Ideal Lux PT D74 Djambe Floor Lamp Instruction Manual
- June 2, 2024
- ideal lux
Table of Contents
Ideal Lux PT D74 Djambe Floor Lamp
Product Information
- Specifications:
- Model: DJAMBE PT D74
- LED: 18W
- Voltage: 220-240V, 50/60Hz
- Colour Options: COFFEE (8021696293417), NERO (8021696293424)
Product Usage Instructions
- Assembly and Installation:
- Follow the assembly instructions provided in the manual by reading the numerical progression.
- The installation of this lighting fixture should be carried out by a qualified electrician.
- Light Source Information:
- This product comes with a replaceable light source with energy efficiency class F.
- The light source is rated at 300 mA and 54 V DC.
- User Replaceable Parts:
- The light source can be replaced by the end-user.
- The LED light source is also user-replaceable.
- The control gear can be replaced by the end-user.
FAQs
Q: Can the LED light source be replaced by anyone?
A: Yes, the LED light source is user-replaceable, but make sure to follow safety guidelines.
Q: Is it safe to install the lighting fixture without a qualified electrician?
A: It is recommended to have a qualified electrician install the lighting fixture for safety reasons.
Q: What should I do if the external power cable is damaged?
A: If the external power cable is damaged, it should be replaced only by the manufacturer, retailer, or a qualified electrician.
MORE INFO
- Floor lamp
- LED 18W / 220~240V 50/60Hz
- 8021696293417 COFFEE
- 8021696293424 NERO
DIMENSION
FEATURE
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
Non-replaceable light source: at the end of its life, the lamp must be disposed.
- This product is provided with a light source with efficient energy class of:
EAN
- 8021696293417
- 8021696293424
Light Source Mode
- DJAMBE PT D74
Energy Efficiency Class
- F
Light Source (mA)
- 300 mA
Light Source (V)
- 54 V DC
ICON LEGEND
Replaceable light source
Replaceable LED light source by an end-user.
Replaceable light source by authorized personnel only.
Non-replaceable light source. Upon the end of the life of the light source, Sorgente luminosa non sostituibile.
Replaceable control gear by an end-user.
Replaceable light source by authorized personnel only.
Upon the end of the life of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems. This fitting should only be installed indoors.
- Luminaires are not suitable for recessed on normally flammable surfaces.
- The luminaire was not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing the ceiling.
- This fitting is only suitable for fixing the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps that do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
- Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
- The main insulation and a double or reinforced insulation guarantee class Il Electrical safety. Earthing is not necessary.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
- Class Ill Electrical safety is guaranteed by a very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 15° to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- It is protected against strong water jets.
- You are protected against temporary immersion.
- They are protected against prolonged immersion.
- Luminaire is not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
CONTACT
- IDEAL LUX s.r.l.
- Via Taglio Destro 32
- 30035 Mirano (VE) Italy
- www.ideal-lux.com.
- IDEAL LUX Warehouse
- Via delle Industrie, 8/D
- 30036 Santa Maria di Sala (Venezia)
- 8.00 – 12.00 / 13.30 – 17.00
- REV 17/10/2023
Read User Manual Online (PDF format)
Loading......