GLEM GAS GF64GEI Gas and Electric 60cm Built In Ovens Instruction Manual

GLEM GAS GF64GEI Gas and Electric 60cm Built In Ovens

IMPORTANT
This oven is for domestic applications. It is NOT suitable for commercial applications of any kind. Do not install the oven if there is any doubt. Contact Glem Gas Australasia if you require clarification.
This oven must be installed by a qualified and licensed installer in accordance with these instructions. If you do not retain proof of correct installation your warranty will be voided. If your oven is found to be incorrectly installed you will be liable for all service costs. If a warranty call is made and the oven is found to be incorrectly installed you will be charged for the cost of the service even if the oven is not repaired. We will not service an incorrectly installed oven.

Dear Customer,
Thank you for purchasing our product. This manual has been written to assist you and instruct you in the operation of your oven. It will help you get the best performance and make full use of the features of your oven. The safety precaution and warnings are listed for your safety and the safety of others when operating your oven. Please keep this manual in a safe place for future reference.
This oven has been designed for use in cooking of domestic (household) food. Any form of usage other than cooking food is considered dangerous and inappropriate. The manufacture accepts no responsibility in the event problems caused by improper use, incorrect use or faulty installation. A signed installation certificate indicating the installers licence number and details is required for warranty service. OVEN SHOULD NOT BE USED IN A COMMERCIAL ENVIRONMENT This includes semi commercial, commercial or communal applications such as clubs and schools.

NOTE: Model number details are on the inside of the door. Record them here for your records.

Emilia and Glem ovens are manufactured in the Glem Gas factory in Modena, Italy. They have been designed and constructed to meet the following Australian Safety Standards:

• AS/NZ 5263.0: 2017 (Amendment 1)
• AS/NZ 5263.1.1: 2020
• AS/NSZ 1044 – Electromagnetic Compatibility Requirements.

Surface temperatures for all components comply with the standards. Even so certain parts of an oven become very hot during and after use. A cooling fan operates during the cooking cycle and afterwards until the oven cools.

SAFETY HINTS AND USAGE TIPS

1. OVEN DOOR
   Keep children away from the glass oven door while cooking is in progress: if touched, the glass could cause burns. Don’t let children sit on or play with the oven door. Do not use the drop-down door as a stool to reach above cabinets. Do not rest baking dishes or put any weight on the oven door.

2. GRILL – ALL MODELS
   The grill is electric. Grilling must always be done with the oven door closed.

3. USE OF POT HOLDER GLOVES – ALL MODELS
   Make sure that burners and oven trays are cool before touching them unless you are wearing oven gloves.

4. DO NOT MODIFY THIS OVEN
   Do not modify or attempt to modify the technical characteristics of this oven, as this may present a danger to you and those around you.

5. USE THE CORRECT COOKING VESSELS
   For cooking food, use only plates and trays resistant to high temperatures.

6. DO NOT LINE THE OVEN WALLS OR FLOOR WITH FOIL
   Never place aluminium foil directly on the oven racks, floor or wall as the accumulated heat may damage the surface.

7. KEEP YOUR OVEN CLEAN
   To avoid flare ups or fires within your oven we suggest keeping the oven cavity as clean possible. Particularly after roasting something such as a chicken we recommend wiping the oven out thoroughly. Place a tray of water on a lower shelf to assist in reducing fat build ups.

8. PREHEAT FIRST
   Preheating the oven first before starting cooking is advised. On a gas oven there is no indicator light. A gas oven will reach 200C after 10-12 minutes.

GENERAL WARNINGS

• This oven must not be used by persons (including children) whose physical, sensory or mental capacities are reduced or by persons without experience or instruction, unless under supervision of a responsible person or with appropriate instruction on the use of the oven.
• Young children should be supervised to ensure they do not play with the oven.
• WARNING: Accessible parts may become hot during use. To avoid burns young children should be kept away.
• DO NOT USE polyunsaturated oils with cooking in the oven. The type of oil can cause heavy deposits inside the oven.
• DO NOT USE a steam cleaner to clean the oven or use any caustic cleaners to clean the oven.
• DO NOT use harsh abrasive cleaners or sharp metal scrapers to clean the oven door since they can scratch the surface, which may result in shattering of the glass.
• DO NOT spray aerosols near this oven while it’s operating.
• During use the oven becomes hot. Care should be taken to avoid touching heating elements inside the oven. Please keep children away from the oven.
• DO NOT store flammable materials in the oven.
• ALWAYS keep the oven clean to avoid fires
• After having used the oven, ensure that all knobs are in the OFF position.
• This oven is unsuitable for use in marine craft, caravans, or mobile homes.
• DO NOT USE AS A SPACE HEATER
• If the oven fails to operate correctly, call Glem Gas Australasia Pty Ltd or their appointed agent for service. DO NOT ATTEMPT REPAIRS YOURSELF.

