VELECO ZT15 Electric Mobility Scooter User Manual

VELECO ZT15 Electric Mobility Scooter

Product Information

Specifications

• Product Name : TURRIS Electric Mobility Scooter
• Dimensions : 1020 x 1520 x 670 mm (H x L x W)
• Minimum Width of Headland Aisle: 2500 mm
• Permissible Slope : Standard options available
• Tyre Type : Tubeless
• Theoretical Range when Fully Charged : 45-50 km
• Safe Curb Height when Going Downhill: 65 mm

Product Usage Instructions

• Intended Users
  The scooter is designed for users with a weight not exceeding the specified limit, slight motor disability, no uncompensated loss of sight or hearing, and no cognitive impairment. It can also be used by individuals without legs with the assistance of an attendant.

• Operator
  The intended operator is the user who can independently move the scooter without the need for an attendant’s intervention.

• Purpose and Environment of Use
  The scooter is intended to assist patients with slight mobility disabilities in moving outside built-up areas over distances they couldn’t cover on their own. It can be used in urban and non-urban spaces, including road traffic, subject to local regulations

• Scooter Class
  The TURRIS scooter belongs to Class C, allowing for movement outside buildings, longer distances, and overcoming external obstacles.

• Maintenance Instructions
  Use water with car cleaners or detergents for cleaning and maintenance. Avoid solvent-based agents and abrasive materials. Do not tow other vehicles or trailers with the scooter.

FAQ

1. Can the scooter be transported by car or plane?
   The scooter can only be transported by a car equipped with a specialized ramp of the required load capacity.

2. What is the theoretical range when fully charged?
   The theoretical range is between 45-50 km when the scooter is fully charged.

TURRIS
Electric Mobility Scooter

INTRODUCTION

• Thank you for choosing the TURRIS mobility scooter.
• All information contained in this user manual is correct at the time of publication. However, due to the policy of continuous improvement of our products, Veleco reserves the right to make changes at any time. This manual contains information on the operation, maintenance and safety of the mobility scooter, warranty conditions and technical inspections. Veleco insists that these publications should be read carefully and the recommendations should be followed to help new vehicle users ensure satisfactory and safe operation. The manufacturer is not liable for any damage caused by neglected maintenance or improper operation resulting from failure to comply with the recommendations contained in this manual. Compliance with the use and maintenance stated in this manual is a basic condition for the warranty to be valid, therefore we recommend that you read it carefully. Visually impaired people can contact the seller for an easy-to-read version of the user manual.

SPECIFICATION

Availability of instructions for the visually impaired| Due to the target group of users, there is no instruction for the visually impaired.
---|---
Scooter users| Users – people with a weight not exceeding the weight specified in the technical parameters, with a slight degree of motor disability, without uncompensated loss of sight and hearing, without cognitive impairment. It is possible to use the scooter by persons without legs, with the support of an attendant when getting on and off the scooter.
Operator| The intended operator of the scooter is the user – the user moves the scooter independently, without intervention of an attendant.
Purpose and environment of use| Intended use: The scooter enables patients with slight mobility disabilities to move outside built-up spaces at distances that they would not be able to cover on their own, thus fulfilling the function of alleviating the disability.

Environment of us e: The scooter can be used in moderate climates, except during periods of heavy rain and snowfall. The scooter can be used in urban and non-urban spaces, including road traffic, as long as local law regulations allow.

Scooter class| Class C – a scooter with enlarged dimensions, not limited to moving inside buildings, allowing for longer distances and overcoming external obstacles.
Dimensions| 1020x1520x670 (height x length x width [mm])
Minimum width of the headland aisle| 2500 mm
Permissible slope| 17°
Standard options available| Powered by a lead-acid or lithium- ion battery.
Permitted type of tyres| Tubeless
User regulations| Seat adjustment with armrests, mirror adjustment.
The mass of the parts that can be dismantled| Rearview mirrors – 0,200 kg Lead-acid battery (depending on version) – 24,8 kg Lithium-ion battery (depending on version) – 10 kg
Effect of removing tool-less detachable parts on scooter performance| No part detachable without tools.
Can the scooter be mounted in another vehicle as a seat| No
Can the scooter be transported by car or plane| Only a car with a specialized ramp of the required load capacity.
Theoretical range when fully charged|

• 45-50 km
• ATTENTION
• The theoretical range after full charge specified in the scooter specification was measured under ideal test conditions assuming continuous driving in the first speed stage, on a perfectly level surface, with a user weighing 70 kg, without any additional load, at an ambient temperature of 19-22 °C, and optimal humidity in the range of 45-60%.
• Depending on the actual environmental and road conditions, the achievable actual range may be signi ficantly different than the theoretical range given in the specification.

Safe curb height when going downhill| 65 mm
ATTENTION
Descending the curb must be done at a moderate speed!
Information about the programmable controller| The scooter has a built-in programmable controller, programming is not available to the user.
Maintenance instructions| The life of the mobility scooter depends on its use, storage, regular maintenance, servicing and cleaning. Before each ride:

• Check and clean the tyres. If necessary, replace the tyre.
• Check tyre pressure and inflate if necessary.
• Check the finish of the upholstery.
• Check the brakes (efficiency of the brakes, efficiency of the parking brake lock and brake fluid level).
• Check that all screws are tightened securely.
• After starting the motor, check the battery charge level.
• Clean dirt from under the rear of the chassis as it can corrode electrical connections. Storage:
• The scooter should be stored on a flat, stable surface in a well-ventilated and dry place.
• Avoid storing in a humid environment as this may cause problems with the electrical components.
• Do not keep the scooter outdoors as direct sunlight or rain may damage the vehicle.
• Keep the vehicle under a cover to prevent dust formation.
• Batteries should only be stored in dry and well-ventilated rooms at temperatures between +5 °C and +40 °C.
• Preferred storage temperature: +20 °C.

