ideal lux 8I208794 Wall Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
ideal lux 8I208794 Wall Lamp
Specifications
- Model: Pan AP2
- Max Wattage: 2 x 40W
- Voltage: 220-240V, 50/60Hz
Dimensions
- Length: 580mm
- Width: 250mm
- Height: 170mm
- Manufacturer: IDEAL LUX s.r.l.
- Country of Origin: Italy
Installation
The lighting fitting should be installed by a qualified electrician. Follow
the assembly instructions by reading the numerical progression provided in the
manual.
Safety Instructions
- Always disconnect the power supply before installation or maintenance.
- Avoid looking directly at the light source.
- Use appropriate fixing accessories and comply with safety regulations.
- Do not disassemble the LED light source.
- If the lamp does not turn on, replace the fuse.
- Ensure proper grounding as per the safety class requirements.
Cleaning and Maintenance
Regularly clean the fixture with a soft, dry cloth. Avoid using harsh
chemicals that may damage the surface of the product.
FAQ:
Q: Can I replace the LED light source?
A: The LED light source is not replaceable. Do not attempt disassemble it.
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D 30036 Santa Maria di Sala (Venezia) 8.00 – 12.00 /
13.30 – 17.00
Pan AP2
FOLLOW THE ASSEMBLY
INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories.
- Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against vate Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against splashing water.
- Protected against water jets
- Protected against water jets. Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>