ideal lux SP10-INS Pasha Pendant Light Instruction Manual

May 15, 2024
ideal lux

ideal lux SP10-INS Pasha Pendant Light Instruction Manual

THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

    1. Installation Instructions
  1. Installation Instructions

  2. Installation Instructions

    1. Installation Instructions
  3. Installation Instructions

    1. Installation Instructions

SAFETY INSTRUCTION

  1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598-

  2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.

  3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.

  4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.

  5. Always isolate power before commencing installation, maintenance or repair.

  6. The luminaire contains certain parts which can be very hot.

  7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.

  8. Always tighten the screws firmly to avoid contact problems.

  9. This fitting should only be installed indoors.

  10. Luminaires not suitable for recessed on normally flammable surfaces.

  11. Luminaire not suitable for direct mounting on normal flammable surfaces.

  12. This fitting is only suitable for fixing to the ceiling.
    Installation

  13. This fitting is only suitable for fixing to the wall.
    Installation

  14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
    Installation

  15. Only use lamps which do not exceed the maximum specified wattage
    Installation

  16. Always observe the minimum distarice between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
    Installation

  17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
    Installation

  18. Cracked or broken safety glass has to be replaced immediately. Use only manulcturer approved parts complying with regulations.
    Installation

  19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.

  20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
    Installation

  21. Class | Electrical safety guaranteed by the main insulation and an additional protective conduc- for (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
    Installation

  22. Class II Bectrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.

  23.  Class III Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing Excluded.

  24.  Not protected.

  25. Protected against solid objects greater than 50 mm.

  26. Protected against solid objects greater than 12 mm.

  27. Protected against solid objects greater than 2,5 mm.

  28. Protected against solid objects greater than 1mm.

  29. Dust protected.
    Installation

  30. Totally protected against dust infiltration.
    Installation

  31. Not protected.

  32. Protected against vertically falling water drops.

  33. Protected against water drops falling with a maximum angle of 15″ to the vertical axis.

  34. Protected against rain.

  35. Protected against splashing water.

  36. Protected against water jets”

  37. Protected against strong water jets.

  38. Protected against temporary immersion.”

  39. Protected against prolonged immersion.

  40. Luminaire not suitable for covering with thermally insulating material
    Installation

  41. Caution, risk of electric shock.

  42.  Do not stare at the operating light source.
    Installation

Suspension lamp

E14 max 10 x 40W / 220~240V 50/60Hz

  • 8021696082196 CROMO
  • 8021696082257 ORO

Icons

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals