Dakota Alert BBT-2500 Break Beam Transmitter User Guide
- June 5, 2024
- Dakota Alert
Table of Contents
BBT-2500
Break Beam Transmitter
User Guide
PRODUCT DESCRIPTION : The BBT-2500 is used with the DCR-2500 receiver.
The BBT-2500 uses Active Infrared to detect anything that passes through the
sensor pair and breaks both beams at the same time. When the beams are broken,
the unit sends a signal to the receiver. This will sound one of four different
tones (Classical, Westminster Chime, Ding Dong, or Whistle). The BBT-2500 can
be used to monitor access into any area, from your backyard to the lumber yard
and everything in between.
READ MANUAL THOROUGHLY BEFORE INSTALLATION. RETAIN THE MANUAL FOR FUTURE
REFERENCE. FAILURE TO FOLLOW DIRECTIONS PROPERLY MAY RESULT IN DAMAGE.
ONLY use this product for the detection of moving objects such as people
and vehicles.
DO NOT disassemble or attempt to repair the product.
DO NOT install this unit with any other infrared detector. It may cause
false alarms.
DO clean and inspect the unit regularly for proper use. If any problem is
found, contact Dakota Alert, Inc.
WARNINGS: This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause undesired operation.
HARDWARE INSTALLATION
Verify that all installation hardware is included. Tools needed: Phillips screwdriver, adjustable wrench.
PAIRING
To make installation easier it is recommended to pair units ‘A’ and ‘B’ before
mounting.
On a flat surface push the power button (Figure 1-1) on ‘A’ then push the
power button on ‘B’. Laying the units flat on a counter or table, line up the
infrared light holes (Figure 1-2). The units will then pair. You will see
lights flashing during this process. Leave the units in place for one minute
to make sure this process is complete.
Once paired, test them by completely blocking all 3 holes (2 infrared light
holes and an indicator hole shown in Figures 1-3). The unit should send a
signal to the DCR-2500 and
sound an alert. The unit will only alert if all 3 holes are completely blocked
for at least 100ms. If an object passes through the beam faster than that it
will not be detected. ‘A’ unit contains the radio transmitter module. The ‘A’
unit transmitter module is factory set to match the zone 2 setting of the
DCR-2500. It is not recommended to change the code setting unless it is needed
to avoid interference or a different zone is desired. Be careful when
opening this unit to avoid damaging any internal components or wires. ‘B’
unit contains no user-serviceable parts. It is not recommended to open this
unit.
| |
---|---|---
Below are the two most common mounting options.
CIRCULAR POST MOUNTING
1). Take the right angle bracket (Figure 3-1) and attach the cross bracket
using (2) M4 nuts and (2) M4x12mm screws. Repeat for all brackets.
2). Using (2) M5 nuts and (2) M5x18mm screws attach the right angle bracket
(Figure 3-2) to units ‘A’ and ‘B’. 3). Attach to post with ‘U’ shaped bracket
(Figure 3-3). Using (2)
M5 nuts and (2) M5x27mm screws attach ‘U’ bracket around the post. Tighten
securely.
FLAT SURFACE MOUNTING
1). Using (2) M5 nuts and (2) M5x18mm screws attach the right angle bracket
(Figure 4) to units ‘A’ and ‘B’.
2). Use screws that are appropriate for your material and surface (not
included) and mount right angle bracket taking care to keep units ‘A’ and ‘B’
level.
MOUNTING OUTSIDE
Units ‘A’ and ‘B’ can be mounted up to 300’ apart. Determine the height and
location you would like to mount the unit. Recommended height is 3-4’. There
must be a line of sight between ‘A’ and ‘B’. Units must be mounted level.
Install the unit on a stable surface. Do not install where trees or other
objects can block the beam. Mounting 3-4’ will avoid false alerts by small
animals crossing under the beam, but still, detect people and vehicles. Mount
unit ‘B’ first and face the infrared holes toward where unit ‘A’ will be
mounted.
When mounting unit ‘A’, face the infrared holes towards unit ‘B’. When the
units align there is an audible click in unit ‘A’.
