shopvac 610 WET-DRY VACUUM User Manual

: June 5, 2024
: shopvac

shopvac 610 WET-DRY VACUUM

shopvac-610-WET-DRY-VACUUM

Description

The Shop-Vac® Wet/Dry vacuum cleaners are for vacuuming wet and dry non- volatile materials. Equipped with powerful, permanently lubricated, Single or Two-Stage By-Pass motors. Standard ﬁltration systems to handle dry or wet pick up. Double ﬁltration is available for most Shop-Vac® Vacs and is standard on Shop-Vac® Commercial Vacuums. Equipped with heavy-duty dolly or easy roll caster system. Automatic ﬂoat shut off prevents overﬂow during wet pick up. Includes versatile 1¼” (3.18cm), 1½” (3.81cm) or 2½” (6.35cm) diameter accessories. Tank styles include steel with rust resistant epoxy phenolic coated interiors, durable stainless steel and rugged dent resistant polypropylene tank. cULus listed.

ATTENTION! Read all safety rules carefully before attempting to operate. Retain for future reference.
DANGER: Never operate this unit when ﬂammable materials or vapors are present because electrical devices produce arcs or sparks that can cause a ﬁre or explosion. NEVER OPERATE UNATTENDED!
For your records, please record the following information and store this user manual in a safe location.

Catalog No: (Located on the carton)
Model No: (Located on top portion of the vacuum)
Purchase Date:

TOOLS NEEDED

shopvac-610-WET-DRY-VACUUM-1

IMPORTANT SAFETY INSTRUCTIONS

When using an electric appliance, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE.
WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

Do not leave appliance when plugged in. Unplug from outlet when not in use and before servicing. Connect to a properly grounded outlet only. See Grounding Instructions.
Do not expose to rain – store indoors.
Do not allow to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only Manufacturer’s recommended attachments.
Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors or dropped into water, contact Shop-Vac Corporation for assistance.
Do Not: pull or carry by cord, use cord as a handle, close a door on cord or pull cord around sharp edges or corners. Do not run appliance over cord. Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To unplug, grasp the plug; not the cord.
Do not handle plug or appliance with wet hands.
Do not put any object into openings. Do not use with any openings blocked; keep free of dust, lint, hair and anything that may reduce air ﬂow.
Keep hair, loose clothing, ﬁngers and all parts of body away from openings and moving parts.
Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes.
Do not use without dust bag and/or ﬁlters in place.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not use to pick up ﬂammable or combustible liquids such as gasoline or use in areas where they may be present.
Do not use your cleaner as a sprayer of ﬂammable liquids such as oil base paints, lacquers, household cleaners, etc.
Do not vacuum toxic, carcinogenic, combustible or other hazardous materials such as asbestos, arsenic, barium, beryllium, lead, pesticides or other health endangering materials. Specially designed units are available for these purposes.
Do not pick up soot, cement, plaster or drywall dust without cartridge ﬁlter and collection ﬁlter bag in place. These are very ﬁne particles that may pass through the foam and affect the performance of the motor or be exhausted back into the air. Additional collection ﬁlter bags are available.
Do not leave the cord lying on the ﬂoor once you have ﬁnished the cleaning job. It can become a tripping hazard.
Use special care when emptying heavily loaded tanks.
To avoid spontaneous combustion, empty tank after each use.
The operation of a utility vac can result in foreign objects being blown into eyes, which can result in eye damage. Always wear safety goggles when operating vacuum.
STAY ALERT. Watch what you are doing and use common sense. Do not use vacuum cleaner when you are tired, distracted or under the inﬂuence of drugs, alcohol or medication causing diminished control.
WARNING! Do NOT use this vacuum cleaner to vacuum lead paint debris because this may disperse ﬁne lead particles into the air. This vacuum cleaner is not intended for use under EPA Regulation 40 CFR Part 745 for lead paint material cleanup.

SAVE THESE INSTRUCTIONS
WARNING – DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND/OR OPERATING USE.