---|---
Cleaning methods to avoid corrosion| Use water with car cleaners used in car washes, or use detergents for cleaning and maintenance of car plastics. Do not use solvent-based agents. Clean only with a cotton cloth or a sponge. Do not use abrasive materials such as cleaners, steel wool.
Use in combination with others with other products| The vehicle has not been designed to tow other vehicles and trailers. Using the vehicle for such purposes could cause sudden loss of stability or traction, which could lead to an accident and injury to the rider.
List of accessories and detachable parts|

• Rearview mirrors User manual
• Lead-acid battery charger Lithium-ion battery charger Lithium-ion battery
• Lead acid battery

Whether and how the scooter can be folded or disassembled for transport or storage| Not applicable.
Transport instructions| It is not possible to transport in an airplane due to the specification of the battery. The car must be properly fitted (ramp).
Weight of the test dummy| 160 kg
Information about the alarm and description of the functions| The electric mobility scooter is equipped with an alarm. Functions : alarm on and off, sound localization, remote start and stop of the vehicle.
Manufacturer| VELECO sp. z o. o.
Address| , 42-202 , POLAND
Model| Turris
Max user weight| 160 kg
Data provided (ISO)
Established standard| | min.| max.
| Total length with footrest| 1520 mm| 1650 mm
| Overall width| 670 mm| 670 mm
| Folded length| 1520 mm| 1520 mm
| Folded width| 670 mm| 670 mm
| Folded height| 1020 mm| 1020 mm
| Total mass| With a lead-acid battery – 103 kg With a lithium-ion battery – 88 kg|

• With a lead-acid battery – 103 kg
• With a lithium-ion battery – 88 kg

| The weight of the heaviest part| Lead-acid battery – 24,8 kg Lithium-ion battery – 10 kg| Lead-acid battery – 24,8 kg Lithium-ion battery – 10 kg
ISO 7176-4| Energy range| 45 km| 50 km
ISO 7176-6| Maximum speed forward| 12 km/h| 12 km/h
| Effective seat depth| 410 mm| 410 mm
---|---|---|---
| Effective seat width| 470 mm| 470 mm
| Backrest height| 360 mm| 360 mm
| The distance between the seat and the footrest step| 430 mm| 430 mm
| Drive wheel diameter| 254 mm| 254 mm
| Turning space| 2500 mm| 2500 mm
The electric mobility scooter complies with the following standards:| Requirements and test methods for static load and fatigue strength (ISO 7176-8).| Yes
Wheelchair power and control systems – requirements and test methods (ISO 7176-14).| Yes
Climatic tests according to ISO 7176-9.| Yes
Fire resistance requirements in accordance with ISO 7176-16.| Yes

USER MANUAL

SCOOTER OVERVIEW

1. Headlamp
2. Front turn signals
3. Front wheel
4. Footrest
5. Charging socket
6. Rear lights
7. Adjustable armrests
8. Backrest
9. Seat
10. Mirrors
11. Rear storage
12. Stop light
13. Lock of the storage compartment under the seat
14. Number plate space
15. Motor
16. Identification plate Number (VIN /chassis)
17. Cupholder
18. Ignition station

The scooter serial number is located on the data plate near the rear right wheel and is stamped on the vehicle frame.
REARVIEW MIRRORS

• Before driving, it is recommended to set the mirrors so that you can see the area behind the user. Correctly adjusting the mirrors allows you to monitor the situation behind the vehicle.
• To adjust the position of the mirrors, turn the nut clockwise to be able to change the position of the mirror. When finished, tighten the nut with a 14 mm wrench. The rear view mirrors of the scooter should be at an angle that allows an unobstructed view of the rear and the corresponding side of the vehicle. For safety reasons, clean the mirrors regularly.

SEAT

• SEAT POSITION ADJUSTMENT (forward/backward).
• Before riding, it is recommended to adjust the seat extension, which improves driving comfort. Adjustments can be made by the user themselves.

To move the seat forwards or backwards:

1. Pull the seat adjustment lever up and hold.
2. Move the seat to the desired position.
3. Release the lever and make sure the seat is locked in place.

Before riding, adjust the seated position and make sure that the seat is securely locked by trying to move the seat forward and backward without pulling the lever. If the seat moves, it is not properly locked.
ATTENTION

• Wrinkles and abrasions that occur naturally with use are not covered by the warranty.
• Belts with metal parts, zippers, or keys carried in your back pocket can damage the seat upholstery.
•  It is recommended to avoid that the seat gets wet as it may affect the structure of the upholstery. Some cleaning products can change the color or its structure. Before washing, check the effect of the selected agent on the less visible part of the upholstery.

ARMRESTS
Both armrests can be moved up and down to allow ease of getting in/getting out of the scooter.
KIEROWNICA

1. Left brake lever (rear brake)
2. Left mirror
3. Light switch – high and low beam
4. Direction indicator and hazard warning lights switch
5. Left handle
6. Drive mode switch (D – forward, R – reverse)
7. Parking brake
8. „Ready” button
9. Thumb accelerator
10. Right handle
11. Right brake lever (front brake)
12. Right mirror
13. Headlight switch – high beam and position lights
14. Drive mode switch (I – II – III gear)

LEFT HANDLE

RIGHT HANDLE

ATTENTION
The hazard warning lights warn other drivers to take extra care when approaching the vehicle. These lights should be used in the event of an emergency repair or when the vehicle is immobilized on the road.
SPEEDOMETER

1. Battery charge indicator
2. Speedometer
3. Gear indicator
4. High beam indicator
5. Direction indicators
6. READY mode indicator – when shown the scooter is ready to go, otherwise the throttle will not work
7. Total mileage counter
8. Warning icons
9. Reverse drive mode indicator

STARTING AND TURNING OFF THE VEHICLE

ADVICE
When parked (more than 1 minute), turn the ignition switch to the „OFF” position. (This will prevent battery exhaustion or damage).
STEERING WHEEL LOCK
To activate the steering lock, move the entire steering column to the left, press the key into the ignition switch and turn it to the lock position.

TYRE PRESSURE

• Recommended tyre pressure is 225 kPa.
• The maximum tyre pressure is 250 kPa.

LOSS OF PRESSURE IN THE TYRES WHILE DRIVING
If one of the tyres loses pressure while driving:

1. Drive straight, release the throttle and allow the vehicle to slow down.
2. Do not immediately apply the brakes or try to pull off the road as this may cause you to lose control of the vehicle. Once the electric mobility scooter has slowed down sufficiently that it is safe to brake and drive off the road carefully, it should be done. Drive as far away from the road as possible and park the vehicle on a solid, level surface.
3. When the vehicle has stopped, turn on the hazard lights.
4. Inflate the tyre as soon as possible or replace it if necessary.

BATTERY

The TURRIS model can be equipped with a lead-acid battery (AKUAGM12SET4) or a lithium-ion battery (DRABALITX). Both of these batteries have a voltage of 48 volts. If your scooter is ordered with a lead-acid battery, you cannot replace it for the lithium-ion one yourself.
WARNING !
If your scooter model has a lead acid battery installed, do not disassemble it without proper technical knowledge. Lead acid batteries are not intended to be removed and charged at home. This is purely an attribute of lithium-ion batteries.
Battery maintenance instructions:

• It should be remembered that too frequent charging of the batteries will lead to irreversible loss of their capacity.

