i-SYNERGY N240600 Lithium-ion Batteries Instruction Manual
- June 5, 2024
- i-SYNERGY
Table of Contents
Operator Manual
Lithium-ion Batteries Manual
Model:N240130
Model:N240600
SAFETY PRECAUTIONS
All operators should read, understand and exercise the following safety precautions. Any damage caused by misuse or unauthorized persons will void the warranty.
1. Do not dismantle the batteries.
WARNING: Dismantling batteries may cause short-circuit. Which can result in explosion or fire. Moreover, dismantling batteries may cause the leaking of electrolyte. If electrolyte gets into your eyes or any part of your body, please wash with a large amount of fresh water and see a doctor immediately.
2. Do not over discharge the batteries.
3. Do not short-circuit the batteries.
4. Do not punch or press the batteries. Do not put heavy objects on the
batteries.
5. Keep the batteries away from fire and flammable objects, keep the
batteries dry.
6. Do not cover the batteries with any electroconductive objects.
SPECIAL ATTENTION
1. During the charging process, if there is any abnormal smell or sound,
please stop charging the batteries immediately.
2. During the usage process, if there is any abnormal smell or sound,
please stop using the batteries immediately.
3. Don’t dismantle the batteries if error occurs, contact your distributor
as soon as you can.
4. Don’t use organic solvent to clean the batteries, if the battery
catches fire, use carbon tetrachloride extinguishers or sand, do not use
carbon dioxide extinguishers.
5. After the batteries discharge, the batteries must to be charged in
time. If you don’t use the batteries for a long time, please charge once every
month at least.
BATTERY COMPONENTS
- Communication Interface
- Cells balance,battery maintenance
- Battery positive
- Battery negative
- Reset button
909099090909090909090
N240600
- Reset button
- Communication Interface
- Cells balance,battery maintenance
- Battery positive
- Battery negative
N240130
TECHNICAL SPECIFICATIONS
ITEM | PARAMETRIC |
---|---|
N240130 | N240600 |
SIZE | 376x340x253mm |
NOMINAL CAPACITY | 120Ah |
NOMINAL VOLTAGE | 24V DC |
MAX. OUTPUT CURRENT | 60A |
CHARGER INPUT | AC100V~240,50/60Hz |
CHARGER OUTPUT | 15A |
CHARGING TIME | ≤ 10h |
WEIGHT | 31KG |
CHARGING ENVIRONMENT TEMPERATURE | 0 ~ 45 ℃ |
APPLYING ENVIRONMENT TEMPERATURE | -5 ~ 55 ℃ |
STORAGE ENVIRONMENT TEMPERATURE | -10 ~ 65 ℃ |
BASIC TROUBLE SHOOTING
PROBLEM | SOLUTION |
---|---|
CHARGING AND DISCHARGING ERROR | 1. CHECK WIRING |
2. CHECK BATTERY OUTPUT VOLTAGE
3. CHECK CONNECTION
4. DISCONNECT LOAD BEFORE RECONNCETING
5. PROTECTION BOARD ERROR ,PRESS”RESET”
OVER – HEATING DURING OPERATION| 1. MAX. OUTPUT CURRENT IS EXCEEDED
2. LOOSE CONNECTION
FCC WARNING
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Any changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
NEXT BATTERIES