GROUNDING INSTRUCTIONS

This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This appliance is equipped with
a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING – IMPROPER CONNECTION OF THE EQUIPMENT-GROUNDING
CONDUCTOR CAN RESULT IN A RISK OF ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE

This appliance is for use on a nominal 120-volt circuit, and has a grounded plug that looks like the plug illustrated in sketch A. A temporary adaptor that looks like the adaptor illustrated in sketches B and C may be used to connect this plug to a 2-pole receptacle as shown in sketch B if a properly grounded outlet is not available. The temporary adaptor should be used only until a properly grounded outlet (sketch A) can be installed by a qualiﬁed electrician. The green colored rigid ear, lug or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover. Whenever the adaptor is used, it must be held in place by a metal screw.
IN CaNada, tHe uSe oF a temporary adaptor IS Not permItted by tHe CaNadIaN eleCtrICal CODE.

EXTENSION CORDS

When using the appliance at a distance where an extension cord becomes necessary, a 3-conductor grounding cord of adequate size must be used for safety, and to prevent loss of power and overheating. Use Table A to determine A.W.G. wire size required. To determine ampere rating of your vacuum, refer to nameplate located on motor housing. Before using appliance, inspect power cord for loose or exposed wires and damaged insulation. Make any needed repairs or replacements before using your appliance. Use only three-wire outdoor extension cords which have three prong grounding-type plugs and three-pole receptacles which accept the extension cord’s plug. When vacuuming liquids, be sure the extension cord connection does not come in contact with the liquid. UNPACKING:
Remove vacuum cleaner and all accessories from the carton. Important: Open tank cover by pushing latches or clamps outward with thumbs and remove any accessories that may have been shipped in the tank.

ASSEMBLY

TOP HANDLE
If the top handle is not installed on your unit, align holes in handle and holes in motor cover and secure with screws provided.

CASTER SYSTEM
Follow the instructions for the caster system that came with your vacuum. metal taNk wItH plaStIC dolly aNd Four CaSterS You will ﬁnd four casters with your wet/dry vacuum. Assemble as follows:

With the cord disconnected from the receptacle and tank cover removed, turn tank upside down so that bottom is facing up.
Insert casters into bottom of dolly by placing stem of caster into holes provided. Apply pressure and twisting motion until casters snap into place.
Return tank to upright position.

Metal Tank with plastic dolly and rear wheels

Make sure the cord is disconnected from the receptacle then remove the tank cover.
If your unit is 4 U.S. gallon (15.1 liter) to 14 U.S. gallon (53 liter), assemble as follows:
- a. Turn tank upside down so the bottom is facing up.
- b. Continue on to step 4 below.
If your unit is 16 U.S. gallon (60.5 liter) or above, assemble as follows:
- a. With the tank upright and back facing you, insert square nut into one of the two slots located in back of dolly.
- b. Place metal ﬂat washer over stem of screw.
- c. Tilt the tank forward slightly and locate the hole provided in the underside of the dolly directly below the slot containing the square nut.
- d. Place the screw, containing the ﬂat washer, into the hole and turn clockwise until end of screw is connected to square nut. If you have difﬁculty getting the screw to connect to the square nut, push downward on the square nut with the eraser end of a pencil while turning the screw.
- e. Finish tightening the screw using 7/16” socket, wrench or nut driver.
- f. Repeat steps a to e with the second slot in dolly.
- g. Turn tank upside down so bottom is facing up. Continue on to step 4 below.
Place axle upright on a hard surface and hammer on one cap nut.
Place one wheel on axle and slide down to cap nut. Be sure ﬂat side of wheel hub is facing outward. If metal spacers (not needed for all models) came in the hardware pack, place one on axle and slide down to wheel.
Slide axle through holes provided in tool rack. If included, slide second metal spacer (not needed for all models) over axle and slide down to tool rack.
Slide remaining wheel onto axle and hammer on second cap nut.
Install tool rack assembly onto dolly (already installed on tank) by placing large slot in tool rack over rim on back of dolly. Push tool rack onto dolly until the bottom of tool rack is ﬂush with bottom of dolly.
NOTE: It is normal for tool rack to ﬁt tightly onto dolly.
Secure with four screws provided.
If plastic ﬂat washers are included in hardware pack, place one ﬂat washer over stem of each caster. NOTE: Flat washers are not required with all units.
Insert casters into front of dolly by placing stem of casters into holes provided. Apply pressure and twisting motion until casters snap into place.
Return tank to upright position.