Glem Gas Australasia Pty. Ltd. does not accept any responsibility for damage caused by inappropriate, incorrect, and irrational use. For detailed information, refer to the Warranty Card. Contact Glem Gas Australasia Pty. Ltd. on 1 300 307 917 for all service enquiries. On websites www.glemgas.com.au and www.emiliaappliances.com.au you will find details of our latest products and a source of useful and additional information. With a view to continuously improving our products, we reserve the right to make modifications to their technical, functional or aesthetic characteristics in parallel with technological developments.

BEFORE USING FOR THE FIRST TIME
Remove all packing material and literature from the oven before connecting the gas and electricity supplies. Make sure all plastic has been removed before use. Some models have trays with a protective coating; make sure the plastic coating has been removed. Clean the interior of the oven and all accessories with soap and water and dry them carefully. Switch on the empty oven on maximum to eliminate grease residues from manufacturing. There may be a slight odour at this time. Run the oven on maximum for a period of 1 hour and open the kitchen windows to ventilate. If this odour lingers use the oven and the odour will dissipate.

1. The oven is fitted with 4 guides for positioning trays and racks at different heights.
2. The oven comes with 2 RACKS: Used to support containers for cooking food.
3. The oven comes with a grill tray and rack insert:

Removing & Installing the Oven Shelves 

1. The shelves in your oven have been designed with safety stops.
2. Slide the oven shelves towards you until they reach the front stop tilt them up at the front to clear the side supports and lift them clear. To install them reverse the procedure.

GAS OVEN

DESCRIPTION OF CONTROLS
Use the controls and knobs on the oven instrument panel to select the various functions.

‘TIMER’: Minute counter – rotate the knob to the desired time up to 60 minutes and a bell will ring at the end of the time period. For very short time periods turn the knob past the point you want and then back to it to load the timer mechanism. Some models may have an electronic timer. Refer to electronic timer instructions in this book.

• ‘MODE’: Function selector – selects the oven functions.
• Position 0: Light off. The oven functions in Classic Bake mode without the light – low power consumption baking.
• Classic bake: The oven operates without fan assistance, light on.
• Fan Bake: Oven operates with fan assistance. Light on.
• Fan Grill: The electric grill operates with the fan assistance. Leave the door closed while grilling.
• Grill: The electric grill operates without fan assistance. Leave the door closed while grilling. “Grill” indicator light operates when grilling.

GAS OVEN’ :
Selects the temperature most suitable to the specific cooking requirements. The oven is equipped with a gas thermostat. Its purpose is to keep the temperature as a constant heat. The oven is fitted with electronic spark ignition and a safety gas shut off device that shuts of the gas if the flame fails for any reason. Top position 0 switches the oven off.

OVEN OPERATION

Lighting the Gas Oven
The oven burner must be ignited with the DOOR OPEN. There is a safety device which prevents the oven lighting unless the door is in the open position

1. Open the oven door and remove the grill tray and leave it out.
2. Press the ‘GAS OVEN’ knob and rotate it anti-clockwise to the maximum setting. The electronic ignition is activated automatically when the knob is depressed.
3. Keep knob depressed for about 15 seconds after the flame has lit. Always view the flame during the lighting procedure for safety. There is a hole in the base for viewing the burner.
4. Release the knob and select the desired temperature. Wait a minute and close the door gently.

The oven burner is fitted with a safety valve which blocks the gas supply if there is a failure in igniting the burner or if the flame is extinguished.
Manual Lighting of the Oven
In case of ignition malfunction or an electricity failure depress and rotate the ‘GAS OVEN’ control knob in an anti clockwise direction to reach the maximum temperature. Keep the knob depressed while lighting. Light a match and place it into the hole in the base plate. Once the burner has lit keep the knob depressed for 15 seconds. When lighting the oven for the first time – if the electronic ignition fails to light the oven – light the oven manually and run the oven by running it in at 200 degrees for 20 minutes. This will burn in the burner and remove any moisture that may have prevented the oven from lighting electronically.

OVEN PREHEATING
Once the oven is lit set the oven knob to the required temperature and wait for about 20 minutes before introducing the food. Comply with the cooking indication chart in these instructions and to get the best out of the oven choose the right shelf position. On a gas oven there is no temperature indicator light.

ELECTRIC OVEN

DESCRIPTION OF CONTROLS
Electric ovens have the advantage of being able to offer different types of heat to suit many cooking applications. Models vary according to the functions available.

TIMER: Minute counter – rotate the knob to the desired time up to 60 minutes and a bell will ring at the end of the time period. For very short
time periods turn the knob past the point you want and then back to it to load the timer mechanism. Some models may have an electronic timer. Refer to electronic timer instructions in this book.

‘MODE’: Function selector – selects the oven functions. The oven
functions vary for each model.

‘TEMP’: This thermostat pilot light switches on and off during cooking to show that the heating cycles are taking place properly. For Static and fan forced mode, the oven must always be preheated. For optimum results, try to open the oven door as little as possible, opening the door lowers the temperature suddenly and affects the thermostat cycles. When cooking on different shelves simultaneously, put all containers in the centre of the shelves.

‘OVEN’: The oven temperature is controlled by a thermostat. Select the required temperature for the cooking task. The indicator light goes out when the temperature is reached.

OPERATING THE OVEN
Remove the grill tray. Choose a function using the MODE switch. Turn it to the symbol of the cooking function you wish to use. Then rotate the thermostat knob to the desired temperature. Wait until the thermostat indicator light goes out. This indicates that the oven has reached temperature. Then introduce the food to be cooked. Over the page is a description of the functions that may be on your oven.

OVEN FUNCTIONS – Electric Oven (functions vary according to model)

• FAN FORCED : The heat is generated by a circular element and distributed by a fan. Fast and efficient and allows for baking on more than one shelf. Some foods may need to be rotated using this function.
• ELECTRIC GRILL : On some models this is the inner part of the upper element. Always grill with the door closed. Recommended operation is for 30 minutes only, great for toasting, browning foods etc.
• FAN ASSISTED GRILL : A fan operates with the grill ideal for cooking thicker cuts of meat. Great for steaks. Always grill with the door closed.
• DEFROST : Fan operates which shortens defrosting times.
• PREHEAT : A time saving function that quickly preheats the oven to a preset 160C. You can then set your desired cooking function

COOKING TABLE

Cooking Notes:

• The information provided is purely a guideline. Modify to suit experience, eating habits and personal taste.
• The times indicated in the table do not include preheating of the oven, which is always recommended.
• The time and temperature indicated refer to average quantities of food: meats1/1.5kg, dough for confectionery, pizza, bread 0.5/0.8kg.
• Information in brackets about shelves indicates the shelf to be used when cooking several dishes together.
• When cooking on different shelves simultaneously put all containers in the centre of their shelves.

NOTE: All ovens are different and your new oven may perform differently to your previous model.
Shelf positions and operating temperatures may vary to what you are accustomed. It sometimes takes a few uses to become fully familiar with the characteristics of your new oven.

COOLING FAN FEATURE
Our ovens have a cooling fan that continues to run after the end of the cooking cycle. The fan will stop once the residual heat in the oven has dissipated. It assists in keep the outside of your oven cool and prevents damage to surrounding surfaces.

