PHOENIX CONTACT 1090747 Thermomark Go Thermal Transfer Printer Instruction Manual

PHOENIX CONTACT 1090747 Thermomark Go Thermal Transfer Printer

Startup of the THERMOMARK GO thermal transfer printer

The THERMOMARK GO is a portable thermal transfer printer for industrial use. The thermal transfer printer prints materials for marking electrical components.

• Die-cut labels
• Continuous labels
• Shrink sleeves
• Cable markers

The THERMOMARK GO uses special material cartridges that contain the material as well as the corresponding ink ribbon. Only use material cartridges that are provided for the THERMOMARK GO by Phoenix Contact.

Safety notes

Hazard to operational safety

• Incorrect operation or modifications to the device can endanger your safety or damage the printer. Repairs must only be carried out by Phoenix Contact.
• This device is not suitable for use at locations where children might be present.
• There is a risk of explosion, fire, and danger to health if the batteries are used incorrectly.
  • Only use dry batteries in proper condition. Only the sup­plied battery is suitable for battery operation (THERMOFOX/ACCU, 0805009).
• Never damage the batteries (e.g., by throwing, pressing on the battery or using sharp objects). Never expose the batter­ies to high levels of heat (e.g., caused by fire or sunlight). Never let the batteries come in contact with moisture or salt water.
• Pay attention to the correct polarity when inserting the bat­teries.
• Only charge the battery in the THERMOMARK GO or in the provided charger (THERMOFOX/CHARGER, 0805012). Do not use any other chargers, e.g., cigarette lighter socket in the car.
• Temperature range when charging the battery: 0°c … 45°C
• Store the battery separately in a dry and cool place.
• Never expose batteries to extremely low air pressure.

Damage to the device

• Do not operate the printer near high-voltage lines.
• Only operate the printer in a dry location protected from spray.
• Protect the printer and printing materials from humidity, moisture and dirt.
• Only connect the printer to systems that have a protective extra-low voltage.

Overview

1. NFC area
2. On/off switch
3. Cutter
4. Bluetooth reset
5. Open material compartment
6. Socket for power supply unit
7. Socket for USB connection
8. Battery compartment
9. Compartment for material cartridge

Connecting the power supply

The THERMOMARK GO can be supplied with power in differ­ent ways.

• Batteries (6 xAA alkaline)
• AC wide-range power supply unit (THERMOFOX/ADAPTER, 0805010)
• Battery (THERMOFOX/ACCU, 0805009)

If the THERMOMARK GO is connected to the power supply via the power supply unit, the battery in the THERMOMARK GO is automatically charged. The battery can also be charged using an external charger (THERMOFOX/CHARGER, 0805012).

Connecting the power supply unit

The THERMOMARK GO is designed for power grids from 100 V to 240 V AC.

• Slightly tilt the relevant adapter and place it onto the front side of the power supply unit and press the adapter down.
• To remove the adapter, pull the slider on the base element in the direction of the cable.

Inserting the batteries

WARNING: Explosion hazard

• Only use batteries of the stated type. Using incorrect types may disable protective measures.

WARNING: Risk of fire

Only operate the device if the battery cover is closed correctly. Combustible material close to the battery compartment may ignite.

• To open the battery compartment, push the interlock of the cover into the direction of the connections.
• Insert the battery with correct polarity and slightly tilted into the battery compartment.
• Press down the battery.
• Close the cover.

Insert the material cartridge

• To open the material compartment, push the green button.
• Keeping the material cartridge straight, insert it into the com­partment from the side so that it engages with a click.
• Make sure that the material end is in the output tray.
• To remove the material cartridge, pull it sideward while keeping it straight.

NOTE: Damage to the printer and material car­ tridge.

• If the printer is not going to be used for a prolonged period of time, remove the material cartridge from the printer.

Operation

For detailed operating instructions, refer to: phoenixcontact.net/qr/1090747.

Installing the MARKING system app

• Install the “MARKING system app” via the Apple App Store or the Google Play Store.
• Open the app. If you place your mobile terminal device on the NFC area of the printer, the app opens automatically.
• Establish a connection to the printer.

There are two options

• Connect the printer to your PC with a USB cable.
• Connect the printer to your mobile terminal device via Bluetooth.

Bluetooth

• Enable Bluetooth on your mobile terminal device.
• The connected printers and their ID are shown in the app.
• The ID can be seen on the printer display (e.g.. TMGO 0000).

Cleaning the print head and pressure roller

Clean the print head and pressure roller regularly.

NOTE: Damage to the print head.

• Do not touch the protective glass of the print head With your fingers or sharp objects.
• Clean the print headline (1) and pressure roller (2) with a felt stick (e.g., CLEANING STICK, 5146697) soaked in isopropyl alcohol.
• Allow the print head to dry for two to three minutes.

Disposal

• The device contains valuable recyclable materials, which should be utilized.
• Dispose of the printer separately from other waste, i.e., via an appropriate collection site.
• Dispose of the battery separately from other waste, i.e., via an appropriate collection site.

FCC Supplier’s Declaration of Conformity

PHOENIX CONTACT I THERMO MARK GO

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. PHOENIX CONTACT I 586 Fulling Mill Road Middletown, PA 17057 I 800-888-7388

Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against ham,ful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>