Comfee CVG36W9AST Curved Glass Range Hood 36 Inch User Manual

Comfee CVG36W9AST Curved Glass Range Hood 36 Inch

INTENDED FOR RESIDENTIAL COOKING USE ONLY

WARNING
alerts you to situations that may cause serious bodily harm, death or property damage.

CAUTION
indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury.

IMPORTANT
indicates installation, operation, maintenance or valuable information that is not hazard-related.

WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty.
2. Before servicing or cleaning the unit, unplug and switch the power off at the service panel and lock service disconnecting means to prevent power from being switched on accidentally.
3. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
4. Installation work and electrical wiring must be done by qualified personnel by all applicable codes and standards, including fire-rated construction codes and standards.
5. Sufficient air is needed for proper combustion and exhaustion of gases through the flue (chimney) of fuel-burning equipment to prevent back-drafting.
6. Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection Association (NFPA) the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
7. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
8. Ducted fans must always be vented to the outdoors.
9. Do not use this unit with any solid-state speed control device.
10. TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
11. This unit must be grounded. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
12. Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.
13. When applicable local regulations comprise more restrictive installation and/or certification requirements, the aforementioned requirements prevail on those of this document and the installer agrees to conform to these at his own expense.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE

• Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly in low or medium settings.
• Always turn the hood ON when cooking at high heat or when flambeing food.
• Clean ventilating fans frequently. Grease should not be allowed to accumulate on fans, filters or in exhaust ducts.
• Use proper pan size. Always use cookware appropriate for the size of the surface element.

WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE FOLLOWING*:

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner.
2. BE CAREFUL TO PREVENT BURNS. IF THE FLAMES DO NOT GO OUT IMMEDIATELY, EVACUATE AND CALL THE FIRE DEPARTMENT.
3. NEVER PICK UP A FLAMING PAN — You may be burned.
4. DO NOT USE WATER, including wet dishcloths or towels —This could cause a violent steam explosion.
5. Use an extinguisher ONLY if:
   • You own a Class ABC extinguisher and you know how to operate it.
   • The fire is small and contained in the area where it started.
   • The fire department has been called.
   • You can fight the fire with your back to an exit.
6. Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For indoor use only.
2. For general ventilating use only. Do not use it to exhaust hazardous or explosive materials and vapours.
3. To avoid motor bearing damage and noisy and/or unbalanced impeller, keep drywall spray, construction dust, etc. off the power unit.
4. Install the vent hood in a location away from strong drafts, such as windows, door, and strong HVAC vent for best performance
5. The minimum hood distance above the cooktop must not be less than 25-5/8″. For best capture of cooking impurities, the bottom of the hood should be at a maximum of 29-1/2″ above the cooking surface.
6. Two installers are recommended because of the large size and weight of this unit.
7. To reduce the risk of fire and to properly exhaust air, be sure to duct air outside — Do not exhaust air into spaces within walls or ceilings or into attics, crawl spaces or garages.
8. Because of the high exhausting capacity of this unit, you should make sure enough, air is entering the house to replace exhausted air by opening a window close to or in the kitchen.
9. Always leave safety grills and filters in place. Without these components, operating blowers could catch onto hair, fingers and loose clothing.
10. The vent hood and filters should be cleaned frequently

COMPONENTS

DIMENSION

INSTALLATION PREPARATION

SELECT INSTALLATION TYPE

• Vented Installation
• Non-Vented / Recirculation Installation A 6″ round vent system is needed for installation (not included).
• The hood exhaust opening is 6″ round.
• The vent system can terminate either through the roof or wall.
• To vent through a wall, a 90° elbow is needed.

Rear Discharge
A 90° elbow may be installed immediately above the hood.

WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.

If it is not possible to vent cooking fumes and vapours to the outside, the hood can be used in the non-vented (recirculating) version, fitting a charcoal filter and the deflector (not included, you can decide whether to use according to your installation environment). Fumes and vapours are recycled through the top grille.

Local building codes may require the use of makeup air systems when using ventilation systems greater than the specified CFM of air movement. The specified CFM varies from locale to locale. Consult your HVAC professional for specific requirements in your area.

INSTALLATION PREPARATION

CAUTION

• The vent system must terminate to the outdoors except for non-vented (recirculating) installations.
• Do not terminate the vent system in an attic or other enclosed area.
• Do not use a 4″ laundry-type wall cap (plastic). Only use a metal exterior exhaust vent.
• Use metal vents only. The rigid metal vent is recommended for best performance.
• All vent joints should be taped and sealed with 2″metal foil tape
• The length of the vent system and the number of elbows should be kept to a minimum to provide efficient performance.