BAKING TROUBLE SHOOTING
All ovens are different and it can take some time to learn the cooking characteristics of your new oven. Listed below are some common problems, causes and suggested solutions that may assist

Heat variations in oven

| Use shelf to place food in centre of oven Try alternatives

Turn food while cooking

Burning on top| Oven not preheated

Aluminium foil in oven

Food too close to top of oven

| Turn oven on and wait for oven to reach temperature before placing food in the oven

Remove foil

Place on a lower shelf

Burning on bottom| Temperature too high Baking tins too large

Baking tins are dark coloured Food too low in the oven Opening the door too

frequently

| Lower the temperature

Use correct sized tins or reduce temperature Use light coloured tins or reduce temperature Raise to a higher shelf position

Do not open the door too often while cooking

Meat and potatoes not

browning

| Poor heat distribution on food| Try to place the food on a rack to allow the heat to

distribute evenly around the food

Cakes have hard split crusts and appear over cooked| Temperature too high Food too high in the oven Cake tin too deep

Cake tin a dark colour

| Lower the temperature Use a lower shelf position Use correct size tin

Use a light coloured tin

Cakes sunk in centre and seem under

cooked

| Temperature too low Cooking time is too short

Door opened too early

| Increase temperature

Increase length of cooking time

Do not open door until late in the cycle

For more ideas and information go to www.glemgas.com.au

GRILL OPERATION – NOTE: Electric grill on all models
The grill is operated by the ‘MODE’ control knob. The oven door must be closed during grill operation. The grill element is an infrared type, which provides an even controlled heat.
Always grill with the oven door closed – the oven and grill cannot be operated at the same time.

NOTE: If the oven thermostat knob is turned accidently during the operation of the electric grill, a safety device will switch off the grill.

GRILLING TIPS:

• Before introducing food inside the oven it is advisable to pre-heat the oven for at least 5 minutes.
• Place the food to be grilled on the appropriate rack or tray, positioning it at the highest level depending on the volume of food and the amount of direct heat you want to apply.
• Place a dripping pan in the bottom compartment of the oven to collect fats.
• Using a standard shelf with a drip tray below filled with some water will avoid smoke build-up coming from burnt fat and at the same time assist in keep the food moist.
• Depending on the type of food cooked (meat, fish, poultry, etc.), it is necessary to turn it over to expose both sides to the heat from the elements.
• The grilling process should not exceed 30 minutes.

USING THE ELECTRONIC TIMER

Setting the Clock
When the oven is first connected, or after a power failure, ‘0.00’ will flash on the display. To set the clock, push the middle set button and the (+) or (–) buttons immediately to the desired time. The time of day will be saved after 10 seconds.

Using the Timer
The timer can be set for a maximum period of 99 minutes and a minimum of 10 seconds. To set the timer just push the (+) or (-) button until you have set the required time in minutes and seconds.

When the timer is operating the timer on indicator will be lit. Once the pre- set time has elapsed, the timer will beep Push the SET button to switch off. The (–) button can also be used to change the volume of the beep.

CLEANING AND MAINTENANCE

WARNING : the oven must be kept clean, as a build-up of fat constitutes a fire risk.

1. Cleaning of Stainless Steel : In order that your oven retains its new appearance, care should be taken to protect the stainless steel finish. Never use gritty or abrasive sponges. We highly recommend stainless steel cleaners and protectors. Stubborn stains can be removed by soaking in hot water and stains can be prevented by using a clean cloth soaked in soapy water before a spillage becomes cold or dries up. Acid materials like milks, vinegar, citrus juice can damage the most resistant surfaces. If a spill occurs wipe it up immediately.
2. Oven Cleaning : Oven spills should be cleaned straight away. Leaving them will cause burning and smoking inside the oven the next time it is used. Leaving spills can also cause permanent damage to the enamel and make it extremely hard to remove later. A non-caustic cleaner should be used such as non-caustic “Mr. Muscle” to clean the chamber of the oven. Don not use caustic cleaners. Do not use abrasive scourers, sponges or cleaning products. Wipe the oven out regularly while the oven is still warm using hot soapy water and a soft cloth. The removal of the side supports makes cleaning easier.
3. Cleaning of Oven Door – All models: The inner door glass is held in by a bracket at the top of the door. This can be removed and the glass slid out to allow cleaning in between the sheets of glass. With the glass removed the tension in the hinges will cause the door to slam closed so be sure to hold the door handle. The glass can be soaked in hot soapy water or special glass cleaners. The outer glass should be cleaned with a specific glass and mirror cleaner. Soapy water may leave streaks.
4. Removal of Side Shelf Supports – All models: The side racks are removed by simply flexing the bottom rail off the support and unhooking at the top. To replace just reverse the procedure.
5. Grill Element/Top Element – All models: This element must never be sprayed with any detergents. A damp cloth and a bottlebrush can be used to clean the roof of the oven and the element itself. Never soak the element and always dry it after cleaning as not doing so can lead to deterioration. It is important to clean this area regularly as fats spit up and stick to the ceiling and element while grilling and they may burn, smoke and give out unpleasant odours.

