IKEA 603.939.62 LAGAN Stainless Steel Kitchen Hood Instruction Manual

LAGAN

Please refer to the last page of this manual for the full list of IKEA appointed Authorized Service Centre and relative national phone numbers.

Safety Information

Before first use
Your safety and that of others are paramount. Remove cardboard protection pieces, protective film, and adhesive labels from accessories. Check the appliance for any transport damage. To avoid any damage do not place any weights on the appliance. Do not expose the appliance to atmospheric agents. This manual and the appliance itself provide important safety warnings, to be read and observed at all times.
** This is the attention symbol, pertaining to safety, which alerts users to potential risks to themselves and others. All safety warnings are preceded by the attention symbol and the following terms:
DANGER: Indicates a hazardous situation that, if not avoided, will cause serious injury.
WARNING:** Indicates a hazardous situation that, if not avoided, could cause serious injury. All safety warnings give specific details of the potential danger/warning present and indicate how to reduce the risk of injury, damage, and electric shock resulting from improper use of the appliance. Carefully observe the following instructions.

Precautions and general recommendations

• The electrical installation and the electrical connection must be carried out by a qualified technician according to the manufacturer’s instructions and in compliance with the local safety regulations. Do not repair or replace any part of the appliance unless specifically stated in the user manual.

• The appliance must be disconnected from the power supply before carrying out any installation work.
  **WARNING:** Failure to install the screws or fix the device in accordance with these instructions may result in electrical hazards.

• Earthing of the appliance is compulsory. (Not possible for class II hoods identified by the symbol **** on the data plate).

• Do not pull the power supply cable in order to unplug the appliance.

• The electrical components must not be accessible to the user after installation.

• Do not touch the appliance with any wet part of the body and do not operate it when barefoot.

• This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• All other maintenance services must be carried out by a specialized technician.

• When drilling through the wall pay attention not to damage electric connections and/or pipes.

• Air vents must always discharge to the outside.

• The manufacturer rejects all responsibilities for any damage caused by improper use or wrong settings.

• Appropriate maintenance and cleaning ensure good working order and the best performance of the appliance. Regularly clean all stubborn surface dirt to avoid grease buildup. Remove and clean or change the filter regularly. This must be completed in accordance with the “Cleaning and maintenance” instructions provided.

• Never flame cook food (flambé) under the appliance. Using free flames might cause a fire.

• Failure to observe the instructions for cleaning the hood and replacing the filters may result in a fire.

• Exhaust air must not be vented through a flue used for removal of fumes produced by gas combustion appliances or other combustible materials, but must have a separate outlet. All national regulations governing the extraction of fumes must be observed.

• There shall be adequate ventilation if the hood is being used at the same time as other appliances using gas or other combustible materials. The negative pressure of the room must not exceed 4 Pa (4x 10-5 bars). For this reason, ensure that the room is well ventilated. In case of doubts, please consult an authorized service assitance center or similarly qualified person.

• Do not leave frying pans unattended when frying, as the frying oil may catch fire.

• Before touching the light bulbs, ensure that they are cold.

• Do not use or leave the hood without the light bulb correctly fitted, as this may cause electric shock.

• The hood is not a work surface, therefore do not place any objects on top of it or overload it.

• During all installation and maintenance operations wear appropriate working gloves.

• This appliance is not suitable for outdoor use.
  WARNING: when the hob is in use, accessible parts of the hood may become hot.

Installation and connection
In the event of problems, contact the Authorized Service Centre. To prevent any damage, only remove the appliance from its packaging at the time of installation.

Preparing for installation
WARNING: this is a heavy product; the hood should only be lifted and installed by two or more people.
The minimum distance between the hob and the bottom part of the hood must not be less than 65 cm for burning gas or other fuels and 50cm for electric cookers. Before installation also checks the minimum distances stated in the manual of the cooker.
If the installation instructions for the cooker specify a greater distance between cooker and hood, this distance must be observed.

Electrical connection
Make sure the power voltage specified on the appliance rating plate is the same as the mains voltage.
This information can be found on the inside of the hood, under the grease filter. Power cable replacement (type H05 VV-F) must be carried out by a qualified electrician. Contact an authorized service center.
If the hood is fitted with an electric plug, connect the plug to a socket complying with current regulations, located in an accessible place.
WARNING: if no plug is fitted (direct wiring to the mains), or if the socket is not located in an accessible place, a qualified the electrician should install a standardized double pole power switch that will enable complete isolation from the mains in case of category III overvoltage conditions, in accordance with wiring rules.

