VIGRUE QIXIJ0165-658 Gas Pressure Washer Surface Cleaner User Manual

June 13, 2024
VIGRUE

VIGRUE QIXIJ0165-658 Gas Pressure Washer Surface Cleaner User Manual
VIGRUE QIXIJ0165-658 Gas Pressure Washer Surface
Cleaner

Pressure Washer Surface Cleaner

  1. 16.5-inch Surface Cleaner has dual pressure water jets that spin rapidly breaking up dirt and grime without streaking or striping surfaces. And it cleans large surfaces up to 6x faster than a standard nozzle.
  2. With pressure washer up to 4,000-PSI,the surface cleaner is ideal for the cleaning floor made of different materials, such as plastic, concrete, tiles, natural stone.
  3. The high-pressure water jets is contained inside of the dome enclosure, no overspray or back splash.

Surface cleaner nozzle maintenance

  1. Remove the nozzle with appropriate wrench (11 mm)

  2. Rinse mounting holes with fresh water to clean impurity

  3. Cover new nozzles thread with attached Teflon tape

  4. Align the nozzle opening reinstall nozzles to the spray bar. Tighten securely.

Please note:

  1. In order to avoid nozzle blocked by sand or other debris, you can use water inline filter.
  2. If the nozzle is difficult to remove please heat it with a hot blower before removing.

Surface Cleaner Top Maintenance

If the pivot connection leaks, please change the o-rings(package included).
Please refer to the following steps:

  1. Remove the screw from the body by using a 5 mm hex wrench.

  2. Replace the original o-ring which is broken with new o-rings.

  3. Reinstall the screw by using a 5 mm hex wrench.

Safety Instruction


WARNING
: To reduce the risk of injury, please read and comply with these
original operating instruction prior to the initial operation and store them for later use or subsequent owners.

  • Please observe the safety instruction of your high pressure cleaner.
  • Fits most pressure washers.
  • Ensure compatibility and proper fit before using this accessory.
  • Spray the pressure stream in a safe direction.
  • Do not point at people, pets, electrical devices or the unit itself.
  • Be aware of the recoil force!
  • Ensure a stable position and firmly hold the high pressure gun with the extension tube or the handle. Always wear eye protection with side shields marked to comply with ANSI Z87.1 Switch off the high pressure cleaner when you finish cleaning.
  • Maximum water temperature 104 F (Please observe the instructions of your high-pressure cleaner) After use or before servicing, always disconnect the surface cleaner from the pressure washer spray wand.

TECHNICAL SPECIFICATIONS

  • Connection: 1/4″ Quick Plug
  • Diameter: 16.5-inch
  • Max Pressure: 4,000 psi
  • Min Pressure: 2,000 psi
  • Max Water Flow: 3.7 GPM
  • Max Water Temperature: 104 7
  • Weight: 8bs

Package Include

2×15″ Pressure Washer Extension Wand 1x 16.5″ Pressure Washer Surface Cleaner 1x Operator’s Manual 20-rings 2 Replacement Nozzles 1x Teflon Tape

Symbol


WARNING:
Don’t hold and the edge of the surface cler.

Description of the Appliance

How to Use the Surface Cleaner See Figure 1

  1. 1 Pull back coloron quick-connect end of wand
  2. Push the surface dimer into place
  3. push the collar forward, insert surface cleaner and release collar Ensure the collar side all tph the way forward. Tigon surface dearer to make sure it is securely in place
  4. Place surface deaner on horizontal surface, push the button to release the tripper lock on any un and pull the trigger operate the machine.

USING THE SURFACE CLEANER See Figure 2

  • Once the surface cleaner is installed connect the hose to the pressure washer as described in your pressure washer manual
  • Start the pressure washer as described in your pressure washer manual.
  • Walk slowly behind the cleaning deck, cleaning as you go

Tips for cleaning

  • Outdoor surface should be swept before the surface cleaner used to avoid damaging the high pressure
  • The surface cleaner is not suited for scouring or scribing. m if striping on swirling occurs, slow your pace.
  • If striping or swing continues, the surface cleaner nozzle(s) may be clogged. Biking any obstacle while using the surface ar wil damage the unit.
  • If contact does occur and i vibration when operating the pressure washer, stop and discontinue. Continuing to operate the could result in serous injury or damage to the unit.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals