ideal lux Maracas AP2 Wall Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux Maracas AP2 Wall Lamp
Product Specifications
- Brand: Ideal Lux
- Model: Maracas AP2
- Light Output: G4 max 2 x 2W LED
- Power Supply: 220-240V, 50/60Hz
- Product Code: 8021696200347 OTTONE
Product Usage Instructions
Assembly Instructions
Follow the assembly instructions in numerical order as provided in the
manual.
Installation
The lighting fitting should be installed by a qualified electrician for
safety reasons.
Light Source Information
This product is provided with a light source with an energy efficiency
class of G and a light source of 12 VDC.
Replacement Instructions
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable control gear by an end-user.
FAQ
-
Q: Can the light source be replaced by anyone?
A: The light source can be replaced by end-users according to the instructions provided. -
Q: What should I do if the lamp does not turn on?
A: If the lamp does not turn on, check and replace the fuse if necessary following the manufacturer’s guidelines. -
Q: Are specific accessories required for installation?
A: Yes, every material requires specific fixing accessories. Use appropriate screws and plugs compliant with regulations.
DIMENSION
Wall lamp
G4 max 2 x 2W LED / 220~240V 50/60Hz
- 8021696200347 OTTONE
WARNING
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTOR
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
This product is provided with a light source with efficient energy class of:
- Light Source (V) Energy Efficiency Class
8021696222257 G 12 VDC
INSTRUCTION
-
Replaceable light source by an end-user.
-
Replaceable LED light source by an end-user.
-
Replaceable light source by authorized personnel only.
- Non-replaceable light source.
-
Upon end of life of the light source, the whole product will be replaced.
-
Replaceable control gear by an end-user.
-
Replaceable light source by authorized personnel only.
-
Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- Luminaire is not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
- Class II Electrical safety is guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l. Via Taglio Destro 32 30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse Via delle Industrie, 8/D 30036 Santa Maria di Sala
(Venezia) 8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>