YISENCE 801B15 Double Screen Waterproof Digital Camera User Manual

YISENCE 801B15 Double Screen Waterproof Digital Camera User Manual

MAIN FEATURES

• 3 meters waterproof, photo capture and video recording under water
• 2.7K 2688×1520, FHD 1920×1080, HD 1280x720P,
• Max. 48M pixels
• Convenient dual screens, 1.8 inch front screen, 2.7 inch TFT rear screen
• Face detection, image stabilization, web cam function, various scene modes
• 16x digital zoom
• High speed continuous shooting
• Built-in speaker, microphone
• Micro SD card support up to 128GB (not included)
• Built-in LED flash

Preparation before use

Please install the lithium battery provided with your camera before first use.

1. Slide the battery cover on the bottom of the camera:
   

2. Please install the battery in a right direction

3. Close battery cover

Note:
Please remove the battery when you know the camera will not be used for extended periods.

Charging the lithium battery

Connect the camera to your computer via USB. The green LED illuminates to indicate charging is in progress. The LED will switch off to indicate when the battery is fully charged.

Computer requirements Windows 7/XP3

• Your computer should have the following minimum requirements in order to transfer photos and videos:
• Windows7/XP system or more higher Pentium series processor
• 128MB memory / 150MB available disk space / USB Interface
• Recommended display resolution: 1024×768 resolutions.16 bit color or higher.

Computer requirements – Windows Vista

• If using Windows Vista your computer should have the following minimum requirements in order to transfer photos and videos:
• 800 MHZ processor and 512MB system memory
• 20GB Hard disk with at least 16GB available space
• Support for SVGA graphics
• USB I nterface

Computer requirements – Mac

• Power Macintosh G3 500 MHZ or higher configuration
• Mac OS X version or 10.5.x or more earlier version
• 256MB or more system memory with 150MB available disk space
• 800×600 or higher display resolution

CAMERA OVERVIEW

Icons: Battery Power

Full

Half

Low

Quality

Common

Fine

Super Fine

Flashing Light

Flash On

Auto Flash

Flash Off

Mode

Photo

Playback

video

Self-timer 10s

Self-timer 5s

Self-timer 2s

Self-timer off

Digital Zoom

Protect

Protect

Anti-shake

Anti-shake On

Anti-Shake Off

Scenes

Auto

Scenery

Portrait

Night scenery

Night portrait

High Sensitivity

Sport

Beach

Party

INSTALLING MICRO SD CARD

The camera supports Micro SD memory card up to 128GB Max. (not included).
The camera’s internal memory only stores one photo for testing purposes.
Please insert a Micro SD card into the memory card slot before use, being careful to ensure that the card is installed correctly.
When inserted the card correctly will slide into place smoothly and a ”Click” sound will confirm that it is locked in place. A Micro SD card icon will display on the LCD screen to confirm the camera has detected the card.
To remove the card simply press firmly and it will pop out of the memory card slot.

Note:

1. All photos will saved on the Micro SD card once the Micro SD card installed.
2. Formatting will delete all data on the memory card.
3. Please do not remove the Micro SD card when formatting as this may damage the card.

Turning on the camera

Press the power key on the top of camera to turn on the camera.
The LCD screen will activate to confirm the camera is working.

Photo capture mode

After turning the camera on, the icon will be displayed on the LCD screen to confirm the camera is in photo mode

Switching between displays

To switch between the front and rear screens press the ‘Display screen switching Key’. Each press of this button will activate the front 1.8” screen and rear 2.7” screen in turn.

PHOTO SHOOTING

To capture a photo press the shutter key.
There will be a slight delay while the photo is stored on the memory card.
After taking a photo, the number displayed on the screen indicates how many more photos can be taken considering the current settings and the size of the memory card installed in the camera at that time.
A message will be displayed on the screen when the SD card is full.
To continue, please transfer all data on the SD card to your computer or insert a new memory card.

Digital zoom

Your camera features a 16x digital zoom.
Press the up button to zoom in and the down button to zoom out.

Built-in Flash

Press the ‘Flash’ key to activate the various flash modes.
The icon indicates ‘Flash Off’. The flash will not operate when this mode is selected.
The icon indicates ‘Auto Flash’ mode and the camera will activate the flash automatically if required in low light conditions.
The icon indicates ‘Flash Mode’ and the flash will operate every time a photo is taken

Scenes

The following scene modes are available to facilitate photo capture in different environments:
Auto, scenery, portrait, night scenery, night portrait, portrait, high sensitivity, sports, beach, party.
If required, you can select a mode that matches the condition best that you are shooting in.

Press the power key to turn on camera, The icon will be displayed on top left of the LCD display

1. Press the menu key

2. Press the left/right keys to choose ‘Scene’ icon

3. Press up/down key to select your preferred scene.
   Auto, scenery, portrait, night scenery, night portrait, portrait, high sensitivity, sports, beach, party.

4. Press OK to confirm.

Selection the photo resolution

1. Press the menu key

2. Press left/right key to select photo size icon ‘MP’.

3. Press the up/down key to choose:
   (48M) 8000×6000 , (30M) 6400×4800 , (24M) 5600×4200 , (20M) 5200×3900 ,
   (16M) 4608×3456 , (12M) 4000×3000 , (8M) 3264×2448 , (7MHD) 3648×2048,
   (5M) 2592×1944 , (3M) 2048×1536 , (2MHD) 1920×1080,

4. Press the OK key to confirm your selection. The photo size icon will be displayed on the LCD screen

Anti-shake

Your camera features an anti shake function to deliver better photo quality when a tripod is not being used.

1. Press the Menu key
2. Press the left/right keys to select anti shake icon
3. Press the up/down key to select anti shake on/off
4. Press OK to confirm your selection,
5. The icon will be displayed on the LCD screen to confirm anti-shake is activated.

Face detection

To activate the face detection function.

1. Press the Menu key
2. Press the left/right keys to select the face detection icon
3. Press the up/down keys to select face detection on/off.
4. Press OK key to confirm your selection.

Continuous shooting

The continuous shooting function allows you to capture 6 individual photos in rapid succession with just one press of the shutter button.

1. Press the Menu key
2. Press the left/right keys to select continuous shooting icon
3. Press the up/down keys to select continuous shooting on/off
4. Press OK key to confirm your selection.

Please Note:

When using the ‘Continuous Shooting’ function, the photo resolution automatically changes to VGA.

Self timer

1. Press the Menu key.
2. Press the left/right keys to select the self-timer icon
3. Press the up/down keys to review the self-timer options.
4. Press the OK key to confirm your selection.

SETTINGS

The camera with 21 different setting options.
EV, ISO, White balance, Sharpness, Quality, Effects, Setting Time, Auto Shut down, Language, Frequency Format, Default, Mule mode, Light detect, Sensitivity, Continuous shooting, Anti shake, Photo size, Scene option, Self- timer, Face Detection.

1. Press the Menu key to enter the settings menu.
2. Use the left/right key to select.

The following different settings can be adjusted. Exposure

Adjusts your photos brightness.

1. Press the up/down keys to select the Exposure option.
2. Press the OK key to enter the sub-menu.
3. Press the up/down keys to select EV(+3 to -3).
4. Press the OK key to confirm and save your selection.
   The relative icon will be displayed on the LCD screen.

ISO

This is a special function for when the light source is insufficient, but the environment you are shooting in may not allow for use of the flash.

1. Press the up/down keys to select the ISO option under the settings menu.
2. Press the OK key to enter the ISO sub menu.
3. Press the up/down keys to select the ISO: Auto/100/200/400.
4. Press the menu key to save. The relative icon will be displayed on the LCD screen.

White balance

This option adjusts the photo color and can be adjusted according to light source.

1. Press the up/down keys to select White Balance option under setting menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select: Auto/Daylight/Cloudy/Flourescent/Incandescent
4. Press the OK key to confirm and save your selection.

Sharpness

The function permits the user to adjust the sharpness of the photo so that the edge is clearer or softer.

1. Press the up/down key to select the sharpness option under setting menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select: sharp/common/ soft
4. Press the OK key to confirm and save your selection.

Quality

This function adjusts the overall quality of your photo.

1. Press the up/down keys to select the quality option under settings menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select: super fine/fine/ common
4. Press the OK key to confirm. The relative icon will be displayed on the LCD screen.

Effects

1. Press the up/down key to select the Effects option under setting menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select: Common/Black/Old-fashioned/Red/Green/Blue/Sun set/Warm/Cold.
4. Press the OK key to confirm and save your selection.

Auto shut down

Please Note: The default setting for auto shut down for camera is 3 minutes.

This can be adjusted as follows:

1. Press the up/down key to select the auto shut down option.
2. Press the OK key to enter the auto shut down sub menu.
3. Press the up/down keys to select: 1min/3mins/5mins/Off
4. Press the OK key to confirm and save your selection.
   Note: If you choose ‘Off’, the camera will not auto shut down until the battery runs out of charge.

Sound

1. Press up/down key to select sound option under setting menu.
2. Press the OK key to enter the sound menu.
3. Press the up/down keys to select On/Off.
4. Press the OK key to confirm and save your selction.

Frequency

1. Press he up/down key to select the Frequency option under setting menu.
2. Press the OK key to enter the frequency sub menu.
3. Press the up/down keys to select: 50Hz/60Hz.
4. Press the OK key to confirm and save your selection.

Formatting the memory card

Note: Formatting your memory card deletes all data and files on the card.
Please ensure any files are saved before formatting

1. Press the up/down keys to select the Format option under the setting menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select: Yes/Cancel.
4. If you select cancel, press the OK key to confirm. The camera will return to photo mode
5. Alternatively press the OK key to confirm the Format.

Factory default settings

You can restore you cameras settings to the factory default – PLEASE NOTE: all user defined settings will be lost unless they match some of the default settings.

1. Press the up/down keys to select factory default option under settings menu.
2. Press the OK key to enter the sub menu.
3. Press the up/down keys to select factory default or Cancel
4. If you select Cancel, press the OK key to confirm, the camera will revert to photo mode.
5. Alternatively select YES to continue
6. Press the OK key to confirm your selection.

VIDEO RECORDING MODE

Press the Mode key to activate the video recording mode.
Press shutter key to start recording
The video icon will show on top the left of the LCD screen.
The recording time will show on top right of the LCD screen
The red ‘Recording’ icon will flash to confirm that video is currently being recorded.

Note: Your video can be viewed on your camera using Playback mode.

After reaching a max. video recording time of 29 minutes the camera will automatically stop. It can only be restarted manually.

Playback mode
Press the Mode key to enter playback mode.
In playback mode the icon will show on LCD screen.
Using Playback mode you can view photos and video files currently saved on the memory card.
You can also rotate, protect, delete and cut images.
Video files can be protected or deleted.

Note:

1. Files will not be displayed on the LCD screen if there are no photos or videos saved on the memory card.
2. Please set your video recording settings under Video Recording mode.

USING PLAYBACK MODE FUNCTIONS

Select a photo to rotate, protect, delete, cut, slide play or print.

Rotate

1. Press the Menu key in playback mode.
2. Press the left/right keys to select picture, then press ok to confirm.
3. Press the left/right keys to select the Rotate function.
4. Press the up/down keys to select: 90º /180º /270º /cancel.
5. Press the OK key to confirm your selection.

Slide Show Playback
You can choose how long you want each photo to be displayed on the screen when using the preview mode.
Option (in seconds): 3s/5s/10s

Protect
Protect images and videos to avoid deleting them by accident.

1. Press the Menu key in playback mode.
2. Press the left/right keys to select picture, then press ok to confirm.
3. Press the left/right keys to select the Protect icon
4. Press the up/down keys to select: lock/unlock.
5. Press the OK key to confirm,
6. When viewing photos or videos, protected files will display a lock icon on the screen.

Delete
To delete one or all unprotected images or videos.
In photo/video mode, press delete key to delete the last photo/vodeo.
In Playback mode

1. Press left/right to choose the video/photo,
2. Press the OK keys to open menu,
3. Press left/right to select the Delete function,
4. Press the up/down keys to select: This image/All images /Format/Cancel.
5. Press the OK key to confirm your selection
6. Press the up/down keys to select: Yes/No
7. Press the OK key to delete.

Print
Photos can be printed to any Pict Bridge enabled printer

1. Select a photo to be printed
2. Press the Menu key.
3. Press the left/right keys to select the Print icon
4. Press the up/down keys to select: Print/Cancel.
5. Press the OK key to enter the print option
6. Should wireless printing fail please connect the camera to your printer via a USB cable.

Play video file
Select the video to be played.
Press the shutter button to start playback.
Press the Up key to stop playback

MANUAL TRANSFER OF PHOTO AND VIDEO FILES TO COMPUTER

1. Turn on the camera,
2. Select playback mode
3. Connect the camera to a computer via a USB cable,
4. The removable disc image will pop up on the screen as shown below
5. Click the removable disk to view the photos, which will be stored in the sub file of DICM.
6. You can the copy and paste the photos to your chosen folder or location.
   

COMMON PROBLEMS AND SOLUTIONS

Q: What shall I do? I took some photos, but the computer does not recognize

my camera.

A: First of all please make sure you have taken the photos. Take some photos for testing, then try to download them to your computer. Alternatively please try inserting the memory card directly into your computers card reader if available or by using an external card reader that can be connected to your computers USB port. Please ensure your computer meets the minimum requirements as detailed in this user manual.

Q: How to ensure I won’t miss any important photos

A: As all photos will be stored to the micro SD card inserted in your camera please ensure that there is always enough space available on the card to allow you to take photos. It is recommended that you upload the photos stored on the card to your PC regularly to make more room in the memory card and also as a back up for your files.

Q: Whether my device will be working in MAC system.

A: The device can be worked as a removable disk, Mac OSX (10.5x or higher version)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>