BOKMAN VA-IH006 5.5 Full HD 1080p Baby Monitor User Guide

BOKMAN VA-IH006 5.5 Full HD 1080p Baby Monitor

SAFETY INSTRUCTIONS

• Keep cord out of the reach of children (more than 3ft / 0.9m away) in case of STRANGULATION.
• NEVER place the camera or cord in or near the crib or playpen.
• NEVER mount the camera directly above the crib or playpen to avoid the risk of injury.
• Only use the AC adapters provided.
• Never use the unit near water, including near a bathtub, sink, laundry machine tube, wet basement, etc.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other devices that produce heat.
• Only use attachments and accessories specified by the manufacturer.
• Unplug this device when unused for long periods of time.
• Do not insert anything into the upgrade pinholes. This operation is only intended for professionals.

CAUTION

• NOT toys. Do not allow children to play with them.
• The lens and lens hood are small parts, keep them out of your baby’s reach at all times.
• This product is NOT intended to replace the proper supervision of children. You MUST check your child’s activity regularly.
• This product is not intended for use as a medical camera and its use should not replace adult supervision.
• Unplug the product during lightning storms.
• Please check the operating range and condition of the camera carefully at the initial installation, and on a regular basis after that.
• Check the reception regularly. Test the camera before use and after changing the camera’s location.
• For indoor use only.
• Clean the camera with a dry cloth only.
• Do not block any ventilation openings.
• Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.

PACKAGE CONTENTS

• Baby Monitor & Camera (Model: VA-IH006)
• Monitor Adapter with USB-C Charging Cable
• Camera Adapter
• USB-C Charging Cable
• Quick Start Guide
• User Guide

PRODUCT DIAGRAM

Baby Monitor

1. Antenna
2. USB-C Port
3. On/Off Button
4. Menu Button
5. Power Indicator
6. Charging Indicator
7. Zoom Button
8. Left Button
9. Up Button
10. Right Button
11. OK Button
12. Down Button
13. Talk Button
14. Power Button
15. Short Cut
16. Back Stand
17. Speaker
18. Reset Pinhole

Camera

1. Camera Antenna
2. Camera Vents
3. Lens
4. Mounting Hole
5. Reset Pinhole
6. Temperature Sensor
7. Speaker
8. USB-C Charging Cable

GETTING STARTED

Charging & Powering Baby Monitor 

1. Connect the monitor adapter to the monitor and a power outlet.
2. Unplug the unit when its power indicator turns off, indicating a full charge.
3. Press the Power button on the monitor to power on with the power indicator lighting green.

Powering Camera
Connect the camera to power source via the USB-C Charging Cable and camera adapter.

• Only use the power adapters included in the package.
• Do not place the camera and power cord within the reach of your baby.

Pairing the Baby Monitor & the Camera
By default, one camera has been paired with the monitor when manufactured. When you power on the monitor and camera, the two will automatically pair. To add more cameras, press the Pair Button at the bottom of the camera, press Menu button, select through > > , and then the monitor will auto-pair with the camera.

• Once they’re paired successfully, the camera number with icon will be shown at the top left.
• Microphone feedback might occur when the monitor is too close to the camera. Please keep them at least 1.5m / 4.9ft apart.
• It is recommended to pair in the baby’s room, or wherever you intend to place the camera.

Placing the Camera
Place the camera 1.5-2m / 4.9-6.6ft away from your baby for safety reason and for a better view when in night vision mode.

Wall Mounting Camera

1. Select the spot to mount the camera, keeping it beyond your baby’s reach.
2. Insert the screw (not included) pre-installed on wall into the mounting hole of the camera.

It’s strongly recommended to use a screw and screw anchor. Don’t release the camera until you’re sure it is firmly mounted.

FUNCTIONS & OPERATIONS

Monitor Interface Overview

Top Status Indications

Bottom Menu Brief

Monitor Settings
Press Menu Button, Left and Right Buttons, and then OK Button to set the monitor:

1. Time setting: Set the current time by setting hour, minute, and AM/ PM.
2. System sound volume: Select between Low, High, and Mute.
3. Temperature scale: Select between °C and °F.
4. Screen auto-sleep time: Select between 1min, 2min, 5min, and OFF.
5. Restore to factory settings: Press OK Button to confirm resetting; “Restoring factory settings” will be shown when restoring, and you can’t press any button to control the device during this period. The monitor will auto restart when it’s done.
6. Customer service contacts: Check the email, Tel. number, and address for customer service.

Talkback
Press and hold Talk Button to talk to your baby, release it to exit the talking mode. When you enter the talking mode, the icon will be shown on the monitor. When it’s mute or the speaker volume is too low, you may not be able to hear the baby. When you’re pressing the Talk Button, the camera will not transfer the sound to the monitor. Please release the button to listen to your baby.

Temperature Alert
The monitor will prompt too high (>35°C / 95°F) and too low (<0°C / 32°F) temperatures with the “HH” and “LL” icon, accompanied with a icon and a beep alert. When the monitor is mute, you may not be able to hear the baby.

SPECIFICATIONS

Monitor

Zoom In (4X)
Two-Way Talk| Yes
Multi-Camera| Max. 2 cameras
Storage Temperature| -10°C ~ 55°C / 14 – 131°F
Operation Temperature| 0°C ~ 40°C / 32 – 104 °F

camera

169 degrees horizontal (Left=135, Right=135)
Zoom| Zoom In (2X)
Zoom In (4X)
Lens Focal Length| 1.5m to infinity
Night Vision| Black & White image, up to 2m clear range
IR LED| Non-visible IR LED with wavelength 940nm (x 12 pcs)
Light Sensor| Yes
Two-Way Talk| Yes
Storage Temperature| -10°C ~ 55°C / 14 – 131°F
Operation Temperature| 0°C ~ 40°C / 32 – 104 °F

TROUBLESHOOTING

Product not powering on?

| · Check that the camera and monitor are turned on.

· Check the camera is connected to power properly (it cannot be charged; it’s power off once disconnected from power).

· Check that the monitor is of enough battery (it’ll auto shut off when battery level icon flashes red slowly on the monitor).

---|---

Baby monitor can’t connect with the camera?

| · Check whether the camera is near the monitor (recommended to keep within 1.5-2m / 4.9-6.6ft).

· Check whether the monitor is of low battery. Charge it in time to restore good connection.

· Check whether the camera is well connected to power.

· Check whether there are any large metallic objects including doors, refrigerators, mirrors, etc., are placed between the camera and monitor thus blocking the radio signals.

· Check, whether there’s any other 2.4GHz product, is used nearby like WiFi routers, and microwave ovens, which may interfere the connection.

· If nothing above is involved, please retry to pair:

Press and hold the OK button on monitor to enter pairing mode, and the monitor will connect with the camera nearby automatically.

Nothing shown when I view a camera?

| · Check all connections to the camera (power cable plugging and pairing).

· Check whether the screen is in sleep mode. Press any button to awake it.

· Check whether the camera is within range of the monitor.

· Adjust the monitor antenna to vertical position for better signal transfer.

No sound from the monitor?| · Check whether the system sound volume is set High or Low. It’ll be mute if set so.
---|---
Black and white pictures?| Night vision LED may be ON. Please turn on room lights to force it out of the night mode.

Choppy videos?

| · Check whether the camera is near the monitor and that there’re no obstacles between them.

· Adjust the monitor antenna to vertical position for better signal transfer.

Too much noise?

| · Volume may be set too high. Press Menu Button -> OK Button -> Left Button to volume down.

· The camera and monitor may be put too close; keep them at least 1.5m / 4.9ft apart.

· The camera may be too out of range. Please keep it within 10m / 32.8ft to the monitor.

FCC STATEMENT

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC 20cm Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC STATEMENT
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

References

• VAVA Official Site - Evolve

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>