Metal taNk wItH metal dolly
Refer to the item number and description chart at the end of these instructions to assist you in assembling the dolly. Tools required: (2) 1/2 inch open end wrenches, (2) 7/16 inch open end wrenches, or a socket set and a hammer.

Insert 2½ inch long bolt through center hole in rear frame, attach split lock washer and nut and tighten securely.
Attach handle brace to back of rear frame with 5/8 inch long machine screws, lock washers, and nuts. (Finger tighten only.)
Position main frame inside rear frame. Attach (2) 5/8 inch long machine screws, lock washers and nuts in both sides. Tighten securely.
Attach handle uprights, inside main frame (make sure buttons at top face inward) using 5/8 inch long machine screws, lock washers and nuts. (Finger tighten only.) Align holes at top of handle braces with holes in handle uprights. Attach with 1¼ inch long machine screws, lock washers and nuts. (Tighten securely.)
Go back and tighten machine screws at bottom of uprights and braces.
Attach caster sockets (open end down) to front of main frame using 5/8 inch long machine screws, lock washers and nuts. Insert casters into sockets.
Slide basket adapters on handle. See images below for correct installation of adapters.
Attach handle onto uprights by pushing down and holding buttons in on uprights.
Place tank retaining bracket through slot and bolt in rear frame and screw on knob.
Slide bumper down over main dolly frame until it bottoms out.
Place axle upright on a hard surface and hammer on (1) cap nut. Place (1) wheel on axle and slide down to cap nut. Slide axle through rear of frame and slide on other wheel. Before assembling cap nut on other end of axle, be certain dolly is assembled correctly. (You may place tank on dolly and tighten knob of retaining bracket to be sure of correct assembly.)
After ensuring dolly is assembled correctly remove tank and place dolly on side with installed cap nut on hard surface and hammer second cap nut on axle.
Place accessory basket on adapters and pull out on outer rim of basket and snap into place.

ITEM NUMBER & DESCRIPTION

shopvac-610-WET-DRY-
VACUUM-13

Handle
Handle upright
Handle brace
¼ – 20 x 1¼” Hex head machine screw (Black)
5. ¼” External tooth lockwasher
¼ – 20 Hex nut (Black)
Rear dolly frame
Main dolly frame
5/16 – 18 x 2½” Hex head bolt
5/16″ Split lockwash
5/16 – 18 Hex nut
Tank retainer bracket
Threaded knob
Axle
¼ – 20 x 5/8″ Hex head machine screw
¼ – 20 Hex nut
Caster socket
Caster
Bumper
10″ Wheel (25.4cm)
Cap nut
Accessory basket
Basket adapter

BAND DOLLY

Place casters into sockets on band assembly.
Place tank upside down and slip band assembly over lip on bottom of tank.
Insert bolt and tighten nut until secure.

ITEM NUMBER & DESCRIPTION

55 Gal. band assembly
Caster
Hex head bolt, ¼ – 20 x 1¾
Hex nut, ¼ – 20

CARRIAGE HANDLE Follow the instructions for the carriage handle that came with your vacuum. If your side tank handles look like the ones pictured to the right, follow these instructions. You will ﬁnd one carriage handle and a handle pack containing two side tank handles, four handle supports and eight screws. Assemble as follows:

Take two handle supports and two 1” screws. Place screws through the hole provided in center of each support.
Position the tank, in the upright position, with the inlet facing you. Put the support assemblies inside the tank, then place the screws through the holes provided on left side of the tank. Make sure the plastic portion is located inside the tank. Turn the supports until the back of the supports ﬁt ﬂush against the inside curve of the tank.
Remove any webbing that attaches the tank handles to each other. Take the side tank handle with the letter L and position it on the outside of the tank where the support assemblies are installed. The U-shaped cutout on the bottom end of the handle must face the rear of the tank. Secure the side tank handle to the tank with the screws in the support assemblies.
Repeat steps 1 to 3 using right side of tank and the remaining side tank handle marked with the letter R.
Position metal carriage handle outside of tank and under the tank handles. Be sure to spread ends of carriage handle when assembling to prevent damage to tank. Line up holes in ends of carriage handle with holes in the bottom of tank handles. Make sure carriage handle is in the U-shaped cut on the tank handles (located towards rear of unit). Secure with 1½” screws provided.

