eco SCAPES 70643 Galaxy Wave Smart Projector User Guide

Galaxy Wavesmart projector
User Guide
**Model # 70643, 70643-1, 70643-DK1

**

Operation

USB-C Power
Plug the USB-C end of the power cable into the product and the USB-A end into the 5V, 2A power source (adapter not included).

Manual Operation

Power Button
Press to turn ON/OFF — will return to last setting used when turned back on.

• Pairing Mode Reset – Press and hold the power button until the dome flashes to enter pairing mode.
• 6hr Timeout – The projected image automatically turns off after 6 hours — lasers and effects will remain on.

Color Wave
Press to change the color of the wave effect. Press and hold to adjust brightness — the dome will flash when the highest/lowest level has been reached. (See Wave Button Guide)
Sleep Sounds
Press to cycle through each sound. Press and hold for volume control — the dome will flash when the highest/lowest level has been reached. (See Sleep Sounds Guide)
Preset Modes
Press to change between 10 preset combinations of effects and sounds. (See Presets in-app)
Wave Rotation Speed
Press to change between pause, slow, medium-slow, medium-fast, and fast. Press and hold to reset to factory settings — the dome will flash when factory settings are reset. App settings will not reset and the device will still stay connected to your phone.
Projected Image and Lasers
Press to cycle through each image combination. Use the scroll wheel on the side of the projector to change the image. Press and hold to adjust the laser’s brightness — the dome will flash when the highest/lowest level has been reached. (See Projection and Laser Button Guide)
IMPORTANT: DO NOT stare or look directly into the LED dome, laser emitter or image projector as this can be hazardous and can damage your eyes.

Projector Placement

• You can use the geometric design of the smart projector to point the light where your want.
• You can set the projector onto the included anti-skid pad. Peel off the pad’s plastic backing and stick it onto the surface were the projector will be set. Make sure the surface is clean and dry.
• The lower the projector is in the room, the larger the projected image will be. Remotely operate your smart Galaxy Wave Projector with the easy-to-use Enbrighten app. Follow the available instructions and resources to set up your smart device.

|
---|---
|

Sleep Sounds Guide

Projected Image and Laser Guide

Color Wave Guide

Thank you for your purchase!

Instructions made easy
Read instructions or watch the easy-to-follow video.
Scan code or visit byjasco.com/70643i

https://byjasco.com/70643i

Register your product
Receive exclusive deals and register your product.
Scan code or visit byjasco.com/deals

https://byjasco.com/register-your-product

Discover more innovative lighting at byjasco.com/lighting

Like our product?
Leave a review on your favorite retailer’s website or amazon.com
Having problems?
Let us know how we can help.
Call 1-800-654-8483 between 7 AM-8 PM, M-F, Central Time.

App Store is a service mark of Apple Inc. Google, Google Play, and Google Home are trademarks of Google LLC. Amazon, Alexa, and all related logos are trademarks of Amazon.com, Inc. or its affiliates.

Patented and patent pending. For more information, visit https://byjasco.com/patents
MADE IN VIETNAM
Distributed by Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114.
This Jasco product comes with a 1-year limited warranty. Visit www.byjasco.com for warranty details.
Questions? Contact our U.S.-based Consumer Care at 1-800-654-8483 between 7 AM–8 PM, M–F, Central Time.
70643 man v1, 07/22

100% recyclable
Separate paper from the plastic before recycling
byjasco.com/recycle paper made from 25% post- consumer waste

FCC STATEMENT

Suppliers Declaration of Conformity I Model #: Model # 70643, 70643-1, 70643-DK1 I Jasco Products Company LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114 I www.byjasco.com
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

1.  this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

SAFETY WARNINGS

DO NOT put your ear next to the speaker as it may cause hearing loss or damage.
Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

• This is NOT a toy and not intended for use by children. Adult supervision is required at all times when children are nearby.
• Indoor use only. Do NOT expose this product to rain, moisture or water under any circumstances.
• UNDER NO CIRCUMSTANCES shall attempt to be made to open the protective housing or operate the device if the product has been damaged.
• Do NOT stare or look directly into the laser aperture as this can be hazardous and can damage your eyes. Intentional long-term viewing of CLASS 2 levels of laser light can be hazardous. As with all bright light sources, when you operate this device in unsupervised general public areas, it is recommended that up-close access to the light be restricted or prevented and the beams are directed into locations where persons are not expected.
• This laser display device incorporates a CLASS 2 laser system which, by itself, may be hazardous. However, this laser display product incorporates a protective housing and diffractive optics in its design so that there is no exposure or human access to laser radiation during operation or maintenance above the CLASS 2 limits. The laser power is within the Class 2 limit of 1mW.
• This product is classified as a Class 2 laser product and complies with the applicable parts of IEC/EN 60825-1 Ed. 2.0:2007 and Ed. 3.0:2014. The manufacturer additionally certifies it complies with the US FDA Federal Laser Product Performance Standard (FLPPS) provided in 21 CFR Subchapter J,104030 and 104031 except for allowable deviations specified in FDA Guidance documents.
• LASERS SHOULD NOT BE POINTED INTO THE SKY WITHIN 10 NAUTICAL MILES (18.5km) OF AN AIRPORT. IF YOU ARE LOCATED WITHIN THIS SPECIFIC PERIMETER, WE RECOMMEND THE LASERS BE POINTED DOWN AT THE GROUND TO PREVENT STRAY BEAMS FROM BEING PROJECTED INTO THE AIR. CHECK WITH YOUR LOCAL AIRPORT OR PROVINCIAL GUIDELINES FOR FURTHER INFORMATION.
• It is the owner/operator’s responsibility to use this device in compliance with local laws.

*RF warning for Mobile device: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the rad iator & your body.

LASER RADIATION DOES NOT STARE INTO BEAM CLASS 2 LASER PRODUCT

WARNING

• THIS PRODUCT IS NOT A TOY
• NOT INTENDED FOR USE BY CHILDREN
• USE INDOORS ONLY
• PLUG ONLY INTO USB SAFETY-CERTIFIED TYPE A PORT
• THE INCLUDED USB CABLE SHOULD ONLY BE USED FOR THIS DEVICE. IT SHOULD NOT BE USED FOR ANY OTHER LIKE ITEMS, EVEN IF THE CABLE CAN BE INSERTED IN THEM.
• LASER LIGHT. DO NOT STARE INTO THE BEAM. CLASS 2 LASER PRODUCT. DIODE LASER-MAX. OUTPUT <1 mW.
  WAVELENGTH 530-534nm.

CAUTION – TABLETOP LASER
Temperature ranges: -20° -40°C (-4°F-104°F)
Max output <1mW / IEC 60825-1:2014
Wavelength: 532nm
Manufacturer: JASCO PRODUCTS COMPANY LLC, 10 E. Memorial Rd., Oklahoma City, OK 73114
Product name: Tabletop laser projector
Beam divergence: 1.5mrad
Rating: 5V 2A max.
Operating humidity: 10%~90%RH
COMPLIES WITH
21 CFR 1040.10 AND 1040.11
EXCEPT FOR DEVIATIONS PURSUANT TO LASER NOTICE NO.50, DATED JUNE 24, 2007.

References

• . Spend less. Smile more.
• Ecoscapes Galaxy Wave Projector manual (70643)
• Product Registration
• LED Lighting
• Recycling Matters at Jasco
• Jasco
• Patents

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>