• The charger is equipped with an indicator that signals the end of the charging process.

• To ensure a longer battery life, charge the battery (as soon as the power indicator comes close to discharged) in a full single cycle of approx.6- 8 hours.

• Using the lights affects the battery consumption.

• Too short a battery charging time will result in a gradual loss of capacity, resulting in a shorter travel distance.

• If the battery is opened by the user, the manufacturer’s liability lapses and all claims are voided.

• Do not expose the battery to temperatures below -10 °C or above 50 °C.

• If the scooter is not used for a long time, it should be charged regularly so that you can use it at any time. Unused batteries should be recharged every 3 weeks. Batteries will slowly self-discharge (deep discharge) if they are not used for a long time. Charging them with the included charger becomes impossible.

• WARNING !
  Injury hazard – Remove key before charging.

• WARNING !
  Electric Shock Hazard – Never plug or unplug the plug or cord with wet hands while charging. Do not plug in or unplug the plug or cord when wet. This could result in electric shock. Do not use the charger if its casing is damaged.

• WARNING !
  Risk of fire – do not charge the battery near containers with gasoline, solvents or other flammable materials.

• WARNING !
  Charge the batteries in a well-ventilated area. Do not expose the charger to direct sunlight while charging. Do not charge the battery in wet places or in the rain.

• WARNING !
  Remember to fully charge the batteries each time, otherwise the batteries will lose their life faster than expected by the manufacturer.

• WARNING !

  • If the charger is on and the LED light is not lit, check the main fuse.
  • If the red LED light is off and the battery is flat, the charger or the scooter electrical system is damaged. Contact an authorized service center.

CHARGING THE LEAD-ACID BATTERY

• Fully charge the battery before the first ride.
• The charging socket is located under the driver’s seat.
• Only charge the scooter battery with the supplied charger.

1. Turn the scooter off with the key and remove it from the ignition switch.
2. Open the cover that protects the charging socket.
3. Insert the charger plug into the charging socket.
4. Connect the charger plug to an electrical outlet. The charger will start charging, with a red LED activating to signal this. Riding the scooter is not possible while charging – the immobilizer is active.
5. When the LED turns green, it means charging is complete. Charging time is approximately 6-8 hours.
6. When charging is complete, disconnect the charger from the electrical outlet.
7. Disconnect the charger plug from the charging socket on the scooter and close the charging socket cover.
8. The vehicle is ready for use.

CHARGING THE LITHIUM-ION BATTERY
The lithium-ion battery can be charged in the same way as a lead-acid battery (see chapter CHARGING THE LEAD-ACID BATTERY) or you can pull the battery out of the scooter to charge it in a separate room.

1. Remove the lithium-ion battery from the scooter as instructed in chapter DISASSEMBLY OF THE BATTERIES.
2. Plug the charger supplied with the scooter directly into the battery into the socket.
3. After charging, put the battery back in the scooter and connect the plug to the battery.

• ADVICE
  After charging the vehicle, turn the vehicle on for a few minutes to see if it is sufficiently charged. The effectiveness of the battery depends on the driving style of the mobility scooter (frequency of starting, driving in, driving on uneven terrain). At an optimal temperature range, the battery may be at maximum range, whilst the range may be reduced outside of this optimum.

• WARNING !
  The manufacturer is not responsible for any damage caused by improper charging.

• WARNING !

• Use only genuine batteries.

  • Veleco is not liable for any damage resulting from the use of a battery that has not been supplied by our company.
  • Given maximum range
  • The specification gives an example of a value under ideal conditions: average user weight, average speed and smooth ground.

• Optimum battery charging is in the range of 20-80%. In case of frequent discharges below the optimal value, the service life of the battery may be shortened.

GETTING ON AND OFF THE MOBILITY SCOOTER

GETTING ON

OVERCOMING UNEVEN TERRAIN, STAIRS AND CURBS

ATTENTION

• The scooter has not been designed to tow other vehicles and trailers / semi-trailers. Using the scooter in this way can cause loss of traction, loss of control, and structural damage, which could result in an accident while driving.
• The scooter is a one-seater vehicle and driving with a passenger may also cause loss of traction or control of the vehicle, as well as damage to the vehicle due to exceeding its maximum weight.

STARTING THE MOTOR AND DRIVING A MOBILITY SCOOTER

Before driving:

• It is recommended to fully charge the battery.

• Make sure the seat is locked in the drive position.

• Use the drive mode switch to set the speed to minimum (I). The higher speed values should only be used if the user is fluent in operating and controlling the vehicle.

• We recommend checking that the brake levers work properly.

• We recommend checking that all lights are working properly.

• WARNING !
  If you are using the vehicle for the first time, make sure that it is on level ground and that all wheels are in contact with it.

• WARNING !
  Sudden side winds caused by large vehicles overtaking or being overtaken, exiting tunnels or driving over mountain slopes can also make it difficult to steer the scooter. Remember to reduce speed and watch out for crosswinds.

STARTING THE MOTOR :

1. Turn the ignition key switch to the ON position.
2. Push Ready button on the right handle.
3. Make sure it is safe to start driving.
4. Slowly turn the throttle.

• DRIVING ON A PAVEMENT AND OTHER PAVED SURFACES

  • Be sure to set the drive mode switch to the smallest position when riding the mobility scooter on the pavement. The maximum speed for walking on the pavement depends on the regulations of the given country. Check your country’s laws and regulations before riding. The drive mode switch can be set to the highest value for driving on the road or on private property.

• DRIVING ON SURFACES OTHER THAN PAVED SURFACES

  • Driving on surfaces such as high grass, sand, mud, etc. is not recommended.

• REVERSE DRIVING

  • Driving in reverse requires increased concentration and caution. It is recommended to limit the speed to a minimum. When driving in reverse, the scooter will signal the maneuver.

• UPHILL DRIVING

  • Drive up slopes from the front to avoid tipping over. Check that all wheels always touch the ground (ramps, etc.). It is always recommended to lean slightly forward when climbing high slopes. The battery indicator may move up and down when driving on a slope. Use extreme care when driving on slopes and inclines, and use the brakes if necessary.

• WARNING !

  • Remember that each vehicle has limited stability and traction. Always adjust your speed to the type of road surface, slope and surrounding conditions. If the vehicle is used on the road, be especially careful and follow local regulations. Remember that incorrect driving of the vehicle may cause injury to other people. Pay particular attention to young children in the vicinity of the scooter.

