VOKALEN TWSBT013 Hybrid ANC TWS Earbud User Guide

User Guide Air Pro
Quick Start Guide
Designed in CANADA

APP

Download the Vokalen app to enhance your experience (ambient sound modes, HearID sound, gaming mode, firmware update, and more).

Before Use

Activate your earbuds

Open the charging case, press and hold the case button for 3 seconds

Bluetooth pairing

Open the charging case.
Select “Air Pro” from your device’s Bluetooth list.
When use again, the earbuds will automatically reconnect to the last connected device.
For FAQs and more information, please visit : vokalen.com/support

https://qr-codes.io/KfAI8k

Power ON/OFF

Power ON: Open the charging case, the earbuds will power on automatically
Power OFF: Put the earbuds into the charging case and close the cover, the earbuds will power off automatically.

Charging

Fully dry off the earbuds and the USB-C charging port before charging.
For wireless charging, position the charging case at the center of your wireless charger horizontally.

Touch Control

The controls setting can be customized in the Vokalen app. X1: Tap once
X2: Tap Twice
X3:Tap Triple
2s: Tap and hold for 2 seconds

| Play/Pause
---|---
| Previous Song
| Next Song
| Answer
| Reject
| Hang up
| Active Noise Cancellation mode
| Voice assistant
| Previous Song
| Next Song

Smart Detection

Playback will automatically pause when an earbud is removed and will resume once you wear it.

LED Guide Earbud Battery level check Manual Setup
Connect to a new bluetooth device
Manual Setup
**** Factory Reset

Firmware update You will get a notification for new firmware when connecting earbuds to Vokalen app. Keep earbuds in open charging case during update. Ensure they’re charging and avoid using them.

SPECIFICATION

Specifications are subject to change without notice.

FCC/IC
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However,there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit differentfrom that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician forhelp.
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.
FCC ID : MV3-TWSBT013
IC : 9029A-TWSBT013 HVIN: Air Pro
FCC
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance.
The device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA). These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the head is 0.542W/kg（Left ear）and 0.580W/kg（Right ear)
IC
The device is designed to meet the requirements for exposure to radio waves established bythe Innovation, Science and Economic Development Canada’s. These requirements set aSAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reportedunder this standard during product certification for use whenproperly worn on the head is 0.542W/kg（Left ear）and 0.580W/kg（Right ear)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>