Schneider Electric LVS08202D Floor Standing Enclosure Instructions

Schneider Electric LVS08202D Floor Standing Enclosure

Product Specifications

• Model: SeT G IP30
• Model: SeT Pack 250
• Certification: CEI61439 1 and 2
• Manufacturer: Schneider Electric

Product Usage Instructions

Assembly Instructions
The assembly of PrismaSeT switchboards should be done in compliance with certification CEI61439 1 and 2. Only qualified personnel should install, operate, service, and maintain the electrical equipment. Failure to follow the assembly instructions is the responsibility of the installer.

Responsibility Disclaimer
Schneider Electric does not assume any responsibility for consequences arising from the use of this material in case of failure to comply with the assembly instructions.

Frequently Asked Questions (FAQ)

• What certification does the product have?
  The product is certified under CEI61439 1 and 2 standards.

• Who should handle the installation and maintenance of the electrical equipment?
  Only qualified personnel should install, operate, service, and maintain the electrical equipment.

The instructions given in this document describe the assembly of PrismaSeT switchboards in compliance with certification CEI61439 1 and 2.
Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel.
Failure to follow the assembly instructions is the installer’s responsibility. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material in case of failure to comply with the assembly instructions.

PART LIST

INSTLLATION INSTRUCTION

SAFETY INSTRUCTION

• DANGER
  HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

  • Verify that the cables connected from the Wireless Panel Server are wired to its respective terminal block while being connected onto the incoming cables. Make sure they are not in contact with earthing or ground due to inadvertence or during maintenance operation.
  • Failure to follow these instructions will result in death or serious injury.

• WARNING
  UNEXPECTED EQUIPMENT OPERATION

  • During installation check that the wiring harness is not damaged. If damaged, replace it by SMT10016 spare wiring harness.
  • Failure to follow these instructions can result in death, serious injury, or equipment damage.

• NOTICE
  HAZARD OF EQUIPMENT DAMAGE

  • Disconnect the wiring harness from Wireless Panel Server before the dielectric test.
  • Failure to follow these instructions can result in equipment damage.

• NOTICE
  UNEXPECTED EQUIPMENT OPERATION

  • Verify the integrity and presence of the test port label.
  • Failure to follow these instructions can result in equipment damage.

CIRCUIT TYPE

Recommended

Alternate option

Recommended

Alternate option

NOTICE
HAZARD OF NON COMPLIANCE TO INSTALLATION INSTRUCTIONS

• The LED will switch ON with no alert for 1 phase loss with such wiring due to a probability of residual voltage coming back on the phase from the loads.
• However, if 2 or 3 phase loss occurs, the LEDs will switch OFF and trigger an alert of voltage Loss.
• Failure to follow these instructions can result in false interpretation of the voltage loss.

Recommended

Alternate option

Panel Server Status LED

1. Power supply connected and connection to LoRa network is established.
2. Panel Server LoRa connection tentative.
3. Panel Server in Boot mode. Connection with EPC is not possible.
4. Panel Server not yet connected to Facility Expert App. Push the button and Launch Registration in Facilty Expert to switch to green. This is a natural behavior which occurs during normal operation, and does not affect the functioning of the product.
5. Major malfunction, Panel Server communication with EPC is not possible for diagnose.
6. Major malfunction. Connect Panel Server to EPC to diagnose the issue.
7. Depending on issue, Panel Server may be replaced.
8. Bluetooth enabled, EPC connected to Panel Server.
9. Bluetooth enabled, ready for EPC to connect.

NOTICE
UNEXPECTED EQUIPMENT OPERATION

• Check the antenna placed inside the product before removing the gland plate from the roof.
• Failure to follow these instructions can result in equipment damage.

NOTICE
UNEXPECTED EQUIPMENT OPERATION

• Check the best LoRa reception position before installaing the antenna, refer LoRa installation guide DOCA0203EN.
• Failure to follow result in loss of communication.

ABOUT COMPANY

• Schneider Electric Industries SAS
• 35, rue Joseph Monier
• 92500 Rueil-Malmaison
• France
• www.se.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>