• WARNING !
  Each of these factors affects the number of kilometers traveled. In order to use the mobility scooter as economically as possible and to reduce the costs of charging and repairing the battery, please pay attention to the following points:

  • The electric mobility scooter should run smoothly. Speed up moderately. Do not move the mobility scooter abruptly and do not change the drive mode with the control handle fully twisted and maintain a constant speed. Try to adapt to the traffic on the road to avoid frequent changes of speed. If possible, avoid heavy traffic. Always keep a safe distance from other vehicles to avoid unnecessary braking. This also reduces brake wear. Drive the electric mobility scooter at a moderate speed. The higher the speed of the vehicle, the greater the consumption of the battery.
  • Tyres require maintenance. Maintain the recommended tyre pressure. Incorrect pressure – both too high and too low – causes unnecessary wear on the tyres. Tyre pressure should be checked at least once a month.
  • Maintain the vehicle in good condition. To reduce battery wear and maintenance costs, follow a regular maintenance schedule.
  • Keep the vehicle clean. The electric mobility scooter should be free of corrosive substances. It is very important to prevent mud, dust, ice etc. from accumulating on the undercarriage of the vehicle. This unnecessary burden can cause increased battery wear and corrosion.
  • Do not overload the mobility scooter. Do not transport unnecessary loads. The load increases the consumption of the battery.

BRAKING

1.  Release the accelerator button.

2.  Use the front and rear brakes simultaneously and evenly by pressing the right and left brake levers.

   • WARNING !
     Inexperienced drivers tend to overuse only the rear brake. This results in longer braking distances and can lead to a collision. Using only one brake can lead to wheel spin and loss of vehicle control. You should use both brakes simultaneously.

   • WARNING !
     As the speed of the mobility scooter increases, so does the braking distance. Keep a sufficient and safe distance from vehicles in front of you and other obstacles.

   • WARNING !
     Braking while cornering can lead to a skid and subsequent loss of vehicle control. Before starting the braking maneuver – slow down; avoid risky braking maneuver in a curve.

   • PARKING
     When parking the scooter, the user should use both the parking brake and the steering lock. The parking brake prevents the vehicle from rolling forward or backward by itself when parked on uneven ground.
     To set the parking brake, pull the left brake lever (1) all the way, then push the parking brake pin upwards (2) with your other hand. This locks the handbrake in place.
     To release the parking brake, pull the brake lever all the way and then release it.

UNDER THE SEAT STORAGE

• To open the storage compartment under the seat, insert the key into the lock, turn it clockwise and, holding it in this position, raise the seat.
• ADVICE
  • Try to lift the seat slightly to make sure the storage is properly closed.

To close the storage, lower the seat and press down firmly. Make sure that the storage is properly closed.

• WARNING !
  Be careful not to trap your hands or other body parts when closing the back cover.

• ATTENTION
  In cold and humid climates, due to frost, locks and door mechanisms may not work properly.

• ATTENTION
  Make sure the tailgate is closed before riding. If the rear cover is not closed, the hinges may be damaged. Make sure nothing is near the tailgate lock and hook when closing as this may damage the latch.

REAR STORAGE

• To open the rear storage, insert the key into the lock, turn it clockwise and lift the top cover.
• To close the rear storage, lower the top cover, insert the key into the lock and turn it clockwise while pressing down on the top cover. By turning the key counterclockwise, the compartment will be locked.

USB PORT
The electric mobility scooter is equipped with a USB port. It allows you to charge your device. When the switch is in the I position, the USB port allows charging. When the switch is in the O position, the socket is inactive and the mobile device will not be charged.

• ATTENTION
  The USB port will only be active when the vehicle is turned on.

• WARNING !
  Make sure that the USB port cover is always tightly closed when not in use.

FOLDING FOR STORAGE OR TRANSPORT
The scooter is not foldable for storage or transport.

TRANSPORT OF THE MOBILITY SCOOTER

• Transport of the scooter should be done with a vehicle equipped with a loading ramp with a load capacity equal to or greater than the full weight of the scooter (scooter + user). In the case of the Draco model, the loading ramp must have a load capacity of 263 kg.
• The dimensions of the loading space must be increased by 10 cm to the dimensions of the scooter.
• The user may not sit on the scooter during transport.
• The scooter must be tied down.

ATTENTION
The scooter is not intended as a seat for vehicle travel.

WEIGHTS OF REMOVABLE PARTS

• Lithium-ion battery – 10 kg
• Lead-acid battery – 24,8 kg (4 x 6,2 kg)
• Rearview mirrors – 0,200 kg

LOCATION OF POINTS FOR ADDITIONAL LOADS

A little extra weight can be hung on the hook under the handlebars. The maximum lifting capacity of the hook is 25 kg, exceeding this weight may cause the hook to break off.

LONGER BREAKS IN USING THE VEHICLE AND RE-PREPARING FOR DRIVING
In the event of a planned longer break in the use of the vehicle:

1. Place the scooter on level ground.
2. Make sure all brakes are released (do not use the parking brake).
3. Check the pressure in the tyres (low pressure increases the risk of deformation of the tyre).
4. Switch off the power with the main switch, the scooter components (even when not in use) use a minimum amount of energy. Failure to turn off the main switch will discharge the battery, and consequently its sulphation and irreparable damage.
5. We recommend covering the mobility scooter with a cover, tarpaulin or blanket.

To prepare the vehicle for the next drive:

1. Check tyre pressure.
2. Check the brake fluid level (DOT 4).
3. Charge the battery (full cycle, approx. 8 hours).
4. Check the operation of lights and horn.
5.  Adjust the mirrors
6. Carry out a test drive in first gear, and during it check the operation of the brakes and steering.
7. If the road test in first gear was without problems, carry out the test run through the full speed range.

MOVING OR RELOCATING OF THE MOBILITY SCOOTER
To move the scooter when not in use, make sure that the power to the scooter is completely turned off using the main switch under the scooter seat, unlock the steering wheel and parking brake and move the scooter by grasping it with both hands on the steering levers.

• WARNING !
  Make sure not to pinch your fingers or clothing when lowering the armrests, moving the backrest, opening and closing the compartments. Under no circumstances should you perform these activities  while driving.

• WARNING !
  The scooter may interfere with devices that emit electromagnetic fields in its vicinity, e.g. alarm systems, automatic doors, etc.

• WARNING !
  The performance of the scooter may be influenced by electromagnetic fields, e.g. from cell phones, electric generators, high power sources.

• WARNING !
  The braking distance on slopes can be significantly longer than on a flat road.

