MILLITRONIC MG360 Wireless WiGig Router User Manual

MILLITRONIC MG360 Wireless WiGig Router

Connection

• Step1:
  Connect Display and camera by hdmi and usb cable form PIKA-CONN

• Step2:
  Let PIKA-CONN and laptop in the same wireless area network ( Router)

• Step3:
  Laptop connect to Router

• Step4:
  Enable Millitronic APP, you can screen cast to display, and turn on the web cam
  Caution:

  • 5GHz band (W52): Indoor use only (except communicate to high power radio)

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device is restricted for indoor use.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

IMPORTANT NOTE:

• This module is intended for OEM integrator. This module is only FCC authorized for the specific rule parts listed on the grant, and that the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
• Additional testing and certification may be necessary when multiple modules are used.
• 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied.
• Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

USERS MANUAL OF THE END PRODUCT:

• In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied.
• The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate this equipment.
• This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

LABEL OF THE END PRODUCT:

• The final end product must be labeled in a visible area with the following ” Contains TX FCC ID: 2AJAS9WPIKA010901″.
• This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.

Ant List

Ant.

| ****

Port

| ****

Brand

| ****

Model Name

| ****

Antenn a Type

| ****

Connector

| Gain (dBi)
---|---|---|---|---|---|---
5G

Band 1

| 5G

Band 4

1| 1| Millitronic| 5SN0000

00007

| PCB

Antenna

| I-PEX| 4.11| 3.51
2| 2| Millitronic| 5SN0000

00007

| PCB

Antenna

| I-PEX| 4.11| 3.51

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>