HANSONG BM240 Amplifier Box User Manual

June 5, 2024
HANSONG

HANSONG BM240 Amplifier Box User Manual

INTRODUCTION

General Product Description

The “BM240” is an amplifier box for built-in power supply ,It Can play optical source , bluetooth source and Aux source music. It includes a left and a right channel for stereo.There is a pair button and an indication of RGB lights.and a dial switch for selecting a different EQ .

Definitions, Acronyms, Symbols and Abbreviations

Abbreviation

| Comment| Abbreviation|

Comment

---|---|---|---
CRS| Customer requirements Specifications| dB| Decibel: Unit of Sound Level
EMC| Electro Magnetic Compatibility| Hz| Hertz: Unit of Frequency
LED| Light Emitting Diode| BSMI| Bureau of Standards, Metrology and Inspection
N/A| Not Applicable| SASO| Saudi Arabian Standards Organization
Oct| octave| NOM| Norma’s Officials Mexicans
TA| Type Approval| PC| Polycarbonate
TBC| To be confirmed| ABS| Acrylonitrile Butadiene Styrene
TBD| To be defined| POM| Polyoxymethylene
ID| Industrial Design| CE| Conformité Européenne
DV or DVT| Design Verification Test| FCC| Federal Communications Commission
DM or DMT| Design Maturity Test| ODM| Original Design Manufacturer
FM| Frequency Modulation| PSS&L| Product Safety, Security & Liability
RMS| Root Mean Square| 50N| 50 Newton
PHC| Power Handling Capacity| TR| Trial Run
RH| Relative Humidity| TCMF| Test Case Management File
ESD| Electro Static Discharge| PMPO| Peak Music Power Output
S/N| Signal to Noise Ratio| IEC| Intern. Electro technical Commission
THD| Total Harmonic Distortion| Fo| Resonance Frequency
EUT| Equipment Under Test| TPU| Thermo Plastic Urethane
SoC| Statement of Conformance| SPL| Sound Pressure Level
FR| Flame Retardants| HDMI| High-Definition Multimedia Interface
OEM| Original Equipment Manu fact.| HDCP| High-bandwidth Digital Content Protect.
&| Important remark| CEC| Consumer Electronics Control
| | FRS| Functional Requirement Specification

Table 1 Definitions

General Product Overview

Front Panel:

  • AUX input
  • Optical input
  • Service (softwear updata)
  • BT/Pair button
  • 100-240V~50/60Hz,80W (Power in)

Rear Panel:
Rear Panel

  • Dial switch(choose a different EQ)
  • Output terminal( left and right)
Remote

Remote Control

  • Mute
  • Power
  • Volume up
  • Last
  • Pause
  • Next
  • Volume down
  • Aux source
  • Optical sourse
  • BT source
  • When pushing |<< on the remote for 2s BT pairing is turned OFF
  • When pushing >>| on the remote for 2s BT pairing is turned ON
  • When pushing the BT button on remote for 2s the device is disconnected from the phone currently paired with the BM240, this allows a change in who is connected via remote
Key Features and Performance
  1. Bluetooth input source, requires Distance greater than 10m in open distance.
  2. The pair bottom can set the bluetooth .
  3. The RGB LED indicate different states .
  4. Remote control. requires Distance greater than 10m in open distance.
Special connectors & modes.

Debug/Tuning connector
A 6 pin connector will be present on the PCBA to allow the connection to the MCU for Debug and Tuning purpose.

Factory test mode
Set the dial switch as below picture.
Factory test mode

System Structure

Digital-in

Optical input can support a rate of 192Khz . Don’t support Dolby and DTS . only PCM 2.0.

Analog-in

Aux input max 1.25V rms input, standby mode by audio signal detector .

BT-in

ATS2819 moudle, Can support BT5.0 .

Operating Frequency Band 2.4GHz — 2.48GHz unlicensed ISM band
Bluetooth Specification V2.1+EDR /V4.2
Bluetooth Protocol A2DP,AVRCP,HFP,SPP

BAS,DIS,FMP,HRP,HRS,HTP,HTS,IAS.1_,LS
Output Power Class| Class 2
Operating Voltage| Core: 1.2V, I0:3.1 V, BAT:3.3V-4.5V
Operating temperate range| -10°C — +70°C
External Interface| UART,SPI,TW1,12S,IR,SD Card,USB,DMIC

DSP-functionality

The DSP(ADAU1761) – functionality consists of the following features:

  • Volume control
  • EQ
Amplification

The AMP(TPA3116) is class D – type, driving 4 ohms speakers.

User Interface
  1. output terminal (4 ohm loads can be connected and output 2X25W)
  2. AC in (100-240V~50/60Hz,80W )
  3. pair button (the remote control pair and reboot the BT)
  4. indication LED
  5. optical terminal
  6. Dial switch (set different EQ)

Bottom

  • pair bottom : the remote control pair and factroy reset.
  • Press and hold on till blink red: factroy reset.

indication LED

LED 1x RGB LED
Bluetooth mode Blue
Optical ORANGE
AUX GREEN

The buttons’ feature and led features.

Buttons:

Button name Button operation Feature
pair button Short Press Enter the remote control pairing mode
Press hold on till blink red factroy reset

Led

| Behavior|

The meaning

---|---|---
RGB| Solid Red| Standby mode
Solid Green| AUX source
Solid Orange| OPT source
Solid Blue| BT source
Blink Red fast| Factory data reset

Performance specifications

Audio Specifications

Test conditions: BM240 coneccted with 4 ohm load .

Power AMP Section (Test mode)

PARAMETER(aux in) SPECS
Continuous Average Power 4 ohms
THD 4 ohms
S/N 25W
Frequency Response 20Hz – 20 kHz
CHANNEL SEPARATION
Sensitivity
PARAMETER(optical in) SPECS
Continuous Average Power 4 ohms
THD 4 ohms
S/N 25W
Frequency Response 20Hz – 20 kHz
CHANNEL SEPARATION
Sensitivity
PARAMETER(BT in) SPECS
Continuous Average Power 4 ohms
THD 4 ohms

FCC regulatory conformance

This device complies with Part 15 of the FCC Rules. Operation is  Subject to the following two conditions:

  1. This device may not cause harmful interference.
  2. This device must accept any interference received, including interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help

NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

RF Exposure
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

IC regulatory conformance
This device complies with CAN ICES-003 (B)/NMB-003(B).
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals