NiZONi Touch Control LED Dome Lamp with Wireless Phone Charger and HD Audio Speaker Instruction Manual

NiZONi Touch Control LED Dome Lamp with Wireless Phone Charger and HD

Audio Speaker

FUNCTION KEYS

1. Type-C input port
2. Vol + / Next track
3. Speaker ON/OFF
4. Vol – / Previous track
5. Power LED indicator
6. Wireless charging LED
7. Wireless charging PAD
8. LED Lamp / Handle
9. Microphone

WHAT’S INCLUDED

• 1 x Bluetooth Speaker
• 1 x USB to Type-C charging cable
• 1 x Instruction manual

SPECIFICATIONS

• Material : ABS+ Silicone
• Bluetooth version : 5.0
• Speaker output power : 3W
• Night light power : 1.SW
• Wireless output: 1 SW
• Brightness level : 3 levels
• Type C Input : 5V/3A, 9V/2.5A
• Distortion rate : 10%
• SNR: 70dB
• Frequency: 20Hz-20KHz

INSTRUCTIONS

(BE SURE DEVICE IS ALWAYS CONNECTED TO A POWER SOURCE USING THE CABLE PROVIDED

CHARGING THE SPEAKER

Connect the provided charging cable to a power source and to theType-C port (1) on the speaker. Once connected that Power LED lndicator(S) will grow GREEN.

BLUETOOTH SETUP

Press and hold Speaker ON/OFF Button(3) to turn ON the speaker. Turn on the Bluetooth function on mobile device, Select “INV00786” pairing name. Speaker will automatically pair if the mobile device has been paired before. Press and hold Speaker ON/OFF Button(3)
to turn off the device.

USING THE SPEAKER

When receiving a phone call, press ON/OFF button to answer and again to hang up. Double press to redial the last call.

• “Vol + / Next track” (2):
  • Long press – next track.
  • Short press – increase volume.
• “Vol – / Previous track” (4):
  • Long press – previous track.
  • Short press – decrease volume.

WIRELESS CHARGING

Place wireless charging enable device on Wireless Charging Pad(6). The device will begin to charge, LED indicator(?) will glow RED when charging.
NOTE: IF THE LED INDICATOR IS FLASHING RED, AN UNKNOWN OBJECT IS BEING DETECTED BETWEEN THE WIRELESS CHARGING PAD AND THE PHONE BY FOD (FOREIGN OB」ECT DETECTION). (THE DEVICE WILL NOT BEGIN TO CHARGE UNTIL OBJECT IS REMOVED.)

NIGHT LAMP

When connected to a power source, tap the handle to turn the lamp on (warm tones). The brightness of the night lamp is controlled by 3 settings. When the lamp is off, the brightness will be increased by 1 setting with each tap of the handle. The lamp will turn off when the handle is tapped a fourth time

SAFETY PRECAUTIONS

Read all the instructions before using the product.

1. To reduce the risk of injury, close supervision is necessary when the product is used near children.
2. Do not expose the device to any moisture.
3. Do not use the device in excess of its output rating. Overloaded outputs above rating may result in a risk of fire or injury.
4. Do not use the device if damaged or modified. Damaged or modified device may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
5.  Do not disassemble the device. Take it to a qualified service person when service or repair is required. Incorrect reassembly may result in a risk of fire or injury.
6. Do not expose the device to fire or excessive temperature. Exposure to extreme heat may cause explosion.
7. Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
8. This device is not a toy.
9. Do not overcharge Phone. Unit may get hot with excessive use. Remove Phone when it is fully charged. Never charge for more than 7 hours at a time.

SAFETY PRECAUTIONS

Attachments on the back of your phone can impede the effectiveness of the wireless charger, and lead to overheating. Please remove attachments from the phone before charging on this device.

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the followingwo condiions
This device may not cause harmful interference.
(2)This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a class B digital device.pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation
This equipment generates uses and can radiate radio frequence energy and,it not nstalled and used in accordance with the instructions,may cause harmful interterence to radio communications.However, there is no guarantee that interterence will not occur ina particular installation.if this equipmemt, does cause harmful intermerence to radio or television reception,which can be determined by turning the equipment oft and on, the user read to tr to correct the interference by one or more of tne Tolownga

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver
• Connect the equipment into an autlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement, This equipment should be installed and operated with a minumum distance of 20 cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>