REPLACEMENT OF INTERNAL OVEN LIGHT

WARNING : Ensure the oven is switched off before replacing the lamp to avoid the possibility of electric shock. Remove the glass protection cover unscrewing it in an anti-clockwise direction, replace the bulb with a similar bulb (15W) and reassemble. Only use oven bulbs (T300°C) 15w. Never touch the bulb directly; use protective gloves. Only use bulbs available from authorised service centres

REMOVING THE DOOR
Open the door fully and flip over the locking tabs. Close the door gently until it stops on the hinge mechanism. Hold the two sides of the door placing your hands near the hinges. Lift the door upwards, forming an angle of about 45% and carefully lift it away from the oven. To reassemble the door, insert the hinges making sure they locate in the groove at the bottom of the hinge. Allow the door to open fully making sure it stays in the grooves. Flip the locking tabs back over and close the door. If the door is out of alignment repeat the process.

TROUBLESHOOTING

Faults
If there is a problem with the oven or grill please check the points listed below before calling for service. You may be able to solve the problem yourself saving the inconvenience of a service call.
Refer to page 12 for cooking problems. Service charges will apply to issues created by incorrect installation, installation by a non certified gas installer or incorrect use of the oven.

Warranty Service – Tel 1 300 307 917
When calling for warranty service you will need to provide evidence of:

1. Date of purchase
2. Certified installation
3. Model number (found on the data plate inside the door)
4. Serial number (found on the data plate inside the door)

Fuse has blown. If continues to

happen call for service.

Controls not set correctly
Oven not reaching temperature| Incorrect temp selected
| Gas burner not lit
Incorrect oven function selected
Oven smells when first used| Manufacturing residues being expelled. Continue cooking and they will dissapate.
Hot air blowing from above the door| This is normal operation of the cooling fan
Fan continues to run| This is normal operation and the fan will stop once oven has cooled

OVEN INSTALLATION INSTRUCTIONS

Qualified and licenced technicians only. WHEN INSTALLING AN OVEN THERE MUST BE A CAVITY SPACE UNDER THE OVEN TO ALLOW AIR FLOW. MOUNT THE OVEN IN THE CAVITY ON 2 X 100mm WIDE SUPPORTS. THERE SHOULD BE 50mm AIR CLEARANCE UNDERNEATH.

The gas oven has a gas connection on the right side rear of the oven 32mm from the edge and 480mm from the base of the oven. The electrical connection is by a 1.4 flex and 10 amp plug.
POSITIONING THE OVEN -all

models
The oven is designed to be built in to a fixture. The dimensions must be per the measurements indicated in Figures 1, 2 and 3. The top/rear parts of the fixture must have an aperture of at least 80-90mm in depth as shown in Figure

1. Screw in the 4 screws, first inserting them into the bushing and then inside the frame (Figure 1 A/B). For installation under a worktop, ensure that the rear/bottom part of the fixture has an aperture as shown in Figure 1. (reference C) Do not use the door as a lever to insert the oven into the fixture. Do not exert excessive pressure on the open door. When installing the oven ensure that the supply cable does not kink. Where the appliance is built into a cabinet, the cabinet must be capable of withstanding 70°C. Installation into low-temperature tolerant cabinetry (e.g. Vinyl coated) may result in deterioration of the low-temperature coating by discoloring or bubbling. If the appliance is to be installed adjacent to vinyl-wrapped surfaces, use an installation kit available from the vinyl-wrap supplier. Glem Gas does not accept responsibility for damage caused by installation into low-temperature tolerant cabinets. After installation, test and ensure that the appliance operates correctly before handing it over to the customer. A duplicate data plate is supplied. Attach that do an adjoining surface for reference.

LOCATION OF INSTALLATION

The oven must be installed and operated in a suitable place and in conformity with the laws in force.