• WARNING !
  The temperatures of some surfaces of the scooter may rise when exposed to heat sources, e.g. sun rays.

• IGNITION RESISTANCE LEVEL OF MATERIALS AND MODULES
  The product is classified as flame-retardant in accordance with the requirements of PN-EN 1021-2: 2014.

• BATTERY RECYCLING
  The used battery should be taken to a specialized disposal point.

• SAFETY AND PRODUCT RECALL
  Up-to-date information related to the safety of our products is available at your point of sale.
  EXPECTED PRODUCT LIFESPAN
  The scooter has no expiry date for safe use. Its life cycle is limited by mechanical wear and tear and degradation of the batteries, which can be replaced with new ones at an authorized service point. In the case of proper service, the manufacturer estimates the product’s lifetime as 10 years.

SERVICE MANUAL

• MAINTENANCE AND SERVICE INSTRUCTION
  In order to maintain the efficiency of the vehicle, it is the user’s responsibility to check the condition of some parts of the scooter and their possible maintenance (we recommend checking the condition of the vehicle before and after each use). The elements for which the user is responsible are:

  • Battery condition control – charge the scooter with a full cycle, then start it and check the charge level on the display (see chapter SPEEDOMETER). If the battery voltage is above 49 V, the battery is considered functional, but over time the range of the scooter may be lower than specified in the specification, despite the correct voltage. In case that the voltage of a fully charged battery is below 48 V, the battery must be replaced with a new one. Failure to check the battery condition or driving on a faulty battery may cause the scooter to switch off unexpectedly during the journey. In case of a replacement, spare parts can be purchased directly on the manufacturer’s website shop.veleco.eu by searching under the following product code:

  • DRABALITX – lithium-ion battery. Tool-free plug & play replacement by user.

  • AKUAGM12SET4 – lead acid battery. Appropriate tools and knowledge are required for replacement, the replacement must be performed by a person with appropriate qualifications.
    ATTENTION
    The batteries listed above are not interchangeable! The lithium-ion battery will not work in the scooter that originally had a lead-acid battery installed and vice versa.

  • The braking system control

  • while standing next to the scooter, press the brake lever. The lever should have a noticeable resistance. With the lever pressed down, try to push the scooter, if the brakes are working properly the scooter will not start. Release the brake lever, fully working brakes should return to the starting position. If the rear brake lever (left lever) is too tight, or if it does not block the scooter, it may be necessary to adjust the brake. The adjustment is made without tools by screwing in (loosening) or unscrewing (tightening) the barrel screw, which deter-mines the initial tension of the brake cable. If the adjustment range is exhausted and the brake still does not perform as expected, it may be necessary to replace the brake pads. In this case, we recommend that you use the manufacturer’s official website. The front brake (right lever) is a hydraulic brake, so it has no adjustment range, and its malfunction should be reported directly to the service department. If the brakes work properly, it is recommended to additionally check the operation of the parking brake. Once locked in accordance with the instructions in the PAR-

• KING section, the scooter should not be pushed, otherwise the brake cable must be tightened in accordance with the instructions for adjusting the rear brake above. If the regulations described above do not allow the brakes to be adjusted properly, contact the seller or the manufacturer. In case of replacement, spare parts can be purchased directly on the manufacturer’s website, shop.veleco.eu, by searching under the following product code:

  • DRAHEL – electromagnetic brake
  • DRALHP – front brake cable
  • DRAUPH – front brake handle
  • DRAHBP – front drum brake
  • DRALHT – rear brake cable
  • UNISZCZHAM – universal brake shoes

• Tyres control – check the visual condition of the tyres, examine them and check them for any mechanical damage or cracks. If the tyres are visually in a good condition, check their pressure. If the tyre pressure is incorrect, see section INSTRUCTION ON HOW TO INFLATE TYRES. After inflating the tyres, wait about 10 minutes to check that the pressure in the tyres does not drop. If the tyres have visual damage, they should be replaced when the pressure decreases, despite the good condition of the tyres, it is possible to damage the inflation valve or a possibility of a microscopic hole in the tyre. Tyres can be vulcanized with repair kits available on the market or in specialist workshops. If replacement is necessary, spare parts can be purchased directly on the manufacturer’s website, shop.veleco.eu, by searching under the following product code:

  • UNIO3-0-10 – front and rear tyre
  • UNIWENZ – universal valve

• Lighting control – use the appropriate buttons on the shift lever to check that the correct lights come on. In the event of failure of a light, the appropriate bulb may need to be replaced. If replacing the bulb does not help, the controller or the converter may be damaged. In this case, please contact the manufacturer’s official service directly. If it is necessary to replace, spare parts can be purchased directly on the manufacturer’s website, shop.veleco.eu, by searching under the following product code:

  • FASLAMP – front lamp
  • FASLTS – central rear lamp
  • UNIZARX – bulb 12 V universal 21/5
  • UNIZARLEDLB – LED bulb universal full 21/5 (A’2)
  • UNIZARDK – indicator bulb
  • DRAST48 – controller 48 V
  • ZT15PRZ48V – universal 48 V converter

• Sound system control – using the appropriate buttons check that the scooter emits a warning sound. If the signal does not work, it may be necessary to replace the horn. If replacing the horn does not help, damage to the controller or converter is possible. In this case, please contact the manufacturer’s official service directly. If it is necessary to replace, spare parts can be purchased directly on the manufacturer’s website, shop.veleco.eu, by searching under the following product code:

  • UNIWKLAKSX – universal horn

• Keeping the vehicle clean – remove dirt or snow from under the rear part of the chassis, refer to Cleaning Methods to Avoid Corrosion in the SPECIFICATIONS section.

• Failure to pay attention to the condition of these components may result in impaired vehicle functionality and may lead to serious damage.

• Spare parts can be purchased at the manufacturer’s official online store: shop.veleco.eu. Each part has its individual number that can be searched for (SKU). This number is visible on the packaging as well as in the online store. The list of all components of the DRACO mobility scooter can be found at shop.veleco.eu/?filter_model=turris with a list of prices and the possibility of ordering them.

• Tools and equipment needed to repair and maintain the vehicle:

  • basic mechanical and electromechanical tools.

INSTRUCTIONS ON HOW TO PERFORM A PARAMETER CHECK

• The damage for which the user is responsible includes any mechanical damage that may have occurred during operation, e.g. as a result of an impact or neglect of servicing.
• Failure to pay attention to maintenance or inspections may cause danger on the road, cause an accident, endanger the user’s health and life, and void the warranty. Service operations must be  performed by an official service technician. The service of an official servicer is not required to replace the consumable parts of the vehicle, such as light bulbs and brake pads.
• In order to maintain the warranty and service, the user is obliged to perform periodic service inspections by the manufacturer’s official service.

