SCOCHE 142MSQSWT 3 In 1 MagSafe Compatible Folding Charge Stand Instruction Manual
- June 1, 2024
- SCOCHE
Table of Contents
SCOCHE 142MSQSWT 3 In 1 MagSafe Compatible Folding Charge Stand
Product Information
Specifications:
- Model: BAASECCHHAARRGETMTMMMS
- Included Elements: ELEMENNTTSS
Product Usage Instructions
Assembly:
Follow the provided assembly instructions carefully to ensure proper setup.
Powering On:
Connect the product to a power source following the designated power input.
Press the power button to turn on the device.
Operation:
Use the control panel or remote (if applicable) to navigate through the
product’s functions and settings.
Maintenance:
Regularly clean the product using a soft, dry cloth. Avoid using harsh
chemicals that may damage the product’s surface.
Frequently Asked Questions (FAQ):
-
Q: How do I troubleshoot if the product does not turn on?
A: Check the power source, ensure all connections are secure,and try a different power outlet. If the issue persists, contact customer support. -
Q: Can I use the product outdoors?
A: This product is intended for indoor use only unless specified otherwise in the user manual. Outdoor use may void the warranty. -
Q: What should I do if I encounter an error code on the display?
A: Refer to the user manual for error code explanations and troubleshooting steps. If needed, contact customer support for further assistance.
3-in-1 Mag Safe® Compatible Folding Charge Stand
INCLUDED ELEMENTS
- A. MagSafe® Compatible Charger for iPhone 12 and Later
- B. Charging Stand (folds for travel)
- C. Wireless Charging Pad for AirPods® Charging Case or Additional Wireless Device
- D. Cable Routing Channel
- E. Illuminated Base with Touch Control
- F. Slide-On Holder for Apple Watch® Magnetic Fast Charger to USB-C (charger not included)
- G. Power Adapter Input (48W power adapter with 5 ft. cable included)
- H. 15W USB-C Charge Port
- I. MagicRing™ Adapter
- J. Mounting Template
- K. Cleaning Wipe
DEVICE SETUP
Getting Started
Unfold the charging stand (A). Connect the included power adapter to the unit
(B), and plug the adapter into a wall socket. The unit will power on
automatically.
Illuminated Base with Touch Control
Touch anywhere on the stand’s neck (C) to control the light as follows:
-
Turn light on/off: Tap once
-
Increase/decrease brightness: Tap and hold
-
Hold 5 seconds for low to high or high to low
-
Disable light feature: Tap and hold for 10 seconds
-
The light feature will not resume function until enabled*
-
Enable light feature: Tap and hold for 5 seconds
Note : The light feature does not indicate if the phone is charging or charged -
Use the battery indicator on the phone’s screen to check the charge status.
Slide-On Holder for Apple Watch®
Note : For use with Magnetic Fast Charger to USB-C (not included).
- Route the charger cable through the opening in the holder (A), and slide the holder onto the charging stand (B).
- Seat the magnetic charger in the holder (C), and route the charger cable into the guide channels in the holder and in the back of the stand (D).
- Plug the charger cable into the USB-C port (E).
USING BASE CHARGE
- MagicRing Installation on Non-MagSafe Devices* Case required. Manufacturing materials do not allow adhesives to bond directly to the device.
- Clean the surface of the case using the supplied wipe. Use the included template to accurately position MagicRing on the device.
Foreign Object Detection (FOD)
If a metal object is detected on either wireless charger (stand or base) the
light surrounding the base will pulse slowly*. When the object is removed, the
normal function will resume.
Note : The FOD light pattern functions even if the light feature has been
disabled (see previous section).
SPECIFICATIONS
- Input: 12V=== 4A, 48W
- Wireless Puck: 5W / 7.5W / 10W
- Wireless Base: 5W / 7.5W / 10W
- USB-C: 5V== 3A, 15W
- LED Light : 3.5W
FCC Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning : changes or modifications to this product not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, under part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used by the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Canadian Compliance Statement
This device contains licence-exempt transmitters)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions: (1) This device may not
cause interference. (2) This device must accept any interference, including
interference that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth
for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
BaseCharge MS How-To Video
Scosche Industries 1550 Pacific Avenue Oxnard, California 93033
Phone : 800-363-4490 x1 /
805-486-4450 × 1
www.scosche.com
©2023 Scosche Industries
Scosche & BaseLynx are trademarks of Scosche Industries.
Other marks or brands are the property of their respective owners,
Devices and or appearance may vary.
Designed in Oxnard, California
SI MSQS 4/23
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>