Air flow requirement
The installer must refer to the laws in force regarding ventilation and discharge of combustion products. The place where the gas oven is installed must have a natural air flow necessary for gas combustion. The room air flow required for combustion on Emilia and Glem gas ovens is 5 cubic meters/hour.

Discharge of combustion products
The gas cooking ovens must discharge combustion products through extractor hoods connected directly to a flue or directly to the exterior as shown in the figure below. If it is not possible to install an extractor hood, an electric fan must be installed to an external wall or window of the room.

Components illustrated in the figure:

• A: Air inlet opening
• C: Extraction hood for discharge of combustion products
• E: Electric ventilator for discharge of combustion products

INSTALLATION – ELECTRICAL CONNECTION

This installation must be undertaken by a licensed and authorized technician.

• The electrical supply for the oven must be a 240 Volt 50 Hz.
• The fuse and electrical wiring of the dwelling must support the load of the oven.
• The oven must be earthed. Connect the oven to a properly earthed and rated power socket, as appropriate.
• The flexible cord of the oven must not be subject to direct heat and must be positioned after installation so that its temperature does not exceed 75°C.

IMPORTANT: If a power socket needs to be installed or relocated, the work must be done by a licensed electrician. After installation, perform a brief test of the oven following the instructions in this manual. If the oven does not function, disconnect it from the electricity supply and contact your nearest technical service centre.

The oven is powered by a cable:

• yellow – green= earth
• blue = neutral
• brown = phase

The manufacturer does not accept any responsibility for damages to persons or objects caused by a failure to observe the above prescriptions or due to tampering with even one single part of the device or the use of non-original spare parts.

WIRING DIAGRAM
A label showing the wiring diagram is fixed to the rear of the oven

WARNING!
THIS OVEN MUST BE INSTALLED BY AN AUTHORISED PERSON – PROOF IS REQUIRED FOR WARRANTY SERVICE CLAIMS. The oven has been manufactured with a Natural Gas injector fitted. For use with LPG the oven must be converted by an authorised technician. The warranty will be voided if the LPG conversion is not undertaken by a qualified gas fitter. The conversion kit is supplied. Information on converting the oven is included with these instructions. The requirements of the local gas and electrical authorities must be adhered to, consult AS/NZS 5601 as appropriate. Gas inlet fitting is 1/2” BSP (male) thread. This oven can be connected using an approved flexible hose as specified in AS/NZS 5601 Clause 5.9. This oven is approved for hose connection in compliance with AS/NZS 5601, clause 6.10.1.12. The flexible hose must comply with AS/NZS 1869 (AGA Approved), 10mm ID, class B or D, between 1–1.2m long and in accordance with AS/NZS 5601 for a high-level connection. The hose should not be subjected to abrasion, kinking or permanent deformation and should be able to be inspected along its entire length. Unions compatible with the hose fittings must be used and all connections tested for gas leaks. THE HOSE MUST NOT BE EXPOSED TO TEMPERATURES EXCEEDING THAT FOR WHICH IT IS CERTIFIED. If the connection is for natural gas the test point pressure should be adjusted to 1.00 kPa with the oven operating at maximum. If installing for use with LPG ensure that an AGA-approved gas regulator suitable for a supply pressure of 2.75 kPa is part of the tank supply and the test point pressure is adjusted to 2.75 kPa. There is a gas pressure test point supplied with the oven that must be installed with the inlet hose. It is recommended that an isolating valve and union be fitted, to enable simple disconnection for servicing. These are to be in an accessible location

• Check connections are gas tight with soapy water or other approved method.
• Under no circumstances use a naked flame in checking for leaks.
• Check Gas Adjustments (refer installation – gas checks andadjustments).
• When satisfied that the oven is operating correctly, instruct thecustomer in its safe operation.
• Ensure the customer understands fully by having them operatethe oven in all its functions

GAS CHECKS AND ADJUSTMENTS – LOW FLAME SETTING
Check the low flame setting for the oven burner with the control engaged in the minimum position. Light the oven burner and operate at maximum for 15 minutes. Turn the control until it engages in the minimum position and remove the control knob. Insert a screwdriver in the adjusting screw (located to the side of the gascock shaft). To increase the flame, turn the adjusting screw anticlockwise. To decrease the flame, turn the adjusting screw clockwise. Adjust for a minimum, stable and clear flame. Ensure the minimum flame will not be extinguished when the oven door is closed.

