casa systems 5G2105-48 Enterprise Small Cell User Guide
- May 15, 2024
- casa systems
Table of Contents
casa systems 5G2105-48 Enterprise Small Cell
Product Information
- Specifications
- Brand: Festo
- Model: G2105-48
- Compliance: FCC Part 15, California Prop65
- Power Source: Power adapter (supplied)
- GPS: Indoor GPS antenna
- Network Connectivity: Ethernet
Product Usage Instructions
- Cautions and Warnings
- Warning: Read and understand the installation instructions and all safety warnings before connecting the eFemto to the power source. Failure to understand safety precautions may result in injury.
- Warning: Operate the event only with the power adapter supplied with the product.
- Warning: Do not cover the event or block the airflow to the device with any objects.
- California Prop65 Warning: The plastic and cords on this product contain phthalates, a chemical known to the State of California to cause cancer, birth defects, and other reproductive harm. Wash hands after handling.
- Prerequisites
- Identify a location for the event, central to users, but no more than 21 feet from an exterior window or wall to allow for a strong GPS signal.
- Identify a power source for the eFemto.
- Follow device mounting, installation, and power-up steps.
- Mounting Procedure
- Determine the mounting location and verify that no wires, pipes, etc., are directly behind or in the wall at the point of mounting.
- Use the wall mounting bracket to act as a template to mark anchor holes on the wall.
- Drill holes into the drywall and push in the supplied plastic drywall anchors. Installation on surfaces other than drywall may require different anchoring hardware.
- Align the mounting bracket with the wall anchors and attach using the supplied screws.
- Slide the event with the mounting bracket into the wall mounting bracket.
- Fasten retaining screws on the side of the bracket.
- Ensure power supplied through the PoE port meets Class 4 and Class 5 requirements.
- GPS Installation
- Connect the GPS antenna cable (indoor use only) to the GPS port of the event.
- Note: The GPS antenna must stay connected to the event at all times for operation. The initial GPS fix can take up to 60 minutes.
- Ethernet and Power Connections
- Attach the supplied Ethernet cable from your router or modem LAN port to the event WAN/PoE port for network connectivity.
- Optional Accessories Available
- A full list of optional accessories can be viewed and ordered from www.verizonwireless.com.
FAQs
- Q: Can I use a different power adapter for the event?
- A: It is recommended to operate the event only with the power adapter supplied with the product to ensure proper functionality and safety.
- Q: How long does it take for the GPS to initially fix?
- A: The initial GPS fix can take up to 60 minutes. Ensure that the GPS antenna stays connected at all times for optimal operation.
Cautions and Warnings
- Warning: Read and understand the installation instructions and all safety warnings before connecting the eFemto to the power source. Failure to understand safety precautions may result in injury.
- Warning: Operate the event only with the power adapter supplied with the product.
- Warning: Do not cover the event or block the airflow to the device with any objects.
- California Prop65 Warning: The plastic and cords on this product contain phthalates, a chemical known to the State of California to cause cancer, birth defects and other reproductive harm. Wash hands after handling. For more information, please visit the following site: www.p65warnings.ca.gov.
FCC
USA: Federal Communications Commission (FCC) statement This device
complies with FCC part 15 FCC Rules.
Operation is subject to the following two conditions:
- This device may not cause harmful interference and
- . This device must accept any interference, including interference that may cause undesired operation of the device.
FCC Warning:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, under part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used per the instructions,
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC requirements for RF exposure in public or
uncontrolled environments. The device should be installed and operated with a
minimum distance of 57cm between the radiator and your body.
FCC ID: 2AO385G2105-48
What’s in the event Box
- 5G Enterprise Small Cell (eFemto)
- Mounting Bracket with Hardware
- GPS Antenna and cable (7m)
- Ethernet cable – 2m
- Power cord
- Power supply (not plenum rated)
- Quick Start Guide
Port Connections
Antenna Connections
Prerequisites
- Ethernet and Backhaul (B/H) Requirements For optimum performance regarding backhaul bandwidth requirements and specific firewall settings, please refer to the User Guide.
GPS Signal
- The event requires a strong GPS signal from the provided indoor GPS antenna. For installation other than with the provided GPS antenna, please refer to the online 4G LTE Network Extender for Enterprise User Guide.
Placement
The eFemto can be installed: vertically or horizontally on a wall, floor, or ceiling. Place the unit at least 10 feet away from products that generate electromagnetic radiation (e.g., microwave oven).
- Identify a location for the event, central to users, but no more than 21 feet from an exterior window or wall to allow for a strong GPS signal.
- Identify a power source for the eFemto.
- Follow device mounting, installation, and power-up steps.
Mounting Procedure
The package contains screws and anchors for drywall mounting. Installation on alternate surfaces will require the purchase of the appropriate anchors and hardware.
- Determine the mounting location and verify that no wires, pipes, etc., are directly behind or in the wall at the point of mounting.
- Use the wall mounting bracket to act as a template to mark anchor holes on the wall.
- Drill holes into the drywall and push in the supplied plastic drywall anchors. Installation on surfaces other than drywall may require different anchoring hardware which can be purchased at your local hardware store.
- Align the mounting bracket with the wall anchors and attach using the supplied screws (4 x No. 10 1” length with fastener).
- Slide the event with the mounting bracket into the wall mounting bracket.
- Fasten retaining screws (Self-tapped screw, 1018 harden, PA4*25, Phillips 2#, Color-Zn plating) on the side of the bracket.
- When power is supplied through the PoE port, the PoE power source should meet Class 4 and Class 5 requirements.
Installation
GPS Installation
Connect the GPS antenna cable (indoor use only) to the GPS port of the event.
Note: The GPS antenna must stay connected to the event at all times for
operation. The initial GPS fix can take up to 60 minutes.
Ethernet and Power Connections
Attach the supplied Ethernet cable from your router or modem LAN port to the
event WAN/PoE port for network connectivity.
Plug in the Power Supply and insert the power cable into the eFemto Power port. Automatic startup and hardware initialization will begin.
POWER ON
At startup, the event will conduct self-configuration. This will take between
30 – 60 minutes the first time the event turns on.
Optional Accessories
Optional Accessories Available
- Power over Ethernet (POE) Device
- A full list of optional accessories can be viewed and ordered from www.verizonwireless.com.
Automated Startup
The following Status LED sequence will occur. Upon successful setup, the LED
will blink green.
Note: If the LED fails to turn green after one hour or is blinking a series of red pulses, consult the troubleshooting section (below).
Troubleshooting
- No GPS Signal
- The Sync LED is off and the Alarm LED fixed red indicates no GPS signal. Check the About eFemto page in the Advanced Settings web interface, on the tabs for “Status and Alerts” or “GPS” to see the status of the GPS constellation.
- Is my wireless device connected to the event?
- Using the Advanced Settings web interface, sign in and the Connected Devices panel for indication of connected users.
- Cannot reach eFemto GUI or locked out of the device.
- Press the RESET button for 10 seconds to reset the system to factory default settings.
- 5G Enterprise Small Cell (for indoor use only) Installation Reference Guide
Copyright 2024 Casa Systems. All rights reserved. Doc-3720 Rev 6.0
References
- p65warnings.ca.gov
- p65warnings.ca.gov/
- Verizon: Wireless, Internet, TV and Phone Services | Official Site
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>