Tivoli 147 Litesphere RGBW Adapt Instruction Manual

Tivoli 147 Litesphere RGBW Adapt Instruction Manual

Warnings and Safety

• Please verify the contents of the package!
• Please read instructions before starting the installation.
• Make sure power is off before installing or modifying the system.
• Call Tivoli LLC tech support with any questions.
• This product is designed to work with listed Class 2, 24V DC transformers only. Use of any other power source will cause damage, shorten the life of the fixture, and will void the warranty.
• Consult any local and national codes for installation.
• Follow basic safety precautions when dealing with any luminaire application to reduce the risk of fire, electrical shock, and/or personal injuries. This lighting system should be installed by a certified professional.
• Do not use this product for other than its intended use.
• Do not install this lighting system where the exposed bare contacts can be shorted or contact any conductive material to reduce the risk of fire and burns.
• Do not use any luminaire if damaged, such as a broken globe, loose connections, or frayed wire insulation. Inspect periodically.
• Do not secure any luminaire with staples, nails or like means that might damage the wire insulation.
• Do not cover lamps with cloth, paper or any material that is not part of the product.

Installation

There are 2 mounting options: Surface Mount and Suspension Mount. Step 1 will cover the Surface Mount Option.

1. For the surface mounting option, remove the socket cap and cover and screw each socket to mounting surface using the appropriate screws.
   
   Steps 2-6 will cover the Suspension Mount Option.

2. Attach eyebolts or other mounting hardware to the structural supports that will hold the catenary cable.
   a. The catenary cable is rated for hanging loads up to 200 lbs. and 800 lbs. of pulling tension.

3. Insert suspension cable into the cable following the direction of the arrow on the cable lock.

4. Look the suspension cable through the mounted eye bolt or other mounting hardware and insert the cable back through the cable lock.
   

5. You can tighten the suspension cable using a catenary tensioning tool or loosen the cable using a cable release key on the cable lock.
   Catenary Tensioning Tool
   
   

6. Attach the strands with the sockets to the suspension cable using zip ties.
   NOTE: For strands with on center spacing of 18 in. or greater, use a zip in between globes to prevent sagging. Skip to Step 8 if no shades will be used.
   

7. Create the shade assembly by placing the shade in between the gasket/globe and nut. Tighten the assembly.

8. Remove the plastic cover from the socket .

9. Attach the globe or the shade assembly to the socket
   
   NOTE: To guarantee a proper fit and prevent potential issues, it is crucial to confirm that the gasket has been properly seated and positioned, and ensure it is not bent.
   

10. At the end of the strand, cut 3 inches or more after the last globe to prepare to install the end cap.
    

11. Loosen the end cap assembly and slide the end cap base on the wire
    

12. Attach the end cap cover onto the end cap base and tighten
    

13. Confirm your power is off. NEVER CONNECT STRANDS OR DATABOXES WHILE POWERED. RISK OF PRODUCT DAMAGE.

14. Connect power/data lead to ADNM-DAT power supply.
    NOTE: Refer to related power supply specification sheets for more information and other possible configurations.
    

15. Turn on power and verify the system is operating properly by verifying the following sequences while  NOT connected to DMX.

    • Green Chase
    • Yellow Chase
    • Blue Chase
    • Magenta Chase
    • Cyan Chase
    • White Chase
    • Red Chase

16. Connect Data to DMX Controller
    NOTE: Refer to the related documents of the selected DMX controller for more information on installation and setup
    

References

• Tivoli – Over 50 Years of Innovation and Linear Lighting Leadership.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>