Hearth Hand JC1620 3 in 1 Bluetooth Turntable User Manual

Hearth Hand JC1620 3 in 1 Bluetooth Turntable User Manual

Overview

Front

Rear

Include: The main unit, AC Adapter, Manual, 45 RPM Adapter, AUX Cord.

Essential Setup

1. Plug the power adapter into the electrical outlet and connect other end to the back of the unit.
2. Place the unit on a flat and level surface. The selected location should be stable and free from vibration.
3. Plug the power adapter into the electrical outlet and connect other end to the back of the unit.
4. Extend the FM antenna.
5. Turn on the unit by rotating the Volume knob clockwise until you hear a ‘click’ sound, and the two LED backlight(Amber) on the dial will light up.
6. To power off the unit, rotate the Volume knob anticlockwise until you hear a ‘click’ sound, and the two LED backlight(Amber) on the dial will turn off.

To Open Turntable Cover

1. Lift the turntable cover all the way up until it stops.
2. Lower the cover slowly until the latch engages. If the latch does not engage, pull the lower bar by hand.
3. The cover will now stay open.

To Close Turntable Cover

1. Lift the cover all the way up until it stops.
2. The latch should disengage and you may now slowly lower the cover. If the latch does not disengage, push out the lower bar by hand.
   CAUTION : Make sure you hold the cover to avoid pinching your fingers as it closes.

Phono Operation

1. Turn on the unit and open the cover.
2. The unit defaults BT mode, and you have to press the PHONO button to switch to the phono mode, the indicator above the button will light red.
3. Detach the stylus protector by pressing both sides and pulling straight in the direction shown.

4. Place a vinyl record on the Turntable by aligning the Turntable Spindle to the record hole.
5. Slide the Speed Selector to 33⅓, 45 , or 78 to match the play speed of the record.
6. Unlock the Hold Down Clip.

7. Move the Tone arm gently to the edge of the record. The turntable will begin to turn.
8. Rotate the Volume Knob to adjust the volume.
9. When playback has finished, slightly lift the tone arm using the Lift Lever and return it to the Tone Arm Rest.

Note:

• The 45 RPM Adapter was packaged with this manual.
• Put the 45 RPM Adapter across the Turntable Spindle if play a 45 RPM record.
• The Speed Indicator will illuminate, indicating different speeds. 33⅓ RPM: Green; 45 RPM: Maya Blue; 78 RPM: Pale Syan.

Bluetooth Operation

1. Turn on the unit.
2. The indicator above the BT button blinks in blue, press and hold the BT button, and the indicator will blink faster indicating the unit is in pairing state.
3. Turn on your external Bluetooth device and pair it with the “Hearth & Hand 04” device.
4. A sound will be heard and the indicator will turn to solid blue.
5. Play music on your external Bluetooth device.
6. To adjust the volume, rotate the Volume Knob or operate your external Bluetooth device.
7. To pause or stop the music, press the BT button on the unit or operate your external Bluetooth device.
8. To disconnect the current Bluetooth, press and hold the BT button.

AUX Operation

1. Turn on the unit.
2. Insert one end of the 3.5mm AUX Cable into the AUX IN Jack on the rear of the unit.

3. Start to play your favorite music on your playing device.

Note: The AUX mode has the highest priority over other modes. When play other modes ensure the AUX Cable have been plugged out from the unit.

Radio Operation

1. Turn on the unit.
2. Press the AM or FM button to enter AM or FM mode, and the indicator above will light red.
3. Extend the FM antenna when you want to listen to FM stations.
4. Rotate the Tuning Knob to search for available stations.
5. Adjust the volume by rotating the Volume Knob.

You can improve the signal receiving strength by:
Extend the FM Antenna to a higher position.
Turn the unit to face different directions.
Move the unit to a different place.
Connect the FM Antenna to your outdoor antenna.

Maintenance

• Handle with care, as the stylus is delicate. Use of a bent or broken stylus may damage the record and cause the turntable to malfunction.
• Do not expose the stylus to extreme heat.
• Contact a qualified repair company, if you experience difficulty in changing the stylus.

Removing an Old Stylus

1. Insert a flathead screwdriver at the tip of the stylus and push down to the direction “A” as shown below.
2. Pull the stylus out toward direction “B” as shown below.

Installing a New Stylus

1. Hold the tip of the stylus and insert the other edge by pressing toward direction “C” as shown below.
2. Push the stylus up toward direction “D” as shown below, until it locks at the tip.

Troubleshooting

Specifications:

• Build-in bluetooth function can stream music from hundreds bluetooth enabled devices
• AM/FM high sensitivity receivers ( FM stereo)
• 3-speed Turntable record player (33⅓; 45; 78 RPM) with auto stop
• 3.5mm aux-in jack function with cable
• Pig tail FM antenna
• LED backlight(Amber)
• Bluetooth version: 5.3
• Output power: 2x3W
• Input: 100-240V~ , 50/60Hz 0.5A

Need some help?
Can’t get it to pair? Not accepting phone calls? Just have a question?
Call us at: 1-833-TGT-Tech

Safety

• Do not use near any water source
• Do not modify or repair this device
• Do not use in high temperatures or extreme weather
• Do not use chemical detergents to clean your device, use a soft dry cloth

FCC Exposure Statement
To maintain compliance with the FCC’s RF exposure guidelines, place the product at least 20 cm from nearby persons.

FCC ID: OKUJC1620 Model : NASA Made in China
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Target Corp.Mpls.MN,55403 Phone:1-833-TGT-Tech

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>