All other side tank handles, follow these instructions.
Attach carriage handle to tank by inserting bolt through the center hole of handle and tank, secure with nut provided. Attach side handles with screws provided. Be sure to spread ends of carriage handle when assembling to prevent damage to tank. shopvac-610-WET-DRY-VACUUM-19

BASKET
If your unit came with a basket, insert basket through center of carriage handle and slide into place. The basket does not come standard with all models.

SIDE TANK HANDLES
If your unit came with side tank handles, attach handles to tank with screws provided.

TOOL HOLDER (Not standard with all models)
If your unit came with a tool holder, assemble as follows:

Set tank cover onto the tank. Position with back of tank cover facing you.
Take tool holder and place tabs on tool holder into slots on back of tank cover.
Press down until tabs snap into place. Remove tank cover from tank and refer to the set up and operation section.

SET UP AND OPERATION

DANGER – This equipment incorporates parts such as switches, motors or the like that tend to produce arcs or sparks that can cause an explosion. Do not pick up ﬂammable, combustible, or hot materials. Do not use around explosive liquids or vapors, as electrical devices produce arcs or sparks which can cause a ﬁre or explosion – do not use at ﬁlling stations or anywhere gasoline is stored or dispensed.

Refer to the ﬁlter installation and maintenance section to make sure the correct ﬁlters are installed for your cleaning operation.
Replace tank cover. Make sure each latch or clamp is secured over the raised area of the tank cover. Failure to properly secure the latches could cause the tank cover to release from the tank.
Install machine hose end into inlet located on the front of the tank.
Attach the desired cleaning accessory onto the accessory end of the hose. NOTE: Many more useful tools are available at your local dealer or the Shop-Vac® website.
Plug the cord into the wall outlet. Your cleaner is ready for use. I = ON, O = OFF

ACCESSORIES, HOSES AND WANDS
All Shop-Vac® vacuums covered in this manual come with accessories to cover wet and dry cleanup jobs. Not all vacs include all accessories shown. shopvac-610-WET-DRY-VACUUM-24

FILTER INSTALLATION AND MAINTENANCE

**FILTRATION SYSTEM

There are a variety of ﬁlters available for your vacuum. There are cage ﬁlters that install onto the underside of the tank cover and tank ﬁlters that install into the tank. The ﬁlters are grouped into three ﬁltration categories. General ﬁltration is used for large debris; such as, wood chips, nails and gravel. Medium ﬁltration is used for medium debris; such as, dirt, sand and sawdust. Fine ﬁltration is used for ﬁne debris; such as drywall dust, cold ash and cement dust. It is important to have the correct ﬁlters installed for your cleaning operation to protect your vacuum motor.
NOTE: When using the vacuum to pick up very ﬁne dust. It will be necessary to empty the tank and clean the cage ﬁlter at more frequent intervals to maintain maximum pick up power or add a disposable ﬁlter bag.

DRY PICK UP OPERATION

NOTE: Never use the vacuum for dry pick up without a dry use ﬁlter installed. Using the vacuum without a ﬁlter will cause dust to discharge from the blower port and cause damage to the motor.
WARNING – ALWAYS DISCONNECT THE PLUG FROM THE WALL OUTLET BEFORE REMOVING THE TANK COVER.
Follow the instructions for the ﬁlter that came with your vacuum. Some ﬁlters mentioned do not come standard with all vacuums. Additional ﬁlters are available at your local dealer or the Shop-Vac® website.

CARTRIDGE FILTER
The cartridge ﬁlter can be used for dry pick up and small quantities of wet pick up. Installation is the same for both. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag must be used with the cartridge ﬁlter.