FINAL CHECK
Operate the oven burner on high and low flames and check that the burner ignites properly and has a stable flame. The following may be abnormal

• If the burner has yellow tipping.
• If the burner is extinguished by opening and closing the oven door.
• If the burner fails to ignite properly.
• If the burner fails to remain alight.
• If the electrode constantly clicks when the burner is alight.

When satisfied with the operation of the oven, please explain to the userthe correct method of operation. If the oven fails to operate correctly,contact your local service agent.

Gas checks and adjustments – igniter operation
Check that the igniter successfully ignites the gas and that the burner remains alight. If an igniter fails to work or the burner fails to remain alight, first remove the plug from the electrical power outlet, and then check that all the electrical connections are in place. If the oven fails to operate correctly, call Glem Gas Australasia Pty Ltd or their appointed agent for service. Do not attempt repairs yourself.

Gas checks and adjustments – pressure adjustment
First shut off the gas to the oven. Remove the sealing screw from the regulator test point at the rear of the oven and attach the hose from the manometer to the point. Turn the gas back on and light the burner on the maximum temperature setting. Check the pressure and adjust at the regulator if necessary to reach the settings in the table or on the data plate. For LPG adjust at the regulator at the cylinder. Turn regulator adjusting screw clockwise to increase pressure and anti-clockwise to reduce pressure. Refit the test point sealing screw when finished.

Gas Conversion
If the oven is to be used with another gas type, either Propane Gas or Natural Gas, it must be converted by an Authorised Person. The table in this manual shows the appropriate injector sizes for either Propane Gas or Natural Gas.

IMPORTANT NOTES
THE INSTALLATION IS THE RESPONSIBILITY OF THE PURCHASER AND ANY INTERVENTIONS REQUESTED FROM THE MANUFACTURER DUE TO INCORRECT INSTALLATION ARE NOT COVERED BY THE WARRANTY. Upon completion of the installation, the qualified technician MUST ISSUE A DECLARATION OF CONFORMITY OF THE WORK PERFORMED. The above- mentioned technician is responsible for any damage to persons or objects caused by connections which do not conform to regulations

1. The oven must not be lifted using the door handle.
2. The oven must be serviced and checked every 3 to 4 years depending on usage and condition.

TECHNICAL DATA

| _ _NATURAL| _ _PROPANE
---|---|---
Inj Diam| MJ/H| Gas Press| Inj Diam| MJ/H| Gas Press
Oven Burner| 1.23| 7.5| 1.0| 0.79| 8.5| 2.75

CONVERSION TO ULPG
The gas oven has been configured to operate on natural gas only. To operate on ULPG the oven must be converted. The conversion kit is provided with your oven. This is a relatively simple task but must be undertaken by a licensed gas fitter. No responsibility will be accepted by Glem Gas if this requirement is not met and it will void the warranty To Convert to ULPG Operation

Disconnect the electricity and gas.

1. Remove all oven shelves and grill tray.
2. Remove the cover plate in the base of the oven.
3. Undo the burner mounting screw. There is one mounting screw at the front of the burner.
4. Move the burner assembly slightly forward and to the side to expose the injector. Be very careful not to damage the thermocouple or ignitor lead.
5. Using a 7mm socket remove the injector.
6. Using the same socket, screw in the supplied injector, after first checking the size against the data plate. If there is any doubt please contact Glem Gas service on 02 9721 2755.
7. Carefully reassemble the oven burner.
8. Switch on the oven and check the size of the flame. It should be a steady blue flame that is not too big to protrude beyond the burner plate. Run the oven for a period of time at 180C until it reaches temperature. This is to check that once the oven reaches temperature the flame remains alight when it reduces.
9. Adjust as required. (see below)
10. Reinstall the cover plate.
11. Reinstall the oven shelves and grill tray.
12. Change the gas specification on the data plate and affix the ULPG label to the rear of the oven exterior.

ADJUSTMENT OF THE THERMOSTAT MINIMUM SETTING
The operation is performed with the oven installed in the fixture and after qualified personnel has completed the electrical and gas connections. This measure is necessary whenever the type of gas is changed natural gas to ULPG to guarantee a minimum temperature close to 150°C.

