tp-link TL-SM331T 1000Base-T RJ45 SFP Module Installation Guide

tp-link TL-SM331T 1000Base-T RJ45 SFP Module Installation Guide

Installing the RJ45 SFP / RJ45 SFP+ Module

1. Lock the yellow latch into place and insert the module into an SFP / SFP+ slot with label side up.
   

2. Gently push the module into the slot until you hear a click. Then, insert the RJ45 network cable
   .

Removing the RJ45 SFP / RJ45 SFP+ Module

1. Press the RJ45 crystal head and pull out the cable.
   

2. Pull down the latch and remove the module.
   

Positioning the 10G RJ45 SFP+ Modules

The 10G RJ45 SFP+ modules consume more power than optical modules. This may result in higher heat. To avoid overheating, it is recommended to place the
modules separated by multiple optical transceivers or empty slots. When used in high temperature environments, additional cooling must be applied.
The figures below only show the recommended positioning. The actual number of modules that can be inserted depends on the switch’s heat dissipation and power margin.

Scenario 1:

Scenario 2:

Specifications

General Specifications

Environmental and Physical Specifications

We recommend that you use only TP-Link modules on your TP-Link devices.
To check the compatible TP-Link devices of your module, please visit our website:

• TL-SM331T:
  https://www.tp-link.com/tl-sm331t/product-list/

• TL-SM5310-T:
  https://www.tp-link.com/tl-sm5310-t/product-list/

Note:

1. TL-SM331T does not support the data rate of 10 Mbps or 100 Mbps.TL-SM
   5310-T does not support the data rate of 10 Mbps, but supports 100 Mbps /

2. Gbps / 2.5 Gbps / 5 Gbps / 10 Gbps.

3. When a Gigabit RJ45 SFP module is inserted into a 10 Gbps SFP+ slot, extra configuration may be required.

4. When the 10G RJ45 SFP+ module is inserted into a 10 Gbps SFP+ slot and the maximum rate of the peer connection port is 5 Gbps, 2.5 Gbps, 1 Gbps, or 100 Mbps, the flow control for the 10 Gbps SFP+ slot needs to be manually enabled.

Safety Information

• Keep the device away from water, fire, humidity or hot environments.

• Do not touch the device while it is operating.

• To prevent potential risks caused by heat, do not place your network device on
  non-heat-resistant paper, cloth, fabrics, plastics, or any other surface that
  doesn’t provide space beneath your device for heat dissipation.

• The air flow around the device should be increased, or the overall ambient temperature should be lowered to keep the temperature of the modules within the recommended range.
  Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essentialrequirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp- link.com/en/support/ce.

UK Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essentialrequirements and other relevant provisions of the Electromagnetic Compatibility
Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK Declaration of Conformity may be found at https://www.tp- link.com/support/ukca

Read More About This Manual & Download PDF:

References

• 域名售卖
• TP-Link Community
• CE Regulatory Compliance | TP-Link
• Regulatory Compliance | TP-Link
• TL-SM331T Compatibility List
• TL-SM5310-T Compatibility List

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>