FURINE X07 Wireless Gaming Headset User Manual

FURINE X07 Wireless Gaming Headset

Device

|

Wireless

(2.4GHz & BT5.0)

|

Wired

(3.5mm audio jack)

---|---|---
Sound| Mic| Button Function| Sound| Mic| Button Function
Desktop| √| √| √| √| √| ×
Mac| √| √| √| √| √| ×
Laptop| √| √| √| √| √| ×
Tablet PC| √| √| √| √| √| ×

Mobile Phone

| √

(only BT5.0)

| √

(only BT5.0)

| √

(only BT5.0)

|

√

|

√

|

×

PS4/PS5

Console

|

√

(only 2.4GHz)

|

√

(only 2.4GHz)

|

√

(only 2.4GHz)

|

√

|

√

|

×

PS4/PS5

Controller

|

×

|

×

|

×

|

√

|

√

|

×

Xbox Console

|

×

|

×

|

×

|

×

|

×

|

×

Xbox Controller

|

×

|

×

|

×

|

√

|

√

|

×

Switch| √| ×| ×| √| ×| ×

Package Contents

Overview

Button Function

Power Button

| Press button 1 time| Pause / play sound
---|---|---
Press button 2 times quickly| Switch 2.4GHz & BT5.0 connection
Hold button for 3 seconds| Power on/off

Mic Mute Button

| Press button 1 time| Mic on/off
Press button 2 times quickly| Switch gaming & music mode
Hold button for 3 seconds| RGB light on/off
Volume+ Button| Press button 1 time| Volume up
Hold button for 3 seconds| Play last song
Volume- Button| Press button 1 time| Volume down
Hold button for 3 seconds| Play next song

Note:

1. Permanent hearing damage can occur if a headset is used at high volumes for extended periods of time.
2. Turn on the microphone by default after power on.
3. Press the power button and volume+ button simultaneously, after hearing the “disconnected” voice prompt, the headset will disconnect from the connected devices, and you could re-select the other device to connect

Status LED

Note:

1. If the headset is disconnected from your devices and no operation is performed for 10 minutes, the headset will turn off automatically.
2. After connected with your devices, if no operations are performed, the headset will turn off after 10 minutes.
3. Insert the 3.5mm audio cable, then the headset will enter into the wired mode.
4. In wired mode, the RGB light and buttons cannot be operated.
5. In wired mode, the microphone will automatically turn on, and only unplugging the mic can turn off the microphone.
6. In wireless mode, unplugging the mic or pressing the mic mute button one time can turn off the microphone.
7. Low Battery Reminder: When you hear the low battery tone ‘battery low’ and the indicator light flashes, please charge the headset in time.

Charging

It is recommended to fully charge the headset before first use.

Note:

1. Please charge the headset with 5V/1A standard adapter;
2. Generally, it takes 4 hours to fully charge the headset, but the actual charging time depends on your charging devices;
3. The headset couldn’t turn on while charging.

Using with PC/Mac in Wireless Mode

1. Connect the 2.4GHZ Wireless Transmitter.
2. Power on the headset.
3. When the status LED displays solid white or blue light, then the headset is connected.

1. Open sOund settings.
2. Choose your output device X07.
3. Choose your input device X07.
4. FURINE X07 wireless headset can be used.

Using with PS4/PS5 Console in Wireless Mode

Using with P$4/PS5/Xbox Controller in Wired Mode

Note:

1. Insert the 3.5mm audio cable, then the headset turns off and enters the wired mode.
2. The microphone will turn on and the buttons cannot be operated in wired mode by default.
3. Wireless mode is not available for Xbox.

Using with Phone in BT5.0 Mode

Note:

1. If you want to go back to the 2.4GHz wireless mode, you can press the power button 2 times.
2. Frequent switching of modes will cause the headset connection to slow down.

Specification

• Model X07
• Driver diameter 50mm
• Speaker frequency response 20-20KHZ
• Speaker impedance- 320
• Battery parameter Working voltage 3.7V/1200mAh
• Working current 70mA
• Charging time about 4 hours
• Input charging standard USB Type-C, DC 5V/1A
• Mic sensitivity . -42+3dB (Omnidirectional)
• Wireless range up to 65 feet (no obstacles between)

Troubleshooting

Wireless mode:

1. Check if you’ve set the headset as the default recording device;
2. Check if the microphone is turned off.

Wired mode:

1. Make sure the cable is connected tightly:
2. Microphones can not use when connecting to Some PC in wired mode. May require a 3.5mm 4-pole to mic/stereo splitter adapter (not included).

No sound or intermittent sound from the headset

1. Check if there are other obstacles that affect the transmission.
2. If the intermittent sound occurs when you are communicating, please check if the network works smoothly;
3. Check if you’ve set the headset as the default recording device;
4. Check if the headset is in lowest volume setting.

Can’t connect to devices

1. Check if you useda USB Extension or a USB Hub (it is not recommended);
2. Plug directly into the USB jack of the device’s host;
3. Try to Replace a USB jack (some USB jacks may be power shortage);
4. For PC, it is recommended to plug into the USB jack at the back of the host;
5. Observe the indicator light and check if the headset is already connected with other devices.

Can’t connect to devices in BT mode

1. Check if both the headset and your device open the BT mode, try to reduce the middle distance, and reconnect again.
2. Double press the power button to switch to the BT mode.
3. After power off, press and hold the power button for 7 seconds, the headset will clear the connection records and shut dovwn. Delete the connection record of the headset in your device and reconnect the headset to your device again.

FCC

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment The devices has been evaluated to meet general RF exposure requirement， the device can be used in portable exposure condition without estriction

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>