ideal lux Lugano SP3 Suspension Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux Lugano SP3 Suspension Lamp
Product Specifications
- Model: Lugano SP3
- Socket Type: E27
- Maximum Wattage: 3 x 60W
- Voltage: 220-240V, 50/60Hz
- Colour: BIANCO
- Manufacturer: IDEAL LUX srl
- Country of Origin: Italy
Product Usage Instructions
Assembly Instructions
Follow the assembly instructions by reading the numerical progression provided in the manual.
Installation
The lighting fitting should be installed by a qualified electrician.
Safety Instructions
- Ensure the power supply is switched off before starting the installation or any maintenance.
- Avoid looking directly at the light source.
- Use appropriate fixing accessories for mounting. Only use screws and plugs compliant with regulations.
- If the external power cable is damaged, it should be replaced by the manufacturer, retailer, or a qualified electrician.
- Do not dismantle the LED light source as it is non-replaceable.
Electrical Safety Classes
- Class I: Main insulation with protective earthing. Mandatory grounding is required.
- Class II: Main insulation with double insulation or reinforced insulation. No grounding is required.
- Class III: Electrical safety ensured by very low voltage (below 50 Volts). No grounding is required.
Frequently Asked Questions (FAQ)
-
Q: Can the LED light source be replaced?
A: No, the LED light source in this product is non-replaceable. -
Q: What should I do if the lamp does not turn on?
A: In case the lamp does not turn on, try replacing the fuse. If the issue persists, contact the manufacturer or a qualified electrician for further assistance.
DIMENSION
Suspension lamp
E27 max 3 x 60W / 220~240V 50/60Hz
- 8021696206875 BIANCO
WARNING
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class IL electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l. Via Taglio Destro 32 30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse Via delle Industrie, 8/D 30036 Santa Maria di Sala
(Venezia) 8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>