ideal lux PL3 King Ceiling Light Instruction Manual
- May 15, 2024
- ideal lux
Table of Contents
ideal lux PL3 King Ceiling Light
Product Information
Specifications:
- Model: King PL3
- Power: G9 max 3 x 40W
- Input Voltage: 220~240V 50/60Hz
- Available Colors: CROMO, ORO
- Energy Efficiency Class: F
- Manufacturer: IDEAL LUX s.r.l.
- Manufacturer Address: Via Taglio Destro 32, 30035 Mirano (VE) Italy
- Manufacturer Website: www.ideal-lux.com
Product Usage Instructions
- Ensure the lighting fitting is installed by a qualified electrician.
- Follow the assembly instructions by reading the numerical progression carefully.
- Refer to the legend icons for information on replaceable parts by end-users or authorized personnel.
- For safety, always disconnect the power supply before installation or maintenance.
- Use appropriate fixtures and fittings for installation according to regulations.
- If the lamp does not turn on, check and replace the fuse if necessary.
FAQ:
-
Q: Can the LED light source be replaced by the end-user?
A: No, the LED light source is non-replaceable. Only authorized personnel should handle its replacement. -
Q: What should I do if the lamp is damaged?
A: If the lamp is damaged, the external power cable should be replaced by the manufacturer, retailer, or a qualified electrician. -
Q: How do I know if the lamp is suitable for outdoor use?
A: Check the IP rating of the lamp. Higher IP ratings indicate better protection against dust and water ingress, suitable for outdoor use. -
Ceiling lamp
-
G9 max 3 x 40W / 220~240V 50/60Hz
- 8021696075389 CROMO
- 8021696075402 ORO
WARNING
ASSEMBLY INSTRUCTIONS
FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE
This product is provided with a light source with efficiency energy class of:
EAN Energy Efficiency Class
8021696209043 F
LEGENDA ICONE
- Replaceable light source by an end-user.
- Replaceable LED light source by an end-user.
- Replaceable light source by authorized personnel only.
- Non-replaceable light source. upon end Of life Of the light source, the whole product will be replaced.
- Replaceable control gear by an end-user.
- Replaceable light source by authorized personnel only.
- Upon end Of life Of the control gear, the whole product will be replaced.
SAFETY INSTRUCTIONS
- This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-1).
- This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
- As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
- If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
- Always isolate power before commencing installation, maintenance or repair.
- The luminaire contains certain parts which can be very hot.
- Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
- Always tighten the screws firmly to avoid contact problems.
- This fitting should only be installed indoors.
- This fitting should only be installed indoors.
- Luminaires not suitable for recessed on normally flammable surfaces.
- Luminaire not suitable for direct mounting on normal flammable surfaces.
- This fitting is only suitable for fixing to the ceiling.
- This fitting is only suitable for fixing to the wall.
- The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
- Only use lamps which do not exceed the maximum specified wattage.
- Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
- Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
- Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
- Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
- This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
- Class I Electrical safety guaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
- Class II Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
- Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
- Not protected.
- Protected against solid objects greater than 50 mm.
- Protected against solid objects greater than 12 mm.
- Protected against solid objects greater than 2,5 mm.
- Protected against solid objects greater than 1 mm.
- Dust protected.
- Totally protected against dust infiltration.
- Not protected.
- Protected against vertically falling water drops.
- Protected against water drops falling with a maximum angle of 150 to the vertical axis.
- Protected against rain.
- Protected against splashing water.
- Protected against water jets.
- Protected against strong water jets.
- Protected against temporary immersion.
- Protected against prolonged immersion.
- Luminaire not suitable for covering with thermally insulating material.
- Caution, risk of electric shock.
- Do not stare at the operating light source.
IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
IDEAL LUX Warehouse
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00