Use

The hood has been designed to be installed and used either as an “Extraction installation”, or as a “Recirculation installation”.
Extraction installation (see a symbol in the installation booklet)
Cooking steam is sucked and channelled outside the house through a discharge duct (not supplied), fitted to the hood steam outlet.
Ensure that the discharge duct is correctly fitted to the air outlet, unit using an appropriate connection system.
Important: If already installed, remove the charcoal filter/s.

Recirculation installation
(see a symbol in the installation booklet)
The air is filtered through one or more charcoal filters and then resent into the room.
Important: Ensure appropriate air circulation around the hood.
Important: If the hood is supplied without charcoal filters, these must be fitted before the hood can be used. Filters are available in IKEA shops.
The hood should be installed away from particularly dirty areas, windows, doors, and heat sources.
The accessories for wall fixing are not included because walls made of different materials require different types of fixing accessories. Use fixing systems suitable for the walls of your home and the weight of the appliance. For more details, contact a specialized dealer.
Keep this booklet for future consultation.

Product description

1. Control Panel.
2. Grease filter.
3. Lighting unit.

Control panel

A To switch ON the light, push the button
**B** ON/OFF button/Extraction power 1 selection button.
C Extraction power 2 selection button.
D Extraction power 3 selection button.

Cleaning and maintenance

WARNING:
– Never use steam cleaning equipment.
– Disconnect the appliance from the power supply.
IMPORTANT: do not use corrosive or abrasive detergents. If any of these products accidentally comes into contact with the appliance, clean immediately with a damp cloth.

• Clean the surfaces with a damp cloth. If it is very dirty, add a few drops of washing-up detergent to the water. Finish off with a dry cloth.

IMPORTANT: do not use abrasive sponges or metallic scrapers or scourers. Over time, these can ruin the surface.

• Use detergents specifically designed for cleaning the appliance and follow the manufacturer’s instructions.

IMPORTANT: clean the filters at least monthly to remove any oil or grease residuals.
To clean the grease filter
The metal grease filter has an unlimited life and must be washed once a month by hand or dishwasher at low temperatures and with a short cycle. With cleaning in a dishwasher the grease filter may become dull; this does not affect its filtering capacity.

Grease filter maintenance:

1. Unplug the appliance or disconnect the power supply.
2. Remove the grease filters: pull the spring release handle, then remove the filter downwards.
3. After cleaning the grease filter, remount in reverse order ensuring the entire extraction surface is covered.

Charcoal filter maintenance (if the hood is installed in recirculation installation)

1. Pull out the plug or disconnect the power supply.
2. Remove the grease filter
3. If the carbon filters are already fitted (two filters that cover the protective grilles for the motor impeller) and have to be replaced, turn the central handle anti-clockwise to unlock them.
4. Open the two filter shells
5. Pull out the two circular mats
6. Proceed in reverse order to fit the new filters.
7. Refit the grease filters.

Unlike traditional charcoal filters, this charcoal filter can be washed and reactivated.
Care and cleaning long life Charcoal filter

• The anti-odor filter shall be washed and regenerated every 3-4 months (or more frequently if the hood is subject to intensive use), up to a max. of 8 regeneration cycles (in case of particularly intensive use it is recommended that you do not exceed 5 cycles).

Regeneration procedure:

• Wash in the dishwasher at a MAX temperature of 70° or hand wash in hot water without using abrasive sponges (do not use detergents!)
• Wash in the dishwasher at a MAX temperature of 70° or hand wash in hot water without using abrasive sponges (do not use detergents!).
• Dry at a MAX temperature of 70° for 2 hours.

Lamp maintenance

1. Disconnect the hood from the power supply.
2. Open the extractor grille or remove the self-supporting grease filter.
3. Replace the damaged lamp. Use E14 3W max LED lamps only.
4. Refit the extractor grille or grease filter.
   IMPORTANT: make sure you don’t touch the lamp with your bare hands.

