Callista BM9020 LED Mirror Light Range Instruction Manual
- June 1, 2024
- Callista
Table of Contents
Callista BM9020 LED Mirror Light Range
Specifications
- Model: BM9020, BM9060, BM6060, BM4214
- Installation: Hanging Bar Method, Hardy Holes Method
- Power Source: Electric
- Manufacturer: Eurotech Lighting
Product Information
The Callista LED Mirror Light Range includes models BM9020, BM9060, BM6060, and BM4214. Please refer to our website for detailed visual representations of each model.
- Ensure the power is turned off.
- Level the hanging by marking with a pencil in the hanging bar hole.
- Use a drill to make the holes.
- Put the extension plug into the wall hole so both the wall holes and the hanging bar holes match. Securely screw the hanging bar to the wall.
- Connect the wiring as per the provided instructions.
- Hang up the mirror and ensure it is secure.
- Turn the power on and carry out the required testing.
FAQ
- Q: Can I replace the LED light source myself?
- A: No, the light source should only be replaced by the manufacturer, their service agent, or a qualified person.
- Q: Can I install the LED mirror light without a licensed electrician?
- A: No, the LED luminaire must be installed by a licensed electrician following all local regulations for safety reasons.
All installations must be carried out by a qualified electrician following
local regulations. Make sure that the power is switched off before
installation.
Please read and follow the ‘Installation instructions’ and ‘Safety
instructions’ sections carefully before commencing installation.
Installation of this model can change from time to time please read
instructions every time before installation. For detailed specifications,
please go to our website
eurotechlighting.co.nz.
Callista – LED Mirror Light Range
Model: BM9020, BM9060, BM6060, BM4214 Installation Instructions
Product Information
POWER
ON/OFF
Installation Instructions
Installation Instructions | Hanging Bar Method
- Make sure the power is turned off
- Level the hanging by marking with a pencil in the hanging bar hole.
- Use a drill to make the holes
- Put the extension plug into the wall hole so both the wall holes and the hanging bar holes match. Securely screw the hanging bar to the wall.
- Connect the wiring as per the below instructions.
- Hang up the mirror. Check it is secure.
- Turn the power on & carry out the required testing.
Safety Instructions
Read these instructions carefully before commencing installation
- The light source contained in this luminaire shall only be replaced by the manufacturer this service agent or a similar qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, or explosive.
Callista – LED Mirror Light Range
Model: BM9020, BM9060, BM6060, BM4214
All installations must be carried out by a qualified electrician following
local regulations. Make sure that the power is switched off before
installation.
Please read and follow the ‘Installation instructions’ and ‘Safety
instructions’ sections carefully before commencing installation.
Installation of this model can change from time to time please read
instructions every time before installation. For detailed specifications,
please go to our website
eurotechlighting.co.nz.
Product Information
ON/OFF
Installation Instructions – Hardy Holes Method
- Make sure the power is turned off
- Choose portrait or landscape installation first. Use a measuring tape to measure the distance between the two holes.
- Using a level, mark the distance between the two holes. Use a drill to make the holes
- Put the extension plug into the wall hole so both the wall holes and the hanging bar holes match. Securely screw the hanging bar to the wall.
- Connect the wiring as per the below instructions.
- Hang up the mirror, and check it is secure.
- Turn the power on & carry out the required testing.
Safety Instructions
Read these instructions carefully before commencing installation.
- The light source contained in this luminaire shall only be replaced by the manufacturer this service agent or a similar qualified person.
- This LED luminaire must be installed by a licensed electrician ONLY following all local regulations.
- Ensure that the cables will not be squeezed or damaged by sharp edges.
- Clean the light with a soft cloth and a standard PH-neutral detergent.
- Misuse of/or changes to the appliance shall void all warranties.
- Do not install on a surface that is not suitable or deformed.
- Do not install on or above a surface with a high temperature.
- There should not be any materials that are corrosive, or explosive.
For detailed specifications, please go to our website eurotechlighting.co.nz.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>