switch the appliance on again to see if the problem has disappeared. If not, switch it off again and repeat the operation after an hour.
If your appliance still does not work properly after carrying out the checks listed in the troubleshooting guide and switching the appliance on again, contact the Author-ized Service Centre, clearly explaining the problem and specifying:

the type of fault;
the model;
the type and serial number of the appliance (given on the rating plate).

Technical Data

| Unit| Value
---|---|---

Product Type/Name/Model

| | KULINARISK 403.824.98 WHO KULI 900 SS

Wall Hanging hood

Dimensions

| Width| mm| 898
Depth| mm| 460
Height min/max| mm| 730/1010
Airflow max – Exhaust| m3/h| 380
Noise max – Exhaust| dBA| 59
Airflow max – Recirculating| m3/h| 340
Noise max – Recirculating| dBA| 74
Total Power| W| 276

Lamps info

| Type| | LED BAR
Number & Power| | 1 x 6W
Socket| | N/A
Installation minimum height – gas hob| mm| 650
Installation minimum height – elec hob| mm| 500
Net Weight| Kg| 15
Voltage| V| 220 – 240
Frequency| Hz| 50-60

```
* Maximum speed (boost excluded).
```

The technical information is situated in the rating plate on the internal side of the appliance.

Energy efficiency

Product Information	Unit	Value

Model identiﬁer

| | KULINARISK 403.824.98 WHO KULI 900 SS

Wall Hanging hood

point

| ****

W

| ****

139

Nominal power of the lighting system| W| 6,0
Average illumination of the lighting system on the cooking surface| lux| 350
Measured power consumption in standby mode| W| N/A
Measured power consumption off mode| W| 0,49
Sound power level at maximum speed (boost excluded)| dBA| 59

Energy saving
The appliance contains features which help you save energy during everyday cooking.

Environment concerns

Maintenance

The symbol on the product or on its packaging indicates that this prod-uct may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential nega-tive consequences for the environ-ment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Packaging materials
The materials with the symbol are recyclable. Dispose the packaging in suitable collection containers to recycle it.

IKEA GUARANTEE

How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years from the original date of purchase of your appliance at IKEA. The original sales receipt, is required as proof of purchase. If service work is carried out under guarantee, this will not extend the guarantee period for the appliance.

Who will execute the service?

IKEA service provider will provide the service through its own service op- erations or authorized service partner network.
What does this guarantee cover?

The guarantee covers faults of the ap-pliance, which have been caused by faulty construction or material faults from the date of purchase from IKEA. This guarantee applies to domestic use only. The exceptions are specified under the headline “What is not covered under this guarantee?” Within the guarantee period, the costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that the appliance is accessible for repair without special expenditure. On these conditions, the respective local regulations are applica-ble. Replaced parts become the prop-erty of IKEA.

What will IKEA do to correct the problem?
IKEA appointed Service Provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee. If considered covered, IKEA Service Provider or its authorized service partner through its own service operations, will then, at its sole discre-tion, either repair the defective product or replace it with the same or a compa-rable product.
What is not covered under this guarantee?

Normal wear and tear.
Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect instal-lation or by connection to the wrong voltage, damage caused by chemi-cal or electrochemical reaction, rust, corrosion or water damage including but not limited to damage caused by excessive lime in the water supply, damage caused by abnormal environ-mental conditions.
Consumable parts including batteries and lamps.
Non-functional and decorative parts which do not affect normal use of the appliance, including any scratches and possible color differences.
Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap drawers.
Damage to the following parts: ce-ramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults.
Cases where no fault could be found during a technician’s visit.
Repairs not carried out by our ap-pointed service providers and/or an authorized service contractual partner or where non-original parts have been used.
Repairs caused by installation which is faulty or not according to specifica-tion.
The use of the appliance in a non-do-mestic environment i.e. professional use.
transportation damages. If a cus-tomer transports the product to his home or another address, IKEA is not liable for any damage that may occur during transport. However, if IKEA delivers the product to the customer’s delivery address, then damage to the product that occurs during this deliv-ery will be covered by IKEA.
Cost for carrying out the initial instal-lation of the IKEA appliance. Provider or its authorized service part-ner repairs or replaces the appliance under the terms of this guarantee, the appointed Service Provider or its au-thorized service partner will reinstall the repaired appliance or install the replacement, if necessary.

How country law applies
The IKEA guarantee gives You specific legal rights, which covers or exceed local demands. However these conditions do not limit in any way consumer rights described in the local legislation

The dedicated After Sales Service for IKEA appliances:
Please don’t hesitate to contact IKEA appointed After Sales Service Provider to:

make a service request under this guarantee;
ask for clarification on installation of the IKEA appliance in the dedicated IKEA kitchen furniture. The service won’t provide clarifications related to:
- the overall IKEA kitchen installation;
- connections to electricity (if machi-necomes without plug and cable), to water and to gas since they have to be executed by an authorized service engineer.
ask for clarification on functions of IKEA appliances.To ensure that we provide you with the best assistance, please read carefully the Assembly Instructions and/or the User Manual before contacting us.
How to reach us if You need our service

Please refer to the last page of this manual for the full list of IKEA- appointed contacts and relative national phone numbers.
Important!
In order to provide you a quicker service, we recommend using the specific phone numbers listed on this manual. Always refer to the numbers listed in the booklet of the specific appliance you need assistance for. Please also always refer to the IKEA article number (8 digit code) and 12 digit service number placed on the rating plate of your appliance.
Important!
SAVE THE SALES RECEIPT!
It is your proof of purchase and required for the guarantee to apply. The sales receipt also reports the IKEA name and article number (8 digit code) for each of the appliances you have purchased.

Do you need extra help?
For any additional questions not related to After Sales of your appliances please contact your nearest IKEA store call centre. We recommend you read the appliance documentation carefully be-fore contacting us.

Coverage for equipment purchased in Russia
This warranty is applicable only to equipment purchased in Russia. The warranty service obligations remain in force only if the item was installed in accordance with the following require-ments:

the technical requirements accepted in the country where the customer applied for warranty service;
the safety rules given in the installa-tion instructions and user manual.

Produced for IKEA:
The importer and the entity authorized by the manufacturer:
The importer and the entity authorized by the manufacturer: LLC “IKEA TORG”, bld. 1, micro rayon IKEA, Khimki, Moscow region, 141400 Russia, tel.: +7(495) 737-5301, fax: +7(495) 737-5324
This device was designed, manufactured, and sold in accordance with the standards of the Customs Union technical regulations, and with local normative legal documents.
Made in Italy

For IKEA product quality issues, contact the seller: LLCOOO IKEA DOM, bld. 1, micro rayon IKEA, Khimki, Moscow region, 141400 Russia; tel.: +7 495-666-2929, www.ikea.ru The date of manufacture of the article is indicated in the serial number, where the first figure corresponds to the last one of the production year and the second and the third figures are the consecutive week number. For example, serial number 830 12345 means that the article was produced on the thirtieth week of 2018.

Life cycle: 10 years
After life cycle is finished, your product can become dangerous. So, after life cycle has been finished, or in case you decided to stop using the product earlier, please address to appropriate officials to legally destroy the appliance”
Information of Storage and Transportation
Store in a dry place indoors.
Transport the product in it´s original packaging. IKEA -403.824.98
-KULINARISK -Kitchen -Hood -7