What to do if …

presence of mains electrical power.
Turn off the appliance and restart it to see if the faults persist.
The appliance is not connected to the electrical supply| Check if the appliance is connected to the electrical supply.
Turn off the appliance and restart it to see if the faults persist.
The hood’s suction level is not enough| The suction speed is too low| Check the suction speed and adjust as necessary.
The grease filters are dirty 2| Check that the filters are clean
If not, clean the filters in the dishwasher.
The anti-odors filters are dirty| Check that the anti-odor filters are properly washed as recommended
The air vents are obstructed| Check the air vents for any obstructions and remove them as necessary.
The light does not work| The LED is broken 3| For replacement, contact the Authorized Service Centre.

Before contacting the Authorized service center:
Switch the appliance on again to see if the problem has disappeared. If not, switch it off again and repeat the operation after an hour. If your appliance still does not work properly after carrying out the checks listed in the troubleshooting guide and switching the appliance on again, contact the Authorized Service Centre, clearly explaining the problem and specifying:

• the type of fault;
• the model;
• the type and serial number of the appliance (given on the rating plate);
• the Service number (the number after the word SERVICE on the rating plate inside the appliance).

Technical data

The technical information is situated in the rating plate on the internal side of the appliance.

Environmental concerns

Disposal of packing
The packing material is 100% recyclable and is marked with the recycle symbol . The various parts of the packing must therefore be disposed of responsibly and in full compliance with local authority regulations governing waste disposal.

Scrapping the product

• This appliance is marked in compliance with European Directive 2012/19/EU, Waste Electrical and Electronic Equipment (WEEE).
• By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product or on the accompanying documentation indicates that it should not be treated as domestic waste but must be taken to an appropriate collection center for the recycling of electrical and electronic equipment.

Scrapping of household appliances

• This appliance is manufactured with recyclable or reusable materials. Dispose of it in accordance with local waste disposal regulations. Before scrapping, cut off the power supply cable.
• For further information on the treatment, recovery, and recycling of household electrical appliances, contact your competent local authority, the collection service for household waste, or the store where you purchased the appliance.

Energy-saving tips

• Switch ON the hood at minimum speed when you start cooking and kept it running for a few minutes after cooking is finished.
• Increase the speed only in case of a large amount of smoke and vapor and use boost speed(s) only in extreme situations.
• Replace the charcoal filter(s) when necessary to maintain a good odor reduction efficiency.
• Clean the grease filter(s) when necessary to maintain a good grease filter efficiency.
• Use the maximum diameter of the ducting system indicated in this manual to optimize efficiency and minimize noise.

Declaration of conformity
This appliance has been designed, manufactured, and marketed in compliance with:
– safety objectives of the “Low Voltage” Directive 2014/35/EU;
– the eco-design requirements of European regulations n. 65/2014, and n. 66/2014 in conformity to the European standard en 61591 ;
– the protection requirements of Directive “EMC” 2014/30/EU.
The electrical safety of the appliance can only be guaranteed if it is correctly connected to an approved earthing system.

Produced for IKEA:
Factory
IKEA of Swieden AB, PO Box 702, 343 81, Elmhult, Sweden
The importer and the entity authorized by the manufacturer:
LLC “IKEA TORG”, bad. 1, micro rayon IKEA, Khimki, Moscow region, 141400 Russia, tel.: +7(495) 737-5301, fax: +7(495) 737-5324
This device was designed, manufactured, and sold in accordance with the standards of the Customs Union technical regulations, and with local normative legal documents.
Made in Poland
For IKEA product quality issues, contact the seller:
LLC IKEA DOM, bld. 1, micro rayon IKEA, Khimki, Moscow region, 141400 Russia; tel.: +7 495-666-2929, www.ikea.ru
Life cycle: 10 years
Afterlife the cycle is finished, your product can become dangerous. So, after life cycle has been finished, or in case you decided to stop using the product earlier, please address to appropriate officials to legally destroy the appliance”

