CHAINBOX SR-ZG2819S ZigBee Dim Remote Instruction Manual

SR-ZG2819S
ZigBee Dim Remote
Instruction Manual
09.ZG2819S.04841

Important: Read All Instructions Prior to Installation.

Function introduction

Product Data

• ZigBee Dim remote based on ZigBee 3.0
• Enables to control single color lighting devices
• High sensitive & high stable touch color wheel, fast & precise color control
• Battery-powered remote with low power consumption
• Enables to pair ZigBee lighting devices through touchline commissioning
• Supports find and bind mode to pair with ZigBee lighting devices
• Supports 4 groups for binding max. 30 lighting devices
• 2.4 GHz global operation
• Transmission range up to 30m
• Compatible with universal ZigBee Gateway products
• Compatible with universal single-color ZigBee lighting devices

ZigBee Clusters Supported by This Remote Are As Follows:
Input clusters:

• Basic
• Power Configuration
• Identify
• Diagnostics

Output clusters:

• Identify
• Group
• Scene
• On/off
• Level control
• Ota

Safety & Warnings

• This device contains AAA batteries that shall be stored and disposed of properly.
• DO NOT expose the device to moisture.

Operation

1. This ZigBee Dim remote is a wireless transmitter that communicates with a variety of ZigBee compatible systems. This transmitter sends wireless radio signals that are used to remotely control a compatible system.

2. This ZigBee remote supports 4 groups for binding max. 30 lighting devices and enables to control single color ZigBee lighting devices.

3. Zigbee Network Pairing through Coordinator or Hub (Added to a Zigbee Network)

4. TouchLink to a Zigbee Lighting Device Note
   1) Directly TouchLink (both not added to a ZigBee network), each remote can link with 30 devices.
   2) TouchLink after both are added to a ZigBee network, each remote can link with max. 30 devices.
   3) For Hue Bridge & Amazon Echo Plus, add remote and device to the network first then TouchLink.
   4) After TouchLink, the remote can control the linked lighting devices.

5. Removed from a Zigbee Network through Coordinator or Hub Interface

6. Factory Reset Manually

7. Remove a Touchlink Paired ZigBee Lighting Device

8. Factory Reset a Lighting Device (Touch Reset)
   Note: the device shall be added to a network, the remote added to the same one or not added to any network.

9. Find and Bind a Zigbee Lighting Device
   Note: Make sure the device and remote are already added to the same Zigbee network.

10. Find and Unbind a Zigbee Lighting Device

11. Clear All Find and Bind Mode Paired Lighting Devices of a Group

12. Setup a Network & Add Devices to the Network (No Coordinator or Hub Required) Step 6: Add more remotes to the network as you would like.
    Step 7: Factory reset the lighting devices that you would like then add them to the network, refer to their manuals.
    Step 8: Touch the link to pair the added remotes and lighting devices, refer to their manuals. Each remote can link with max. 30 lighting devices. Each lighting device can be linked by max. 30 remotes.

13. OTA
    The remote supports firmware updating through OTA and will acquire new firmware from the Zigbee controller or hub every 10 minutes automatically.

14. How to Check Whether the Remote Belongs to a Network or not
    Activate the remote by clicking the All On/Off button (indicator on), then short press any other buttons except group buttons, indicator blinking 3 times means the remote does not belong to any network, blinking once or twice means it has already been added to a network.

15. Battery Power Monitor Function
    The remote will report battery power value to the coordinator under the following situations:
    • When powered on.
    • When short press both S2 and S3 buttons simultaneously.
    • When operating the switch to send data packets (over 4 hours since the last operation).
    • When added to the network by a coordinator.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>