REGISTER OF PERIODIC INSPECTIONS

• name and surname
• VIN number
• date
• date of sale

During the one-year warranty period, inspections should take place every 3 months from the date of purchase, and then every 6 months.

MOBILITY SCOOTER REPAIR

• Any repairs of the mobility scooter should be performed by an authorized Veleco service technician, or if this is impossible – by a qualified person.

• User-replaceable parts include a lithium-ion battery and mirrors. Available for purchase in the manufacturer’s official online store at shop.veleco.eu.
  Instructions for disassembling the mirrors and the lithium-ion battery (see chapters DISASSEMBLY OF SCOOTER PARTS, DISASSEMBLY OF THE BATTERIES and DISASSEMBLY OF THE rearview

• MIRRORS).

• All parts, except mirrors and lithium-ion batteries, should be replaced / repaired by an authorized Veleco service technician or after prior arrangement with the company’s representative, by a qualified person.

• A list of authorized service facilities can be found at veleco.eu/distributors.

• Pursuant to Directive 2009/125 / EC of the European Parliament, the manufacturer guarantees a 2-year full availability of spare parts and a 10-year period of storage of technical documentation.

• In the case of warranty transport to an authorized service point, the packing and transport procedure is determined by the manufacturer’s representative.

PROBLEM SOLVING

• WARNING !
• Self-diagnosis and troubleshooting with the procedures outlined below may damage your mobility scooter instead of troubleshooting. Such damage will not be covered by the warranty. In case of any doubts as to the procedure or recognition of a defect, immediately contact an authorized service center or dealer.

• Ignition key is not turned properly. The battery is incorrectly connected or disconnected.
• Control module damaged. Damage to the junction box. Damaged cable harness.

The motor is running, the scooter does not start, insufficient battery charge.| Broken / loose directional lever potentiometer. Damaged motor. Damage to the junction box.
The scooter is on but not accelerating.| Low battery level. The parking brake is on.
The scooter is on but accelerating very slowly.| Low battery level.
The battery level does not increase during charging.|

• Batteries are not properly matched. The main switch is in the off position. The charging socket is broken.
• Incorrect charger. The charger is damaged. The socket is damaged. The battery has lost voltage due to self-discharge.
• The EU / UK plug adapter is damaged.

The wheels make a squeaking noise.| Stuck brake pads after being stored in a humid atmosphere. They will improve with continued use.

TECHNICAL SPECIFICATION

OVERVIEW

• Max user weight: 160 kg / 25.2 st
• Scooter weight: 103 kg / 16.2 st (w/ Lead-Acid Gel battery), 88 kg / 13.9 st (w/ Lithium-Ion battery)
• Hill climbing ability: 17°
• Maximum range on single charge: 45-50 km / 28-31.1 mi
• Speed of response : Low
• Maximum speed : 8 mph / 12 km/h
• Acceleration system: Push of a button
• Seat adjustment: Yes
• Suspension: Full
• Compliant with DVLA requirements : Yes
• Scooter class: Class-3
• Vehicle autonomy : Level 0
• Optimal air humidity for storage and use : 30%
• Working temperature of electronic parts : -10 °C to +40 °C
• Turning radius: 165 cm / 65”

MOTOR

• Power: 800 W
• Voltage: 48 V

BATTERY

• Type: SLA – lead acid or LIT-ION – lithium-ion
• Capacity: 20 Ah
• Voltage: 48 V
• Life cycle: 600 full charges
• Charge time: ≈8 h

DIMENSIONS

• Seat dimensions: 410 × 470 mm
• Scooter dimension s: 1520 × 670 × 1020 mm

BRAKES

• Front: Drum
• Rear: Drum
• Magnetic brake: Yes

WHEELS

• Amount: 3
• Type of tyres: Pneumatic tubeless
• Size: 3.00-10”
• Tyre pressure : 2.25 bar / 225 kPa /
• 32.5 PSI

LIGHTS

• Low beam headlight: LED (integrated with lamp) High beam headlight: LED (integrated with lamp) Tail lights: LED (integrated with lamp)
• Daytime running lights: LED (integrated with lamp) Signal lights: LED (integrated with lamp)
• Brake light: LED (integrated with lamp)
• Hazard lights : LED (integrated with lamp)

FEATURES

• Horn
• Rearview mirrors
• Steering wheel lock
• Parking brake
• Electric LED display
• USB Port
• Alarm
• Remote control
• Comfortable seat

The manufacturer reserves the right to introduce changes to the technical parameters. Measurement tolerance ± 15 mm / 1.5 kg / °.
The theoretical range value will be reduced if the vehicle is used frequently on slopes, rough terrain or taking curbs.
The above technical parameters apply to the mobility scooter in a standard configuration and under optimal environmental conditions.
If other accessories are used, the values in the tables will change. Changes in outdoor temperature, humidity, ground slope, and battery level can reduce performance.

INSTRUCTION ON HOW TO INFLATE TYRES

1. Make a visual inspection of the tyre – if it is not cracked, damaged, and whether there are any foreign bodies (nails, pins, screws, glass pieces).
2. Adjust the wheel so that it is easy to fit the inflating attachment.
3.  Unscrew the valve cover.
4. Attach the end of the pumping device to the valve.
5. Inflate the wheel to the required pressure (optimal is 2.25 bar).
6. Remove the end of the tyre inflator from the valve.
7. Make sure the valve is tight (e.g. using soapy water).
8. Reattach and tighten the valve cover.

DISASSEMBLY OF SCOOTER PARTS

disassembled by trained personnel! Take hold of the base at the side edges.
LITHIUM-ION BATTERY|

• Use the handle intended for this to be lifted.
• ATTENTION
  The weight of the battery is 10 kg, be careful when removing it .

DISASSEMBLY OF THE BATTERIES

LEAD-ACID BATTERY

The lead-acid battery cannot be disassembled by yourself.
LITHIUM-ION BATTERY
To disassemble the lithium-ion battery it is necessary to:

1. Open the storage compartment under the seat (see section UNDER THE SEAT STORAGE).
2.  Disconnect the plug shown in the photo above.
3.  Pull the battery out by the handle.

