ideal lux 8I012889 Firenze Table Lamp Instruction Manual
- June 1, 2024
- ideal lux
Table of Contents
8I012889 Firenze Table Lamp
Firenze TL1
REV 18/04/2023
8I012889 Firenze Table Lamp
Table lamp
E14 max 1 x 40W / 220~240V 50/60Hz
– 8021696012889 BIANCO
– 8021696020853 ORO 
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS
ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE
REFERENCE.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the Earthing is obligatory.
- Class II Electrical safety guaranteed by the main insulation and a double or reinforced Earthing not necessary.
- Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing
- Not protected
- Protected against solid objects greater than 50
- Protected against solid objects greater than 12
- Protected against solid objects greater than 2,5
- Protected against solid objects greater than
- Dust protected.
- Totally protected against dust
- Not Protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against
- Protected against splashing
- Protected against water
- Protected against strong water
- Protected against temporary
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating
- Caution, risk of electric shock.
- Do not stare at the operating light
IDEAL LUX s.r.l.
IDEAL LUX Warehouse
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>