Sena TECHNOLOGIES SP82 Latitude Helmet User Manual
- June 5, 2024
- Sena Technologies
Table of Contents
TECHNOLOGIES SP82 Latitude Helmet
User Manual
SP82 Latitude Helmet
Charging
Red LED: Charging Blue LED: Fully charged
Power On/Off
Power On: Press and hold the Jog Dial and Phone Button for 1 second
Power Off : Tap the Jog Dial and Phone Button.
Volume Adjustment
Increase/Decrease the volume: Rotate the Jog Dial clockwise or
counterclockwise
Battery Check
Phone, Music Pairing
Initially Pairing the Latitude S1
The Bluetooth system will automatically enter the phone pairing mode when you
initially turn on the Bluetooth system or in the following situation:
• Rebooting after executing Factory Reset
- Press and hold the Jog Dial and Phone Button for 1 second.
- Search for Bluetooth devices on your mobile phone. Select Latitude S1 in the list of the devices detected on the mobile phone.
- Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press and hold the Jog Dial for 1 second.
Track forward/ back: Rotate while pressing the Jog Dial clockwise or
counterclockwise.
Mobile Phone Call Making and Answering
Answering a call: Tap the Phone Button
Ending a call: Tap the Phone Button
Voice dial: Tap the Phone Button
Rejecting a call: Press and hold the Jog Dial for 2 seconds.
Intercom
Intercom Pairing
- Press and hold the Jog Dial of two headsets for 5 seconds until the red LEDs of both units start to flash rapidly.
- Simply tap the Jog Dial of any one of the two headsets.
Intercom Start/End: Tap the Jog Dial.
Setting
Configuration Menu: Press the Jog Dial for 10 seconds.
Troubleshooting
Factory Reset
If you want to restore the headset to factory default settings. Press and hold
the Phone Button for 10 seconds and tap the Jog Dial. The headset
automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antennae
- Increase the separation between the equipment and the receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
The highest SAR value reported under this standard during product
certification for use next to the head with the minimum separation distance of
10mm is 0.287/Kg. This transmitter must not be collocated or operating in
conjunction with any other antenna or transmitter. This product is in
compliance with FCC RF exposure requirements and refers to the FCC website
https://apps.fcc.gov/oetcf/eas/reports/GenericSearch.cfm search for FCC
ID: S7A-SP82, IC:8154A-SP82.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- This device may not cause interference, and
- This device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>