ideal lux 8I250977 Tifone LED Bollard Light 350mm in Anthracite Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux 8I250977 Tifone LED Bollard Light 350mm in Anthracite
Product Specifications
- Brand: Tifone
- Model: PT H35
- LED: 8.5W
- Voltage: 220-240V, 50/60Hz
- Color: Antracite
- Energy Efficiency Class: F
- Manufacturer: IDEAL LUX s.r.l., Italy
Product Usage Instructions:
Installation
- The lighting fitting should be installed by a qualified electrician.
- Follow the assembly instructions in numerical progression.
- Ensure the terminal box IP68 3 x 0.75 mm2 is included for installation.
Light Source Information
This product is provided with a light source with an energy efficiency
class of F.
The light source is replaceable by an end-user.
Control Gear
The control gear is replaceable by an end-user.
Safety Instructions
- Always disconnect the main power supply before installation or maintenance.
- Avoid touching hot surfaces on the product.
- Ensure proper mounting accessories are used for installation.
Frequently Asked Questions (FAQ)
-
Q: Can the LED light source be replaced by anyone?
A: Yes, the LED light source is replaceable by an end-user. -
Q: What is the energy efficiency class of the light source?
A: The light source has an energy efficiency class of F.
Tifone PT H35
Floor lamp
LED 8,5W / 220~240V 50/60Hz – 8021696250977 ANTRACITE
DIMENSION
SAFETY
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION.
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
This product is provided with a light source with efficiency energy class of:
EAN 8021696250977
- Light Source Model TIFONE
- Energy Efficiency Class F
- Light Source (mA) 700 mA
- Light Source (V) 9 V DC
LEGENDA ICONE
-
Replaceable light source by an end-user.
-
Replaceable LED light source by an end-user.
-
Replaceable light source by authorized personnel only.
-
Non-replaceable light source. Upon end of life of the light source, the whole product will be replaced.
-
Replaceable control gear by an end-user.
-
Replaceable light source by authorized personnel only.
-
Upon end of life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electnician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class | Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the onerating light source
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>