2BF9J-TGPOR TGpor Air Conduction Bluetooth Headset User Manual
- June 1, 2024
- TGPOR
Table of Contents
2BF9J-TGPOR TGpor Air Conduction Bluetooth Headset
Product Information
Specifications
- Compliance: Part 15 of the FCC Rules
- Interference Conditions: Must not cause harmful interference, must accept any received interference
- Antenna Usage: Must not be co-located or operated with any other antenna or transmitter
- RF Exposure: Meets general RF exposure requirement in portable exposure condition
Product Usage Instructions
Compliance with FCC Rules
Ensure that the device complies with Part 15 of the FCC Rules to avoid any
legal implications. Do not make changes or modifications to the unit without
express approval.
Interference Handling
Be aware that the device must not cause harmful interference and must
accept any interference received, even if it leads to undesired operation.
Follow proper handling procedures in case of interference.
Antenna Usage
Do not co-locate the device and its antenna(s) with any other antenna or
transmitter to prevent signal conflicts or disruptions in operation
RF Exposure Compliance
The device has been evaluated to meet general RF exposure requirements in
portable exposure conditions. Use the device within these specified conditions
to ensure compliance.
Frequently Asked Questions (FAQ)
-
What should I do if the device is causing interference?
If the device is causing interference, try repositioning it or adjusting its settings. If the issue persists, contact customer support for further assistance. -
Can I modify the device without approval?
No, modifications to the device must be approved by the responsible party for compliance to avoid voiding the user’s authority to operate the equipment.
User Manual
Please read the instruction carefully before use
Headphone Controls
ON/OFF
Turn on the headphones
Press and hold the”+’ Button until the LED Indicator flashes blue. ‘the
headphones will say: “power on”
Turn off the headphones
Press and hold the”+” Button until the LED Indicator flashes blue. the
headphones will say: “Power off”
Pairing
- Start with the headphone turned off.
- Press and hold the”+” Button for 1 to 3 seconds until the LED Indicator flashes red and blue alternately.
- Open your (mobile phone/ computer) device’s Bluetooth settings and select “K3 Pro”, Click the device to pair and connect.
How to Wear
Pick up the headphones, bring them behind the back of the base of your neck, position the earhooks on your ears, then enjoy your music!
wearing your headphones the wrong way could cause discomfort.
The transducers should rest in front of your ears.
Volume
How to change volume
While your audio is playing, adjust headphone volume by pushing either the
Volume + or Volume – buttons.
A “beep” will sound when the volume is at its max.
Listening with headphones at high volume may affecty our hearing and the
audio will be distorted.
Operating Instruction
Charging Tips
The first use of the headset must be fully charged to the battery. In use, if
only the red light flashes and the voice prompting low power, that the battery
is low, then you need to charge the headset. The charging cable should be
connected to the headset’s magnetic charging port, about 2 hours to fill.
Charging status indicator flashing breathing light, full charge often blue
light.
Note: Magnetic charging has a positive and negative pole corresponds to
each other adsorption can be charged normally, mustual repulsion can not be
charged or even cause a short circuit.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.
Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirement in
portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>