If a foam sleeve is installed on the lid cage, remove it by sliding it off the lid cage. NOTE: If the cartridge ﬁlter has been used for wet pick up, it must be cleaned and dried before using it for dry pick up.
With the tank cover in an upside down position, slide the cartridge down over the lid cage, pushing until the ﬁlter seals against the cover.
Place the filter retainer into the top of the cartridge filter. Hold the tank cover with one hand, turn the handle on the ﬁlter retainer clockwise to lock the ﬁlter into place.
To remove the ﬁlter for cleaning, hold the tank cover and turn the ﬁlter retainer counter-clockwise to loosen and remove.
Slide the cartridge ﬁlter off the lid cage.
For standard cartridge ﬁlters and Ultra-Web® cartridge ﬁlters, clean the ﬁlter by shaking or gently brushing off excess dirt. Extremely dirty ﬁlters may be cleaned with water by rinsing from the inside of the ﬁlter. Dry completely (approximately 24 hours).
For CleanStream® Abrasive Resistant cartridge ﬁlter, tap end cap against hard surface to loosen debris. Additional debris can be removed by rinsing outside surface of the ﬁlter with running water. Avoid dampening inside of filter. Completely air dry after washing. ImportaNt: do Not bruSH. do Not clean ﬁlter with abrasive materials or scrub between pleats. This will permanently damage the ﬁlters ability to stop dust.
Check the ﬁlter for tears or small holes. If none are found, reinstall the ﬁlter. To prevent damage to your vacuum, do not use a ﬁlter with a hole or tear.

NOTICE – This ﬁlter is made of high quality paper designed to stop small particles of dust. The ﬁlter can be used for wet or dry pick up. A dry ﬁlter is necessary to pick up dry material. If you use your vac to pick up dust when the ﬁlter is wet, the ﬁlter will clog quickly and be very difﬁcult to clean. The ﬁlter may become saturated when picking up large quantities of liquid causing misting to appear in the exhaust air. At this time, you should dry or change the ﬁlter to eliminate this occurrence. Please handle the ﬁlter carefully when removing it for cleaning or when installing it. Check the ﬁlter for tears or small holes. Even a small hole can cause dust to be exhausted. Do not use a ﬁlter with holes or tears. Replace it immediately.
WARNING – KEEP FILTERS CLEAN. EFFICIENCY OF THE VACUUM IS LARGELY DEPENDENT ON THE FILTER. A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY
DAMAGE THE CLEANER. CHECK THE FILTER PERIODICALLY AND REPLACE AS REQUIRED.

DISPOSABLE FILTER BAG
Use the disposable ﬁlter bag in conjunction with the cartridge ﬁlter for easy disposal of the debris. The bag is not required for normal dry pick up. When picking up ﬁne dust or powders a high efﬁciency ﬁlter bag must be used.
NOTE: For dry use only.
Follow the instructions that pertain to your vacuum.

TANK WITH STATIONARY INLET DEFLECTOR:

Make sure the cord is disconnected from the receptacle, tank cover is removed and the hose is disconnected from tank inlet.
Grasp the cardboard collar ﬁrmly and slide rubber guard onto inlet ﬁtting as far as possible.
When secured in place, expand the ﬁlter bag and position around the inside of the tank.

TANK WITH REMOVABLE INLET DEFLECTOR:

Make sure the cord is disconnected from the receptacle, tank cover is removed and the hose is disconnected from tank inlet.
Remove inlet deﬂector from deﬂector guide. NOTE: Hose must be removed before inlet deﬂector can be taken out.
With the opening of the inlet deﬂector facing the left or right side of the ﬁlter bag, slide ﬁlter bag collar over deﬂector matching notches of bag collar to tabs on inlet deﬂector. Bag will only ﬁt properly one way.
Slide deﬂector with ﬁlter bag attached into deﬂector guide.
Reinsert hose into inlet and tighten locking-nut. When secured in place expand bag and position around inside of tank.
NOTE: When removing ﬁlter bag from tank, remove inlet deﬂector from ﬁlter bag collar and reinstall into deﬂector guide. Inlet deﬂector should always be in place for any type of cleaning.

WARNING – FOR FINE DUST AND POWDERS.

When vacuuming ﬁne dust, or powders of any kind (plaster, drywall dust, cold ashes, concrete dust, etc.) a high efﬁciency drywall ﬁlter bag must be used. When vacuuming normal household dust and debris, standard household disposable ﬁlter bags may be used.

