LYQiLY L766 Wireless Mouse User Manual
- June 4, 2024
- LYQiLY
Table of Contents
LYQiLY L766 Wireless Mouse
Reconnection
Both of mouse and Nano receiver has a built-in code, it can be setting one mouse to one receiver, or few of mouse to one receiver. Mouse and receiver need to reconnect under the condition of High temperature, high magnetic, strong vibrate.
- Plug off Nano receiver from USB port, and plug it on
- Keep the mouse in 50CM with receiver, re-store the battery
- You can use it by reconnection
Note
If there are large obstacles between the mouse and the receiver, the
transmission distance will be reduced.
The uneven or reflective desktop may affect the use of the mouse.
Package Content
- 1x wireless mouse
- 1x Nano receiver
- 1x manual
Product Feature
- 2.4G working frequency, extensive applicability, transmission distance can reach to 10 meters.
- Using USB high-speed transmission technology. The transmission speed is two times faster than the normal mouse. The polling rate can reach to 250Hz and can be switched to 125Hz. No delay can better meet the requirements of gamers.
- Using the most advanced high-end power-saving chip PAW3212, lower power consumption, more stable cursors and stronger adaptive surface ability.
- Using infrared LED as mobile tracking source.
- Five kinds of adjustable CPI level: 800/1200/1600/2000/2400CPI, with CPI gear indication. The default is 1200CPI.
- Multilevel power-saving mode, saving the battery energy as far as possible.
- Super micro (Nano) receiver, plug and play.
Installation
- Find the wireless mouse and Nano receiver in package
- Plug Nano receiver to USB port on PC
- 1 PCS AA battery into Mouse body Properly
- LED indicator will keep flash for few seconds, the Mouse is ready to work.
Advanced function
-
CPI adjustable functionWith 5 adjustable CPI 800/1200/1600/2000/2400, the default is 1200CPI. Press the switch button on top of Mouse can easy to adjust CPI. LED indicator will flash once while it converting to 800CPI, LED indicator will flash twice while it converting to 1200CPI, LED indicator will flash three times while it converting to 1600CPI, LED indicator will flash four times while it converting to 2000CPI, LED indicator will flash five times while it converting to 2400CPI.
-
Polling rate adjustable function 2 adjustable polling rate 125Hz/250Hz, the default is 125Hz. Press and hold the right button and scroll wheel button to converting, the LED flash 5 times in low speed for 125Hz converting, the LED flash 5 times in fast speed for 250Hz converting.
-
The unique side keys have forward and backward functions.
-
Saving power mode and power switch off If the mouse stays out of work for 8 minutes, it will turn to power saving mode, press any button to restart it.
If you turn off the PC or take out the Nano receiver from USB port, press any button or move the mouse to enter the power saving mode. Tips: if you don’t use the mouse for a long time, please remove the battery to avoid corrosion. -
Nano receiver
A very small size design for Nano receiver, it can be plugged and stay on a USB port of PC/Notebook without interference.
Portable design for travel, the Nano receiver can be plugged in the slot on the bottom of the mouse.
FCC Warning
-
This device should be installed and operated with minimum distance 5mm between the radiator&your body.
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
-
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.