Shenzhen Xinfengweiye Technology U850 4G Wireless Router User Manual

Shenzhen Xinfengweiye Technology U850 4G Wireless Router

Introduction

Appearance

• The above pictures are for reference purposes only.

Features

This device supports FDD-LTE/WCDMA frequencies, it provides high-speed 4G & 3G network sharing service for clients such as Smartphones, PCs etc.

Indicators Description

After the device is connected fully, the computer will install the driver automatically, then users can use wifi hotspot normally.

Signal Indicators – (Red)

• Red light ON means haven’t insert any SIM card or no signal.
• Red light flashing means signal unstable, signal strength lower than 40%.
• Red light OFF means signal is stable.

Internet Indicator – (Blue)

• Blue light OFF means disconnect data.
• Blue lights ON means connect data under 4G network.
• Blue lights flashing means connect data under 3G network.

Wi-Fi Indicator – (Green)

• Slow green light flashing means no users are connected.
• Quick green light flashing means user connected, data is in use.
• The green light on means user connected, no data used.

PC Connect Internet By 3G/4G

If the computer does not equipped with any wireless card, the user should install driver according to the tips in USB connection.
Remark

1. If the system does not support CD ROM automatic installation after the device is connected to the computer, please run the CD ROM driver in My Computer and start manually software installation.
2. If fail to automatic installation, please check if the antivirus and security software open or not, if open, please close the software and start installation.
3. After the driver installed successfully, but failed to identity the device as a dongle in the computer with USB connected, please refer to the below and check whether the computer open “AutoRun” or not.
4. In Windows 7, click”Start”, -> “Control Panel” -> “Hardware and Sound”-> “Auto Run”, please check “use Auto Run for all the media and devices (U)” open or not.
5. In Windows XP, click “Start” -> “Run”, enter “gpedit.msc” and run, then click “Group Policy”, and open “Computer Configuration” under the “Local Computer Policy” , -> “Administrative Templates” -> “System”, and check on the right “Setting” whether “AutoRun” open or not.

System requirements

Windows

• Supports Windows XP 32bit/64bit
• Vista 32 bits/64bits
• Windows 7 32bit/64bit
• Windows 8

Mac

• Mac 10.6 and above, the highest version is Mac 10.9

Browser

• Internet Explorer 7.0 and above
• Safari 4.0 and above

Connect Internet Via Wi-Fi

When the users connect the device for the first time, it will required to enter an SSID and password, You can get the information through the following method.
Check default Wi-Fi Key through the device label

Tips: For your Wi-Fi safety, please log in the Web UI page to set a high safety Wi-Fi password.

Managing the Web UI Page

Account management

Please login the management page according to the below method:

1. Start the browser, enter http://192.168.0.1 into the webpage in address bar. If the IP address has conflict with the other IP address, the device will auto update new IP address.
2. Enter your password and login the management page, the default password is admin.
3. After entering the management page, you can use SMS, Phonebook, SD card, Advance setting, Quick Setting functions.
   Tips : click on the above right to change the login password

Wi-Fi Connection

Enter into the Network setting and click on Wi-Fi settings, then you can get the Wi-Fi password. Main SSID and guest SSID can support 10 Wi-Fi users online simultaneously.

Data Management

Click on Data Management and enter into, then you can set the daily, monthly statistic plan. As shown, you can create a flow plan and apply.

Data Management
Flow management interface shows current internet upload, download speed, current time usage statistic and connection time, current month total statistic usage and connection time.

Connection Settings

Use the “Automatic” network configuration will pop-up a network selection list, it contains all searching network, user can select the available one, and the device will register to the selected network.

APN Settings

In Automatic mode, the relevant information on the APN will be automatically adapted according to the inserted SIM card.

Precautions

• Please use accessories only from the original factory or approved factories. Using any unauthorized accessories will affect the performance of this device, and will be against product warranty terms and related national regulations about communication terminal products.
• Avoid use this device near metal structure or devices that emit electromagnetic waves, otherwise it will affect signal acceptance.
• this device is not water proof. please keep it dry and store it in dry and cool environment.
• Please do not use the device in areas where the temperatures fluctuates rapidly, as this could allow condensation to form on the exterior of the device. If this does occur, please wait for sometime until the condensation disappears before using the device
• Please handle the devide with care. Do not drop, bend or bump the device, as doing so may cause irreparable damage to the device.
• unqualified persons are prohibited from disassembling this device. When repairs are required, please go to designated repair place for maintenance. Only qualified technicians should attempt to repair this device.
• The suggested using environment is 0℃～35℃, the relative humidity should be between 5％～95％.

Installation method

Installation of the Micro-SIM card

• As shown in the below picture, please insert the SIM card and SD card accordingly
• When install the SIM and SD card, please open the back of the device and remove it, insert the Micro-SIM card and SD card into the slot according to the direction of the arrow. After installation successfully, put the cover back on the device and close it.

Package Contents

• 1 * USB Dongle

Warning

FCC RF EXPOSURE INFORMATION

WARNING!! Read this information before using your 4G Wireless Router In August 1986 the Federal Communications Commission (FCC) of the United States with its action in Report and Outer FCC 96-326 adopted an updated safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted by FCC regulated transmitters. Those guidelines are consistent with the safety standard previously set by both U.S. and international standards bodies. The design of this 4G Wireless Router complies with the FCC guidelines and these international standards. Use only the supplied or an approved antenna. Unauthorized antennas modifications, or attachments could impair call quality, damage the 4G Wireless Router, or result in violation of FCC regulations. Do not use the 4G Wireless Router with a damaged antenna. If a damaged antenna comes into contact with the skin, a minor burn may result. Please contact your local dealer for replacement antenna.

BODY-WORN OPERATION
This device was tested for typical body-worn operations with the back/front of the 4G Wireless Router kept 5mm from the body. To comply with FCC RF exposure requirements, a minimum separation distance of 5m m must be maintained between the user’s body and the back/front of the 4G Wireless Router, including the antenna. Third-party belt-clips, holsters and similar accessories containing metallic components shall not be used. Body-worn accessories that cannot maintain 5m m separation distance between the user’s body and the back/front of the 4G Wireless Router, and have not been tested for typical body-worn operations may not comply with FCC RF exposure limits and should be avoided.
For more information about RF exposure, please visit the FCC website at www.fcc.gov
Your wireless handheld portable 4G Wireless Router is a low power radio transmitter and receiver. When it is ON, it receives and also sends out radio frequency (RF) signals. In August, 1996, the Federal Communications Commissions (FCC) adopted RF exposure guidelines with safety levels for hand- held 4G Wireless Router. Those guidelines are consistent with the safety standards previously set by both U.S. and international standards bodies: