PROSCENO 108M Series Ultra Speed VDSL2 Extender Installation Guide

PROSCENO 108M Series Ultra Speed VDSL2 Extender

Product Information

Specifications

• Product Name: 108M Series Ultra-Speed VDSL2 Extender
• Version: 1.01
• Power Input: 12 ~ 24VDC
• Interface: 1 x RJ-45 connector for Gigabit Ethernet LAN port, 1 x RJ-45 connector for VDSL2 port
• LED Indicators: PWR, RT, LNK
• DIP Switches: 4 for CFG (Configuration)

Product Usage Instructions

Power Connection

• For 108M/108MI: Input power from DC Jack with a voltage range of 12 ~ 24VDC.
• For 108MI-TB: Input power from Terminal Block with a voltage range of 12 ~ 24VDC by inserting positive and negative wires into V+ and V- contacts.

Front Panel Illustration
The front panel includes interfaces such as RJ-45 connectors for LAN and VDSL2 ports, LEDs for LAN port speed, link status, power status, RT mode activation, and VDSL2 link status, as well as DIP switches for configuration.

LED Indicators
LED indicators on the right side show power status, RT mode activation, and link status. Green indicates various statuses while blinking or being off represents different conditions.
LED indicators on the left side represent line port pin assignments.

DIP Switch Configuration

The DIP switches control functions such as RT/CO, Asymmetric/Symmetric mode, Interleave G.INP mode, and SNR levels (Low/High). Adjust them with caution after turning off the power.

Wall Mounting
Wall mounting is supported by 108MI and 108MI-TB. Use the provided mounting holes for horizontal or vertical wall installation with screws not longer than 3mm.

DIN Rail Installation and Mounting
DIN Rail installation and mounting are available for 108MI and 108MI-TB. Follow the safety instructions and guidelines provided in the manual.

FAQ

• Q: Can the device be powered by both DC Jack and Terminal Block?
  A: Yes, the 108M/108MI models can be powered through the DC Jack, while the 108MI-TB model can be powered through the Terminal Block.

• Q: How do I adjust the DIP switch settings?
  A: Before adjusting the DIP switch settings, ensure that the power is turned off. Follow the instructions in the manual to set the desired configurations.

108M Series Ultra-Speed VDSL2 Extender
Quick Installation Guide

Overview

Combination of any two of 108M, 108MI, and 108MI-TB features a pair of point- to-point solutions utilizing VDSL2 technology for carrying Ethernet data over UTP cables.

Front Panel Illustration
The following interfaces are placed on the front panel:

• 1 x RJ-45 connector for Gigabit Ethernet LAN port
• 1 x RJ-45 connector for VDSL2 port
• 3 x LEDs for LAN port speed and link status
• 1 x LED for power status
• 1 x LED for RT mode activation
• 1 x LED for VDSL2 link status
• 4 DIP Switches for CFG (Configuration)

LED Indicators

LEDs on the right

(Remote)

| CO

(Master)

LNK

| ****

Green

| Slow: Idle| ****

VDSL2 LINK UP

| VDSL2 LINK DOWN
Fast: Training

LEDs on the left

DIP Switch Configuration

DIP

Switch

| Function| On| Off
---|---|---|---
1| RT/CO| RT| CO
2| Asymm/Symm| Asymmetric| Symmetric
3| Mode| Interleave| G.INP
4| SNR| Low| High

Note
The factory default setting of switch 1 is “ON”, other three DIP switches are at “OFF” positions. Before adjusting the DIP switch, ensure that the power has been turned off.

Power Connection

There are two options for power input from the rear panel.

1. 108M/108MI: Input from DC Jack,
2. 108MI-TB: Input from Terminal Block range 12 ~ 24VDC Insert the positive and negative wires into V+ and V- contacts on the terminal block and tighten the wire-clamp screws to prevent the wires from being loosened.

LINE Port Pin Assignments
Two of the eight pins of VDSL2 port are used to connect UTP cable over long distances, pin-out assignments are shown in the table below.

2| Not Used
3| Not Used
4| ANALOG Input/Output
5| ANALOG Input/Output
6| Not Used
7| Not Used
8| Not Used

Wall Mounting
Wall mounting is only supported by 108MI and 108MI-TB.

• At the rear side, two mounting holes are placed for horizontal or vertical wall mounting.
• The length of the screw head and body, must not be longer than 3mm inside the device body.

DIN Rail Installation and Mounting
DIN Rail clip and the three screws are optional accessories, and not included in a standard package. DIN Rail installation and mounting are only featured by 108MI and 108MI-TB.

DIN Rail clip Installation
Fasten the DIN Rail clip to the device using a screwdriver and three screws. Each screw is flat head M3 x 5mm

DIN Rail Mounting

• STEP 1 : Hook the unit over the DIN Rail.
• STEP 2: Push the bottom of the unit toward the DIN Rail until it snaps into place.

DIN Rail Removal

• STEP 1: Push the unit down to free the bottom of the DIN Rail.
• STEP 2: Rotate the bottom of the unit away from the DIN Rail.
• STEP 3: Unhook the top of the unit from DIN Rail.

ATTENTION: Safety Warning

• Disconnect all power from devices before attempting installation.
• This device is intended for installation only in restricted access locations as defined where both these conditions apply:
• Access is through the use of a lock or tool and key, or other means of security, and is controlled by the authority responsible for the location.
• Access can only be gained by service persons or by users who have been instructed about the reasons for the restrictions applied to the location and about any precautions that shall be taken.
• All electric installations must be carried out in accordance with local and national regulations.
• Do not work on the system, connect or disconnect cables during periods of lightning activity.
• The equipment must be connected to earth.
• Shield of RJ45 cables has to be connected to the same earth potential as the equipment.
• Please remove the ground connection lastly if you need to remove the device after installation.
• If the LINE interface is used for the connection between two buildings, all necessary protective measures must be ensured externally.
• This equipment relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 1A is used.

NOTE

Please scan below QR Code to download online resources. Download link:
https://www.proscend.com/en/product/108M.html https://www.proscend.com/en/product/108MI.html

P/N: 604040000081

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>