INSTRUCTIONS FOR SWITCHING THE ELECTROMAGNETIC BRAKE ON AND OFF

• The scooter is equipped with an electromagnetic brake located at the rear of the vehicle on the wheel axle. The lever in the upper position disengages the brake, while the lever in the lower position reactivates it. The electromagnetic brake is activated by default.
• OPERATION OF THE ELECTROMAGNETIC BRAKE
• If the accelerator lever is released, the vehicle will automatically brake. This prevents the vehicle from rolling downhill.

DISASSEMBLY OF THE REARVIEW MIRRORS

1. Lift up the cover on the fixing screw.
2. Then unscrew the screw with a 14 mm wrench.
3. Loosening can be carried out by hand when the screw is sufficiently loose.

CLEANING AND CARE

The vehicle should be inspected periodically, especially at the first inspection within three months of purchase. Failure to perform periodic inspections may void your warranty as it is subject to misuse.
After riding in the rain, wipe the vehicle with a soft cloth and allow it to dry completely before riding again.
When cleaning the vehicle, avoid high-pressure washing, especially around the battery compartment. Do not flush the rear inner fenders where the charger, controller and other parts are installed. If the charging port on the scooter is wet, do not charge until it is dry.
Do not use harsh chemicals to clean the vehicle.
Cleaning the pillows:

• Clean the seat and backrest with a cloth dampened with hot water, but do not get wet.
• Use a mild, commercially available detergent to remove dirt.
• Stains can be removed with a sponge.
• Do not use strong cleaning fluids such as solvents.
• Never clean with steam and / or pressure cleaning equipment.

Cleaning electronic parts:

• Wipe the control unit with a cloth dampened with a few drops of a commercial household cleaner.
• Do not use abrasive or sharp tools for cleaning, such as a wire brush or metal brush, as they may scratch the surface of the control unit.
• Be careful not to wet the electronic components with water.

WARRANTY STATEMENT

VELECO’S ONE-YEAR LIMITED WARRANTY
For Veleco Brand Products

• WARRANTY STATEMENT
• The One-Year limited warranty issued by Veleco sp. z o.o. with its registered office in Poland, Czestochowa 42-202, ul. Bernarda Ludwika Hantkego 7, registered in the National Court Register under the entry No. KRS: 0000878290, NIP No. [Tax Identification Number]: 573-292-38-76, REGON No. [statistical number]: 387919068 (“Veleco” or “Warrantor”) provides additional rights separate to the rights provided by Consumer Law in the country of the purchase including but not limited to those relating to non-conforming goods. As such, this warranty is a voluntary manufacturer’s warranty providing additional benefits, and in no way restricts application of Polish Consumer Law stated on day 30 may 2014 yr. and act from day 23 april 1964 yr. Civil Code („consumer law”).
• Any Customer (“Warrantee”) that has purchased Goods (“Products”) directly from Veleco can choose whether to claim warranty service under Veleco One-Year Limited Warranty or under Polish
• Consumer Law which is the country of the purchase.
• Veleco will not be held liable to perform any warranty service requests issued by members of Veleco Authorized Reseller Network or their Customers under any additional warranty terms outside of
• Veleco’s One-Year Limited Warranty or any Consumer Law of the country of product purchase.
• If a product was purchased from a member of Veleco Authorized Reseller Network, Consumers have the right to claim service request directly from Retail Seller under Veleco One-Year Limited
• Warranty, additional warranty terms provided by a member of Veleco Authorized Reseller Network or under Consumer Law of the country of the purchase.
• Important: The Veleco’s One-Year Limited Warranty terms and conditions shall not apply to consumer law claims.

STATEMENT AND ASSURANCE OF THE WARRANTOR

• The Warrantor hereby declares and warrantees to the Holder of the Warranty that
  the Products were produced correctly, in accordance with the Agreement and technical specification, and in accordance with the Warrantor’s best knowledge and currently applicable rules of technical knowledge, construction art and applicable law. Through this Warranty, the Warrantor assumes liability for defects in the Product resulting from a gross violation by the Warrantor of any of the  Warrantor’s obligations..

THE LIABILITY OF THE WARRANTOR RESULTING FROM THE WARRANTY

• The Warrantor shall be liable to the Holder of the Warranty for any defects of the Goods that will come to light after the date of the sale of the Products by the Customer (by the Eligible Person) – until the expiry period resulting from this warranty stated in point III of Warranty statement section and provided correct and intended use.

THE TERM OF THE WARRANTY

• The liability of the Warrantor under this Warranty begins on the day of the finalization of the transaction of the Products (delivery accepted by customer) and ends after in case of: (i) vehicle – 12 months, (ii) battery – 6 months.

LIMITATION OF LIABILITY

• Other than the consumer law rights to which the Holder of this Warranty is entitled as set out at the beginning of this document, all warranties, conditions and other terms not included in this warranty are excluded from Veleco’s One-Year Limited Warranty. Veleco does not claim liability for any promises, conditions or warranties about service other than stated in this warranty document.
• Veleco does not claim responsibility for damage which is not a direct result of Veleco’s actions. This includes responsibility for loss of quality, benefits or profits that were a direct result of a member of
• Authorized Reseller Network actions. These exclusions shall not apply to (i) death or personal injury, (ii) fraud or gross negligence; or (iii) fraudulent misrepresentation; or (iv) any other liability that can not be limited or excluded as a matter of law.

WHAT DOES THIS WARRANTY COVER

• The Warranty covers only Veleco-branded products and accessories that were distributed with defects resulting from the inadequate quality of the material, improper production technology, improper assembly contrary to what the manufacturer warranted in Veleco’s user manuals, technical specifications and other Veleco Product published guidelines for a period of one year from the date of original retail purchase by the end-user.
• In the event of any defect in materials and workmanship, you will be able to direct your claims to Veleco even in situations where you purchased the Veleco Product from a third party.
• Important: All claims made under the Veleco One-Year Limited Warranty will be governed by the terms set out in this warranty document.

WHAT DOES THIS WARRANTY NOT COVER

• The warranty does not apply to any non-Veleco Brand Products, even if packaged or sold with them. Non-Veleco Brand Products may be an additional benefit provided by a member of the Authorized
• Reseller Network and as such are a subject of additional terms and conditions provided by third-party Retail Sellers.
• This warranty does not cover: (a) damage caused by the Customer, third party or force majeure; (b) damage caused by unauthorized modifications and / or replacement of parts outside of the Veleco authorization; (c) cosmetic damage, including but not limited to scratches, broken plastic, dents that occured during usage; (d) damage caused by improper operation of the Product outside of the provided user manual or any other Veleco published guidelines; (e) defects caused by normal wear and tear or otherwise due to aging and usage of consumable parts, that has not occurred due to defect in materials or workmanship. This includes: damage or wear to tyres, damage to brakes, damage to brake pads, damage to rims, damage to battery, tearing or wiping of the seat cover, damage to shock absorbers, breach of the frame geometry, motor damage due to lack of oil caused by the fault of the user, damage to battery caused by irregular or lack of recharge, mechanical and thermal damages and defects caused by them; (f) damage caused by use with a third party components of products outside of Veleco Product specifications; (g) damage caused by accident, abuse, misuse, fire, earthquake or other external cause; (h) damage caused by service (including upgrades and expansions) which were not performed by Veleco or authorized representative of Veleco; (i) damage resulting from negligence and lack of periodic inspection checks.

