ideal lux D061 Gemini LED Pendant Light Instruction Manual

: June 2, 2024
: ideal lux

Table of Contents

ideal lux D061 Gemini LED Pendant Light
Product Usage Instructions
Frequently Asked Questions
DIMENSION
ASSEMBLY INSTRUCTIONS
SAFETY INSTRUCTIONS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ideal lux D061 Gemini LED Pendant Light

Product Specifications

Brand: Gemini
Model: SP D061 On-Off
Power: LED 48W
Voltage: 220-240V, 50/60Hz
Available Colors: BIANCO, NERO, OTTONE
Manufacturer: IDEAL LUX srl
Country of Origin: Italy

Product Usage Instructions

Installation:

The lighting fixture should be installed by a qualified electrician.
Follow the assembly instructions provided by reading the numerical progression.

Light Source Replacement:

The light source is replaceable by an end-user.
For LED light source replacement, it can also be done by an end-user.
Some light sources are replaceable only by authorized personnel.

Control Gear Replacement:

The control gear can be replaced by an end-user in some cases.
In certain situations, the control gear replacement must be done by authorized personnel.

Frequently Asked Questions

Q: Can the light source be replaced by the user?

A: Yes, the light source can be replaced by the end-user in most cases. For specific situations, it may require authorized personnel.

Q: What are the available colors for this model?

A: The available colors are BIANCO, NERO, and OTTONE.

Q: Is the control gear replaceable?

A: The control gear can be replaced by the end-user in some instances. However, for certain cases, it should be replaced by authorized personnel.

Lampada a suspension Suspension lamp

LED 48W / 220~240V 50/60Hz
– 8021696247250 BIANCO
– 8021696247267 NERO
– 8021696269832 OTTONE

DIMENSION

ideal-lux-D061-Gemini-LED-Pendant-Light-fig-4

ASSEMBLY INSTRUCTIONS

FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION.

ideal-lux-D061-Gemini-LED-Pendant-Light-fig-5

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

This product is provided with a light source with effificiency energy class of:

ideal-lux-D061-Gemini-LED-Pendant-Light-fig-6

ideal-lux-D061-Gemini-LED-Pendant-Light-fig-7

SAFETY INSTRUCTIONS

This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
Always isolate power before commencing installation, maintenance or repair.
The luminaire contains certain parts which can be very hot.
Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
Always tighten the screws firmly to avoid contact problems.
This fitting should only be installed indoors.
Luminaires not suitable for recessed on normally flammable surfaces.
Luminaire not suitable for direct mounting on normal flammable surfaces.
This fitting is only suitable for fixing to the ceiling.
This fitting is only suitable for fixing to the wall.
The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
Only use lamps which do not exceed the maximum specified wattage.
Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
Class | Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation.
Earthing not necessary.
Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
Not protected.
Protected against solid objects greater than 50 mm.
Protected against solid objects greater than 12 mm.
Protected against solid objects greater than 2,5 mm.
Protected against solid objects greater than 1mm.
Dust protected.
Totally protected against dust infiltration.
Not protected.
Protected against vertically falling water drops.
Protected against water drops falling with a maximum angle of 15° to the vertical axis.
Protected against rain.
Protected against splashing water.
Protected against water jets.
Protected against strong water jets.
Protected against temporary immersion.
Protected against prolonged immersion.
Luminaire not suitable for covering with thermally insulating material.
Caution, risk of electric shock.
Do not stare at the operating light source.