ideal lux PL3 D90 Hermes Ceiling Light 3Lt in Satin Brass Installation Guide
- June 1, 2024
- ideal lux
Table of Contents
ideal lux PL3 D90 Hermes Ceiling Light 3Lt in Satin Brass
Product Specifications
- Model: Hermes PL3 D90
- Power: G9 max 3 x 28W
- Voltage: 220~240V, 50/60Hz
- Color Options: BIANCO, OTTONE
- Manufacturer: IDEAL LUX s.r.l.
- Country of Origin : Italy
Product Usage Instructions
Installation
- The lighting fitting should be installed by a qualified electrician.
- Follow the assembly instructions provided in numerical order.
Energy Efficiency Class:
This product is provided with a light source with an energy efficiency
class of F.
Light Source Information
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
Safety Instructions
- Ensure the power supply is switched off before installation or maintenance.
- Use appropriate fixing accessories and comply with regulations for installation.
- Do not look directly at the light source.
Frequently Asked Questions (FAQ)
Q: Can the LED light source be replaced by the end-user?
A: Yes, this product allows for the replacement of the LED light source by
the end-user.
Q: What should I do if the lamp does not turn on?
A: Check and replace the fuse if needed. Always ensure to replace it with a
suitable fuse.
Plafonnier
- G9 max 3 x 28W / 220~240V 50/60Hz
DIMENSION
INSTALLATION INSTRUCTION
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
This product is provided with a light source with efficient energy class of:
LEGENDA ICONE
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Upon the end of the life of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598- 1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing the ceiling.
- This fitting is only suitable for fixing the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class I| Electrical safety guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
Via Taglio Destro 32 30035 Mirano (VE) Italy www.ideal-lux.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>