WET PICK UP OPERATION

Your vacuum can be used for wet pick up. Remove ALL dirt and debris found in the tank. Remove all dry use ﬁlters, including the ﬁlter bag, from the vacuum.
A clean cartridge ﬁlter may be used to pick up small quantities of liquid. To use the cartridge ﬁlter; follow the instructions under dry pick up.
For vacuuming large quantities of liquid use a foam sleeve. If a foam sleeve did not come standard with your unit, one may be purchased at your local dealer, the Shop-Vac® website or by contacting Shop-Vac® customer service. To use the foam sleeve; follow the instructions in this section.
Misting in the exhaust air or dripping of liquid around the tank cover may occur if the ﬁlter becomes saturated during wet pick up. If this occurs, remove the ﬁlter and allow to dry, or replace with another dry ﬁlter.
Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be emptied. When the tank is full, suction will drastically reduce. Refer to the automatic suction shut
off section for more information. Raise the hose to drain any excess liquid into the tank. Follow the instructions in the emptying liquid waste section.
Before storing the vacuum cleaner or using for dry pick up, clean and dry the interior of the tank and the underside of the tank cover. Clean and allow the ﬁlters to dry completely.
Wet pick up accessories should be washed periodically; especially after picking up wet, sticky kitchen accidents. This can be accomplished with a warm solution of soap and water.

FOAM SLEEVE

With the tank cover in an upside down position, slide the foam sleeve down over the lid cage, pulling until foam sleeve completely covers the lid cage.
To clean the foam sleeve, slide it up and off the lid cage. Shake excess debris off of the foam sleeve with a rapid up and down movement.
Hold foam sleeve under running water for a couple minutes, rinsing from the inside of the ﬁlter. A water wash is not always required, depending on the condition of the ﬁlter.
Check the ﬁlter for tears. If any are found, replace with a new ﬁlter.

BLOWER FEATURE

Your vacuum can be used as a powerful blower. To use the blower feature, clear the hose of any debris or obstructions. For vacuums with a blower port cover (not standard on all models), unscrew blower port cover located on the back of tank cover. The blower port cover is equipped with a retaining strap to prevent loss of the cover. NOTE: For maximum performance when vacuuming, remove the blower port cover.
Insert machine hose end into blower port located on the back of the tank cover. Twist the hose end slightly to tighten the connection. Caution should be used when using as a blower due to the powerful force of air when using certain attachments.
WARNING – ALWAYS WEAR EYE PROTECTION TO PREVENT ROCKS OR DEBRIS FROM BEING BLOWN OR RICOCHETING INTO THE EYES OR FACE WHICH CAN RESULT IN SERIOUS INJURY.

EMPTYING LIQUID WASTE FROM THE TANK

To empty liquid waste from the tank, turn the vacuum off and remove the plug from the wall outlet. Follow the instructions that pertain to your vacuum.

WITHOUT TANK DRAIN
Remove the tank cover and deposit the liquid waste in a suitable drain. Use side carry handles for lifting vac when draining tank into drains that are located above ﬂoor level. After tank is empty, return the tank cover to its original position.

WITH TANK DRAIN
Remove the drain cap and deposit the liquid waste in a suitable drain. Use side carry handles for lifting vac when draining tank into drains that are located above ﬂoor level. After the tank is empty, return the drain cap to it’s original position.

AUTOMATIC SUCTION SHUT OFF

The vacuum is equipped with an automatic suction shut-off that operates when picking up liquids. As the level of the liquid rises in the tank, an internal ﬂoat rises until it seats itself against a seal at the intake of the motor, shutting off suction. When this happens, the motor will develop a higher than normal pitch noise and the suction is drastically reduced. If this occurs, turn unit off immediately. Failure to turn unit off after ﬂoat rises and shuts off suction will result in extensive damage to the motor. To continue use, empty the liquid waste from the tank as outlined in the previous section.

NOTE: IF aCCIdeNtally tIpped over, tHe vaCuum Could loSe SuCtIoN, IF tHIS oCCurS, turN uNIt oFF aNd plaCe vaC IN uprIGHt poSItIoN. tHIS wIll allow tHe Float to returN to ItS Normal POSITION AND YOU WILL BE ABLE TO CONTINUE OPERATION.

LUBRICATION
No lubrication is necessary as the motor is equipped with lifetime lubricated bearings.

STORAGE
Before storing your vacuum the tank should be emptied and cleaned. Never allow liquids to sit in the tank for any extended period of time. The vacuum should be stored indoors.