Follow the procedures below:

• Open the oven door
• Remove the floorplate
• Turn on the oven at maximum temperature and light the burner.
• When ignition has taken place, close the door.
• Position the knob of the thermostat at a temperature of approx. 150°C.
• Remove knob “a”.
• Insert a screwdriver in hole “b”, parallel to the stem of the thermostat and adjust the by-pass until a reduced but stable flame is obtained. This operation must be carried out with the oven door closed.
• Use a slotted screwdriver on the by-pass screw.
• When using ULPG, the by-pass adjustment screw must be fully tightened.

After having adjusted the burner, check that the flame remains at a minimum by following the procedures below:

• Turn the knob from the minimum to the maximum position 3 times.
• Open and close the oven door continuously 4/5 times, neither too quickly nor too slowly.
• If the flame goes out, adjust the by-pass once again (by slightly increasing the minimum setting).

Once these operations have been completed (injectors replaced, air and minimum setting adjusted), turn the oven off and up-date details on the label present on the oven door frame, indicating the new gas used.

PRODUCT WARRANTY

Thank you for choosing a Glem Gas Appliance, the purchase of this appliance is an important investment in your home and so to protect your investment we urge you to complete the registration card attached, please return it immediately. IT IS A WARRANTY REQUIREMENT THAT PROOF OF PURCHASE BE PROVIDED PRIOR TO REQUESTING A SERVICE CALL. THIS WARRANTY SHALL NOT APPLY IF THE APPLIANCE WAS NOT INSTALLED BY A LICENSED TECHNICIAN AND PROOF IS NOT SUPPLIED. The benefits conferred by this warranty are in addition to all other conditions and warranties in respect of this product which the consumer may have under the Trade Practices Act 1874 of the Commonwealth of Australia and/or similar State or Territory Laws. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality
and the failure does not amount to a major failure.
Glem Gas Australasia Pty Ltd warrants, this appliance to be free from defects in workmanship and materials for a period of:

1. Where the appliance is intended to be used and is used for DOMESTIC USE – 24 MONTHS FROM DATE OF DELIVERY TO THE ORIGINAL PURCHASER.
2. Where the appliance is intended to be used and is used for COMMERCIAL USE – 90 DAYS FROM DATE OF DELIVERY TO THE ORIGINAL PURCHASER.

Glem Gas Australasia Pty Ltd, during the period of warranty, will at its option, and subject to the terms and conditions stated below, repair or replace free of charge this appliance or any component part, which upon examination by Glem Gas Australasia Pty Ltd is found to be defective.

THIS WARRANTY SHALL NOT APPLY:

1. If the rating plate has been removed or the serial number or other details on it have been removed or rendered illegible.
2. If the appliance is connected to any gas type or voltage other than shown on rating plate.
3. If the appliance has been subjected to misuse, abuse accident or want of care.
4. If the appliance has been installed, operated or maintained contrary to the instructions supplied by Glem Gas Australasia Pty Ltd.
5. If any defect or failure is due to connection to an inadequate or faulty gas or power supply.
6. If damage is caused by foreign objects in or on the appliance or because of its use for purposes other than that for which it was delivered.
7. If a repair has been made or attempted by the purchaser.
8. Where the oven is installed outside an 80km radius from the GPO of any Australian Capital City to freight and travel costs beyond that radius.

This warranty does not cover any glass damage or replacement of light bulbs. Parts covered under warranty that need replacing i.e.: seals, knobs and burner caps. These can be posted to customer to put on at their discretion. This Warranty is given by Glem Gas Australasia Pty Ltd and no other person or organisation is authorised to vary its provisions and conditions

INSTALLERS CHECKLIST
You must test the oven after installation before you hand it over to the customer. On gas ovens, you must have a manometer and a connecting tube to check that the gas pressure is correct.
The following checks must be made to commission the oven and to activate the warranty. If this form is not completed fully and correctly it will void the warranty.

GLEM GAS AUSTRALASIA PTY. LTD. P.O. Box 63 Blaxcell PO South Granville NSW 2142 Phone: 02 96433500 – Fax: 02 9643 3599 – www.glemgas.com.au Email us info@glemgas.com.au Free call 1 300 307 917

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>