ideal lux 8I287881 Bento Frame Round Single Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
8I287881 Bento Frame Round Single
Instruction Manual
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Drill a hole into the ceiling with the above dimensions.
Attention, respect the installation spaces as illustrated.
Connect the driver to his own network wires. Warning! Keep double
insulation.
Push diagram (only for 1-10V/PUSH or
DALI/PUSH drivers with dedicated PUSH input) Push diagram (only for DALI/PUSH
drivers without dedicated PUSH input) Re-connect the quick connection cable
to the secondary output (SEC) of the dimmable driver. Pay attention to the
polarities “+” and “-“.
Connect the dimming devices wirings to the dimmable driver input in accordance
with the connection diagrams above. For in-depth information, always refer to
the detailed data sheets of the driver or tot he specific indication placed on
board of it.
insert the Frame into the hole by
passing the driver wire inside. Connect the light Source’s wire – including
the Square reflector support -to the driver’s wire. Insert light Source making
sure the Square reflector supports is well hooked to the Frame. To Make sure
that the the light Source has been blocked you have to hear three times a
“Click” sound.
Choose the optional accessory that suits your needs.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION
SHEET FOR FUTURE REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Choose the Reflector that suits your needs.
Unlock the light Source by pushing the specfic button inside. The
light Source can adjust to a maximum of 30°.
Insert the
Reflector. Be sure to hear a “Click” sound to secure the internal locking
system.
Insert the Reflector. Be sure to
hear a “Click” sound to secure the internal locking system. Warning, Anti-
glare ring assembly will prevent the adjustability of the product.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Drill a hole into the ceiling with the above
dimensions. Attention, respect the installation spaces as illustrated.
Connect the driver to his own network wires. Warning! Keep
double insulation.
Push diagram (only for 1-10V/PUSH or
DALI/PUSH drivers with dedicated PUSH input) Push diagram (only for DALI/PUSH
drivers without dedicated PUSH input) Re-connect the quick connection cable
to the secondary output (SEC) of the dimmable driver. Pay attention to the
polarities “+” and “-“.
Connect the dimming devices wirings to the dimmable driver input in accordance
with the connection diagrams above. For in-depth information, always refer to
the detailed data sheets of the driver or tot he specific indication placed on
board of it.
insert the Frame into the hole by passing
the driver wire inside. Connect the light Source’s wire – including the Square
reflector support -to the driver’s wire.
Insert light Source making sure
the Square reflector supports is well hooked to the Frame. To Make sure that
the the light Source has been blocked you have to hear four times a “Click”
sound. Choose the optional accessory that suits your needs.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Choose the Reflector that suits your needs.
Unlock the light Source by pushing the specfic button inside. The
light Source can oriented to a maximum of 30°.
Insert the
Reflector. Be sure to hear a “Click” sound to secure the internal locking
system.
Insert the Reflector.
Be sure to hear a “Click” sound to secure the internal locking system.
Warning, Anti-glare ring assembly will prevent the adjustability of the
product.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Drill a hole into the ceiling with the above dimensions. Attention,
respect the installation spaces as illustrated.
Connect the driver to
his own network wires. Warning! Keep double insulation. Push diagram (only for
1-10V/PUSH or DALI/PUSH drivers with dedicated PUSH input) Push diagram (only
for DALI/PUSH drivers without dedicated PUSH input) Re-connect the quick
connection cable to the secondary output (SEC) of the dimmable driver. Pay
attention to the polarities “+” and “-“.
Connect the dimming devices wirings to the dimmable driver input in accordance
with the connection diagrams above. For in-depth information, always refer to
the detailed data sheets of the driver or tot he specific indication placed on
board of it.
insert the Frame into the hole by
passing the driver wire inside. Connect the light Source’s wire – including
the Square reflector support -to the driver’s wire.
Insert light Source making sure the Square reflector supports is
well hooked to the Frame. To Make sure that the the light Source has been
blocked you have to hear eight times a “Click” sound. Choose the optional
accessory that suits your needs.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Choose the Reflector that suits your needs.
Unlock the light Source by pushing the specfic button
inside.
The light Source can oriented to a
maximum of 30°.
Insert the Reflector. Be sure to
hear a “Click” sound to secure the internal locking system.
Insert the Reflector. Be sure to hear a “Click” sound to
secure the internal locking system. Warning, Anti-glare ring assembly will
prevent the adjustability of the product.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
Drill a hole into the ceiling with the above
dimensions. Attention, respect the installation spaces as illustrated.
Connect the driver to his own
network wires. Warning! Keep double insulation.
Push diagram (only
for 1-10V/PUSH or DALI/PUSH drivers with dedicated PUSH input) Push diagram
(only for DALI/PUSH drivers without dedicated PUSH input) *Re-connect the
quick connection cable to the secondary output (SEC) of the dimmable driver.
Pay attention to the polarities “+” and “-“.
Connect the dimming devices wirings to the dimmable driver input in accordance
with the connection diagrams above. For in-depth information, always refer to
the detailed data sheets of the driver or tot he specific indication placed on
board of it.
insert the Frame into the hole by
passing the driver wire inside. Connect the light Source’s wire – including
the Square reflector support -to the driver’s wire.
Insert light Source making sure the Square reflector supports is
well hooked to the Frame.
To Make sure that
the the light Source has been blocked you have to hear twelve times a “Click”
sound.
Choose the optional accessory
that suits your needs.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED
ELECTRICIAN
Choose the Reflector that suits your needs.
Unlock the
light Source by pushing the specfic button inside.
The light Source
can oriented to a maximum of 30°. Insert the Reflector. Be sure to hear a
“Click” sound to secure the internal locking system.
Insert the Reflector. Be sure to hear a “Click” sound to
secure the internal locking system.* Warning, Anti-glare ring assembly will
prevent the adjustability of the product.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION
INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR
FUTURE REFERENCE.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN
INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION
SHEET FOR FUTURE REFERENCE. This product is provided with a light source with
efficiency energy class of:
| Light Source Model| Energy Efficiency Class| Light Source
(mA)| Light Source (V)
---|---|---|---|---
8.0217E+12| BENTO 3000K CRI90| F| 250 mA| 30 V DC
8.0217E+12| BENTO 3000K CRI90| F| 350 mA| 30 V DC
ICON
| Replaceable light source by an end-user.
---|---
Replaceable LED light source by an end-user.
Replaceable light source by authorized personnel only.
Non-replaceable light source. Upon end of life of the light source, the whole
product will be replaced.
| Replaceable control gear by an end-user.
---|---
Replaceable light source by authorized personnel only
Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class | Electrical safety guaranteed by the main insulation and an additional protective conduc- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
Via Taglio Destro 32, 30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D, 30036 Santa Maria di Sala (VE) Italy
8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>