Sofary Lighting 3QFMQBH94687I7 Gold Chandelier for Dining Room Instruction Manual
- May 15, 2024
- Sofary Lighting
Table of Contents
Sofary Lighting 3QFMQBH94687I7 Gold Chandelier for Dining Room
Specifications:
- Item Number: 3QFMQBH94687I7
- Voltage: 120V
- Maximum Wattage: Type B, Max 40W per bulb
Product Usage Instructions
Tools Required:
Before starting assembly and installation, please prepare the needed tools:
(Not Included)
- Round mounting plate (1)
- Green ground screw (1)
- Canopy (1)
- Loop (4)
- Knob nut (2)
- Quick link (2)
- Stem
- Arm (1)
- Socket (5)
- Screw (15)
- Glass shade (5)
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and ensure all parts and accessories are included.
- Pass fixture wires through one side of the stems and screw the chosen stems onto the top of the arm.
- Pass the fixture wires through loops and canopy.
- Mount the fixture ensuring that the gap between the mounting plate and canopy does not exceed 3/16 inch.
- Connect wires following the provided chart. Note that the ground wire is bare copper wire.
- Twist wires together with plastic wire connectors and wrap each connector with electrical tape.
- Install bulbs (not included) without exceeding the maximum wattage recommended on the socket.
- Ensure everything is properly installed before turning on the light.
Cleaning Instructions:
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner, avoiding abrasive materials.
FAQ:
-
Q: Can I use bulbs with a wattage higher than 40W per bulb?
A: No, it is recommended to use bulbs with a maximum wattage of 40W per bulb to prevent damage to the fixture. -
Q: What should I do if I encounter gaps between the mounting surface and canopy?
A: Any gaps exceeding 3/16 inch should be corrected as required before installation to ensure proper mounting. -
Q: How do I order replacement parts?
A: Keep this sheet for future reference and order parts using the exact wording from the illustration at the place of purchase.
Item Number: 3QFMQBH94687I7
WARNING
(To reduce the risk of fire, electric shock, or personal 1in.juWrey )suggest
installation by a licensed electrician.
-
Please read the instructions carefully and save it as you may need it at a later time.
-
Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position. -
The mounting surface should be clean, dry, flat, strong enough, and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
-
Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type B, with a max of 40W per bulb.
7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as
below picture
PARTS TYPE & QTY INCLUDING
- (C) Round mounting plate (1)
- (D) Green ground screw (1)
- (E) Canopy (1)
- (F) Loop (4)
- (G) Knob nut (2)
- (H) Quick link (2)
- (I) Stem
- (J) Arm (1)
- (K) Socket (5)
- (L) Screw (15)
- (M) Glass shade (5)
ACCESSORIES & QTY ENCLOSED:
- (A) Plastic wire connector (3)
- (B) Mounting screw (2)
ASSEMBLY & INSTALLATION INSTRUCTIONS
-
Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
-
Make preinstallation
-
Step A1 » According to your desired fixture height, choose and use stems (I). Pass fixture wires through one side of the stems (I), and screw the chosen stems (I) onto the top of arm (J).
-
Step A2 » Attach quick links (H) to loops (F) on canopy (E) and the top of stems (I). Carefully pass the fixture wires through loops (F) and canopy (E).
-
Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position. » Place the wall switch in the “OFF” position. -
Make installation
-
Step B1 » Unscrew knob nuts (G) from mounting plate (C).
-
Step B2 » Attach mounting plate (C) to the outlet box with mounting screws (B).
-
Step B3 » If needed, shorten the fixture wires length. At this point, the remaining wire length measured above the mounting plate (C) is at least 6″.
-
Step B4 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box. -
Step B5 » Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening knob nuts (G) onto pre-assembled screws on mounting plate (C).
NOTE: canopy (E) should be snug against the ceiling with knob nuts (G).
If not, remove canopy (E), adjust the threaded length of preassembled mounting screws on the mounting plate assembly (C): -
First, unscrew the preassembled hex nuts.
-
Then, screw the preassembled mounting screws in or out of the mounting plate (C).
-
When the secure length is achieved, tighten the preassembled hex nuts and back to Step B5.
-
Step B6
-
Carefully place glass shades (M) on sockets (K), and secure them with screws (L).
-
Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
-
Check everything is already installed properly, then you can turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustrations when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.