IKEA GUARANTEE

How long is the IKEA guarantee valid?
This guarantee is valid for 2 years from the original date of purchase of your appliance at IKEA. The original sales receipt is required as proof of purchase. If service work is carried out under a guarantee, this will not extend the guarantee period for the appliance.
Who will execute the service?
IKEA service provider will provide the service through its own service operations or authorized service partner network.
What does this guarantee cover?
The guarantee covers faults of the appliance, which have been caused by faulty construction or material faults from the date of purchase from IKEA. This guarantee applies to domestic use only. The exceptions are specified under the headline “What is not covered under this guarantee?” Within the guarantee period, the costs to remedy the fault e.g. repairs, parts, labor, and travel will be covered, provided that the appliance is accessible for repair without special expenditure. On these conditions, the respective local regulations are applicable. Replaced parts become the property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed Service Provider will examine the product and decide, at its sole discretion, if it is covered under this guarantee.
If considered covered, IKEA Service Provider or its authorized service partner through its own service operations, will then, at its sole discretion, either repair the defective product or replace it with the same or a comparable product.
What is not covered under this guarantee?

• Normal wear and tear.
• Deliberate or negligent damage, damage caused by failure to observe operating instructions, incorrect installation or by connection to the wrong voltage, damage caused by a chemical or electrochemical reaction, rust, corrosion, or water damage including but not limited to damage caused by excessive lime in the water supply, damage caused by abnormal environmental conditions.
• Consumable parts including batteries and lamps.
• Non-functional and decorative parts which do not affect the normal use of the appliance, including any scratches and possible color differences.
• Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap drawers.
• Damage to the following parts: ceramic glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps and lamp covers, screens, knobs, casings and parts of casings. Unless such damages can be proved to have been caused by production faults.
• Cases where no fault could be found during a technician’s visit.
• Repairs not carried out by our appointed service providers and/or an authorized service contractual partner or where non-original parts have been used.
• Repairs caused by installation which is faulty or not according to specification.
• The use of the appliance in a non-domestic environment i.e. professional use.
• Transportation damages. If a customer transports the product to his home or another address, IKEA is not liable for any damage that may occur during transport. However, if IKEA delivers the product to the customer’s delivery address, then damage to the product that occurs during this delivery will be covered by IKEA.
• Cost for carrying out the initial installation of the IKEA appliance.
  However, if an IKEA appointed Service Provider or its authorized service partner repairs or replaces the appliance under the terms of this guarantee, the appointed Service Provider or its authorized service partner will reinstall the repaired appliance or install the replacement, if necessary.

How country law applies
The IKEA guarantee gives you specific legal rights, which cover or exceed all the local legal demands.
However, these conditions do not limit in any way consumer rights described in the local legislation.
The dedicated AFTER-SALES for IKEA appliances
Please don’t hesitate to contact IKEA appointed
After Sales Service Provider to:

• make a service request under this guarantee;

• ask for clarifications on the installation of the
  IKEA appliance in the dedicated IKEA kitchen furniture;

• ask for clarification on functions of IKEA appliances.

To ensure that we provide you with the best assistance, please read carefully the Assembly Instructions and/or the User Manual before contacting us.

How to reach us if you need our service

Please refer to the last page of this manual for the full list of IKEA appointed Authorized Service Centre and relative national phone numbers.

In order to provide you with a quicker service, we recommend using the specific phone numbers listed in this manual. Always refer to the numbers listed in the booklet of the specific appliance you need assistance with.
Please also always refer to the IKEA article number (8 digit code) and 12 digit service number placed on the rating plate of your appliance.

SAVE THE SALES RECEIPT!
It is your proof of purchase and required for the guarantee to apply. The sales receipt also reports the IKEA name and article number (8 digit code) for each of the appliances you have purchased.

Do you need extra help?
For any additional questions not related to After Sales of your appliances please contact your nearest IKEA store call center. We recommend you read the appliance documentation carefully before contacting us.

Coverage for equipment purchased in Russia
This warranty is applicable only to equipment purchased in Russia. The warranty service obligations remain in force only if the item was installed in accordance with the  following requirements:

• the technical requirements accepted in the country where the customer applied for warranty service;
• the safety rules are given in the installation instructions and user manual.

UNITED KINGDOM

Phone number:| 2.08E+09|
---|---|---
Rate:| Local rate|
Opening hours:| Monday – Friday| 8,30am – 6,30pm
| Saturday| 8,30am – 5,30pm
| Sunday| 9,30am – 3,30pm

References

• Møbler, boligtilbehør og inspiration til hjemmet - IKEA
• Hej! Welcome to IKEA Global
• ИКЕА - IKEA

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>