To make sure of proper alignment cover only the top two infrared holes. The
unit should not be alert. Then cover only the bottom two holes, again unit
should not alert. Cover all three holes and the unit should alert. If the unit
alerts with only the top two infrared holes covered, raise the unit about an
inch to correct misalignment. If the unit alerts with only the bottom two
infrared holes covered, lower the unit about an inch. When properly aligned,
the unit will only alert when all three infrared holes are covered.
FOR ALL MOUNTING SITUATIONS
In all mounting situations, it is very important that the ‘A’ unit only
interacts with one ‘B’ unit or the pair may not alert properly. Use the
diagrams below for reference.
STRAIGHT LINE MOUNTING (900 feet)
PERIMETER MOUNTING
ONLY OPEN UNIT ‘A’ IF CHANGING THE ZONE/CHIME IS ABSOLUTELY NECESSARY. It is not recommended to change any settings as the BBA-2500 is factory set to match.
DO NOT OPEN UNIT ‘B’.
Remove the 8 screws on the back of unit ‘A’ (Figure 5-1). Gently lift the solar panel to expose the transmitter board (Figure 5-2). Locate the 10 dip switches on the red block. The first eight dip switches are for the frequency setting (256 combinations). Set switches 1-8 to match the eight switches in the receiver. Switches 9 and 10 are for the zone/channel settings on the transmitter. The four zones are listed in the table below.
Switch 9 | Switch 10 | Channel | Tune |
---|---|---|---|
On | On | 1 | Classical |
Off | On | 2 | Westminster |
On | Off | 3 | Ding Dong |
Off | Off | 4 | Whistle |
Coding the DCR-2500 receiver:
Open the receiver case by inserting a small screwdriver into one of the pry
notches on the side of the case (refer to receiver manual). Gently lift off
the front cover. Locate the eight dip switches on the DCR-2500 and make sure
they are set identically to dip switches 1-8 on the BBT-2500.
Note: If more than one transmitter is used with the receiver, the first
eight dip switches of all transmitters must match the eight dip switches of
the receiver.
Note: Whenever a change is made to the time jumper or the dip switches,
the receiver must be turned OFF and then back ON to operate properly.
TROUBLESHOOTING:
If sensor pair alerts when originally paired, but will not alert when mounted…
- Push the power button on unit ‘A’
- Look in the center hole for the indicator light. If the light is on, proceed to step 3. If the light is not on, press power button again. Indicator light should come on.
- Repeat steps 1 and 2 for unit ‘B’. This will re-sync the units.
If experiencing false alerts…
- Check for obstruction (i.e. branch, frost)
- Extreme fog
- Extreme snow and rain
- If obstruction/weather are not involved, try changing the frequency of the DCR-2500 and unit ‘A’
- If a unit is blocked continually a second signal will be generated after one hour
If no signal…
- Turn power off on all units for 60 seconds and then turn the power back on
- Make sure units are still aligned
- Make sure all 8 dip switches in DCR-2500 match the first 8 dip switches inside unit ‘A’
TECHNICAL SUPPORT : If you encounter any difficulty in the operation of this product after reading the manual, please contact Dakota Alert. You can reach us by phone at 605-3562772 from 8:30 AM to 5:00 PM Monday through Friday (Central Standard Time). We will be happy to answer your questions and help you in any way we can.
WARRANTY: Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, the act of God, or improper operation. If this product does become defective, simply return it to Dakota Alert. Please include a note describing the troubles along with your name and return address as well as the original sales receipt. If the product is covered under warranty it will be repaired or replaced at no charge. If it is not covered by warranty, you will be notified of any charges before work is done.
Marketed by
1800doorbell.com,
Manufactured by Dakota
Alert, Inc.
32556 E. Main Street
P0 Box 130
Dakota Alerts
Warranty Info
Phone: 605-356-2772
Fax: 605-356-3662
References
- Door Chimes for Business | Doorbells | Driveway Alert Kits
- Door Chimes for Business | Doorbells | Driveway Alert Kits
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>