HOLDER OF WARRANTY RESPONSIBILITIES

• The Warrantee is responsible for proper maintenance, storage and usage of the Products. As such, the Warrantor is released from liability if the Warrantee does not perform periodic inspections which should be performed at the latest by 3/6/9/12/18 months from the date of the purchase.

VELECO PROCEDURES IN THE EVENT OF WARRANTY CLAIM

• If a service claim is submitted to Veleco during period of the Warranty, Veleco will, at its option:
• Repair the Veleco Product, using new parts that are equivalent in performance and reliability, or
• Replace the Veleco Product with the same model (or with Warrantee consent a product of similar functionality), equivalent in performance and reliability, or
• Issue refund in exchange for the return of Warrantee Veleco Product.

Any replacement item (product or part) or issued refund becomes the property of the Warrantee, while the replaced item (product or part) becomes property of Veleco.
Any replaced part or product assumes the remaining warranty of the original Product or a separate warranty of ninety days from the date of replacement/repair.
Veleco reserves the right to repair or replace products and parts with comparable products and parts that comply with local standards.
COMPLAINT PROCEDURE

1. The Warrantee is obliged to notify the Warrantor about any noticed defects of the Product, which became apparent after the sale of the Product within 3 working days from the day of the notice. The  documents allowing the beginning of the complaint procedure are original proof of the purchase and the correctly completed warranty card.
2. All claims under the Warranty should be submitted to the place where the vehicle was purchased in the written form and contain a list of perceived defects associated with the Product.
3. Consideration of the complaint will take place within 14 business days of reporting the defects in the service, while the repair will be performed within the time agreed with the Customer.
4. Issues not included in this card are regulated by the relevant provisions of the Civil Code.

WARRANTY SERVICE OPTIONS
Veleco will provide warranty service through one of the following options:

• Home-call servicing. Official Veleco service cars and engineers might visit the Customer at the agreed location and within agreed time-frame.
• Collection servicing. If Veleco determines the Warranty issue exceeds the extent of repairs /replacements a Home-call servicing can provide, Veleco will take the Product to its official warehouse for a period of time necessary for repairs.
• Do-it-yourself (“DIY”) servicing. Under DIY servicing, Veleco will provide the Customer with replacement parts as well as instructions how to perform the servicing. Customers are then requested to  make repairs in the authorized local vehicle workshop, with an invoice to Veleco name. Veleco will then reimburse the cost the customer had to pay for the necessary repairs.

END STATEMENT
No member of Veleco Authorized Reseller Network, agent or employee is authorized to make any alterations to this warranty. If any term is held to be illegal or unenforceable by the force of law, it will be excluded from the warranty and the legality of the enforceability of the remaining terms shall not be affected.
© 2023 Veleco sp. z o.o. All rights reserved.
MANUFACTURER’S NAME AND REGISTRATION ADDRESS

VELECO sp. z o. o.

MATERIAL DEGRADATION
Do not use the scooter with visible damage to mechanical or electrical parts, in particular the drive components, brakes, suspension, power supply and control system.
ACTIONS IN THE EVENT OF MALFUNCTION OF THE PRODUCT
Do not use the scooter with visible damage to mechanical or electrical parts, in particular the drive components, brakes, suspension, power supply and control system.
In the event of any irregularities in the operation of the drive, braking or steering system, stop driving as soon as possible.
If any faults in the signalling systems (lights, sound signals) are found, these faults should be removed as soon as possible, however, further driving is possible provided that special care is taken.
In the event of minor damage to protective and decorative elements (fenders, boot covers, mouldings and protective panels), the operation may be continued at your own risk (e.g. in the event of damage to the front cover, the manufacturer is not responsible for any damage to the electrical system caused by moisture).

PRECAUTIONS

• Do not use the scooter near power plants, transformer stations, and in hospitals near magnetic resonance imaging equipment and the like (ECG, EEG, etc.).

• Avoid using your scooter during an electrical storm.

• Atmospheric pressure has no effect on the use of the vehicle.

• The optimal air humidity for use and storage is 30%.

• We do not recommend using the scooter at temperatures below 5 ° C, as the scope of the operation will significantly decrease at such temperatures.

• Remember to properly prepare for driving in very high temperatures. Some parts of the scooter can become hot under the sun’s rays, which can cause burns.

• The scooter should not be used during heavy snowfall or heavy rainfall.

• In strong winds, bear in mind that a gust of wind can push the scooter to the side.

• ATTENTION
  If you have any doubts as to whether your disability precludes the safe use of the scooter, consult a doctor.

• ATTENTION
  Any serious incident related to the device must be reported to the manufacturer and to the competent authority of the Member State in which the user or patient resides.

• ATTENTION
  The scooter contains programmable electronic systems that only the component manufacturer has access to at the production stage of the above-mentioned systems.

• SYMBOL LIST

COPYRIGHT NOTICE
The material in this document is the intellectual property of Veleco sp. z o.o. No part of this document may be reproduced or used in any way without the written consent of the copyright holder, except for the use of quotes in the review. We make every effort to prepare this document, but we do not guarantee the correctness of its content. Our products are constantly being improved and we reserve the right to make changes to their specifications without prior notice.

TRADEMARK

• Veleco TURRIS® is a registered trademark of Veleco sp. z o.o.

CHANGE HISTORY
v1.0 (2.01.2023)

TECHNICAL SUPPORT

• If you encounter a problem with the product and the solution cannot be found in this manual, please contact the place of purchase or local distributor. Alternatively, please seek help by:
• Visiting our main website: veleco.eu
• Contact with our website by e-mail: serwis@veleco.pl
• VELECO
• +48 34 350 80 44
• info@veleco.pl
• www.veleco.eu
• Czestochowa, Poland

References

• Our offer - Veleco B2C
• Our offer - Veleco B2C
• Distributors - Veleco
• Veleco Luxury Electric Scooters - Manufacturing people’s freedom

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>