SERVICE
Do not attempt to service your Shop-Vac® wet/dry vacuum cleaner beyond that described in this manual. Refer all other servicing to a qualiﬁed service center.

TROUBLESHOOTING

PROBLEM	POSSIBLE CAUSES	SOLUTION
Parts/accessories missing	1. Packed in tank	1. Check in tank
Vacuum cleaner will not start	1. No power at receptacle

2. Defective switch

3. Defective motor

| 1. Check for power

2. Contact Shop-Vac® customer service

3. Contact Shop-Vac® customer service

Dust discharging from exhaust| 1. Filter not installed/not installed properly

2. Filter damaged

3. Filter clogged or dust is too fine

4. Filter not functional

| 1. Properly install filter

2. Replace filter

3. Use more efficient filter

4. Clean or replace filter

Loss of suction| 1. Loose hose connection

2. Filter clogged

3. Full tank

4. Hole in hose

| 1. Tighten hose connection

2. Clean or replace filter

3. Empty tank

4. Replace hose

Static shock| 1. Dry environment

2. Relative humidity of air is low

| 1. Add moisture to air (if practical, use a console or installed humidifier).

2. This situation is temporary and does not affect the use of the vacuum cleaner.

WARNING – IF ANY OF THE MOTOR HOUSING PARTS SHOULD BECOME DETACHED OR BROKEN, EXPOSING THE MOTOR OR ANY OTHER ELECTRICAL COMPONENTS, OPERATION SHOULD BE DISCONTINUED IMMEDIATELY TO AVOID PERSONAL INJURY OR FURTHER DAMAGE TO THE VACUUM. REPAIRS SHOULD BE MADE BEFORE REUSING THE VACUUM.

ONE YEAR INDUSTRIAL/COMMERICAL WARRANTY

One year limited warranty
Shop-Vac® Corporation warrants the vacuum cleaner contained in this package for one year from the date of purchase to correct by repair or parts replacement without charge any product defect due to faulty material or workmanship. Should this product be used for rental service, a 90 day limited warranty will apply. this warranty does Not Cover accesories. Shop-vac® assumes no responsibility for damage or faulty performance caused by misuse or careless handling, or where repairs or modiﬁcations have been made or attempted by others. Proof of purchase date is required. This warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or province to province.

Customers in the United States: for product service contact Shop-Vac® Corporation Customer Service, at 570-326-3557 or go to www.shopvac.com/support. Visit www.shopvac.com for your vacuum’s parts list schematic.
Customers in Canada: for product service return the complete unit, (transportation prepaid), to the Authorized Shop-Vac® Service Centre nearest you. A complete list of Authorized Service Centres is included with each vacuum cleaner.
Customers in Mexico : for product service see paperwork that came with your unit.

SHOP-VAC CORPORATION 2323 Reach Road, P.O. Box 3307 Williamsport, PA 17701-0307 570-326-3557
www.shopvac.com
SHOP-VAC CANADA
1770 Appleby Line
Burlington, Ontario L7L 5P8
905-335-9730 www.shopvac.ca
Shop Vac-México, S.A. de C.V.
Paseo de los Adobes 1081-3
Fraccionamiento Guadalajara Technology Park Zapopan, Jalisco, México C.P. 45019
Patents Issued and Pending.
© 2014 Shop-Vac Corporation. All Rights Reserved.

shopvac 610 WET-DRY VACUUM User Manual

shopvac 610 WET-DRY VACUUM

Description

TOOLS NEEDED

IMPORTANT SAFETY INSTRUCTIONS

GROUNDING INSTRUCTIONS

EXTENSION CORDS

ASSEMBLY

ITEM NUMBER & DESCRIPTION

BAND DOLLY

ITEM NUMBER & DESCRIPTION

SET UP AND OPERATION

FILTER INSTALLATION AND MAINTENANCE

**FILTRATION SYSTEM

DRY PICK UP OPERATION

EMPTYING LIQUID WASTE FROM THE TANK

AUTOMATIC SUCTION SHUT OFF

TROUBLESHOOTING

ONE YEAR INDUSTRIAL/COMMERICAL WARRANTY

References

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Related Manuals