For the Most Efficient and Quiet Operation

• Use no more than three 90° elbows.
• Make sure there is a minimum of 24″ of straight vent between the elbows if more than 1 elbow is used.
• Do not install 2 elbows together.
• Use clamps to seal all joints in the vent system.
• Use caulking to seal the exterior wall or roof opening around the cap. The size of the vent should be uniform.

Hood Mounting Screw Installation

1. Determine and mark the centerline on the wall where the hood will be installed.
2. Select a mounting height between a minimum of 25.6” and a suggested maximum of 29.53” above the range to the bottom of the hood. Mark a reference line on the wall.
3. Tape the template in place, aligning the template centerline and bottom of the template with the hood bottom line and with the centerline marked on the wall.

NOTE
Ensure that horizontal lines are level before marking hole locations.

WALL DRILLING AND BRACKET FIXING

As a first step, proceed with the following drawings:

• A vertical line up to the ceiling or up to the upper limit, at the centre of the area in which the hood is to be fitted.
• The cooker hood should be placed 25.6″-29.53″ (horizontal line A) up from the cooking plane for safe and a good effect.
• A horizontal line Bal an X hich abs 8:41 3″ above the cooker top
• A horizontal line C at an X inch above the B.
• A horizontal line D at Y above the cooker hood.

Mark Points

• Mark a point (1) on the horizontal line D, 2.36″ to the vertical reference line.
• Repeat this operation on the other side, checking that the three marks are levelled.
• Mark a point (2) on the horizontal line C, 2.36* to the vertical reference line.
• Repeat this operation on the other side, checking that the three marks are levelled.
• Mark a point (3) on the horizontal line B, 3.15″ to the vertical reference line.
• Repeat this operation on the other side, checking that the three marks are levelled.

Assemble the Lower Chimney Cover

• Slide the Lower Decorative Chimney trim (2.1) over the fan body.
• Ensure that the Decorative trim is pressed down to line up the lower mounting holes (A) Insert 2 short sheet metal screws (12) in the lower holes
  Place Chimney mounting bracket (21) at the top of the Lower Decorative Chimney (2.1), and insert 2 short sheet metal screws (12) into the outermost holes on the bracket at location B

Pre-assemble the Upper Chimney Cover and

• Remove the protective foil from the Upper
• Decorative Chimney (2.2)
• Slide the Upper Decorative Chimney trim (2.2) down between the fan body and the Lower
• Decorative Chimney trim(2.1)
• It should be exposed about 0.25″ above
• The lower Decorative Chimney trim

Hang and Mount the Vent Hood

• Hang the vent hood onto fixing bracket 20
• Level the hood, and insert 2 long screws (10 ) into bracket 21 at level C

Install Duct And Insert Plug

• Install a 6″ duct over the flange on the fan body
• Use 2″ wide metal tape to make an air-tight seal between the duct and the fan body
• Install a clamp to secure the ductwork securely
• Remove Carbon Filters if installed ented applications
• Insert the plug into a properly grounded outlet

IMPORTANT
The vent hood should be lifted and installed by 2 people to prevent injuries and potential damage.

WARNING
Electrical Shock Hazard

• This unit must be grounded. This appliance is equipped with a cord having a grounding wire with a grounding plug.
• The plug must be plugged into an outlet that is properly installed and grounded.
• Do not use an extension cord. If the power supply cord is too short, have a qualified electrician install an outlet near the appliance.

Non-Vented / Recirculation Installation
Recirculation Mode:

• Install Carbon Filters.
• Install a deflector according to your installation environment.

Install Upper Decorative Chimney

• Install Chimney mounting bracket (21) at holes previously marked on level D.
• Slide the upper decorative chimney 2.2 up to the horizontal line D.
• Insert 2 small sheet metal screws into the sides of the bracket to secure the Upper
• Decorative Chimney.

Summary of installation steps

USE
Speed adjustment.

MAINTENANCE

GREASE FILTERS
CLEANING METAL SELF-SUPPORTING GREASE FILTERS

• The filters must be cleaned frequently and can be washed in a dishwasher or a hot detergent solution.
• Depress the latch to remove the filters.
• Avoid bending the filters when washing, and allow the filters to completely dry before reinstalling (The colour of the filter surface may change throughout time but this does not influence to the filter efficiency).
• When reinstalling the filter ensure the release latches are facing down, and are securely in place.

WARNING
Do not operate your cooktop when the filters are not installed into the vent hood.

ACTIVATED CHARCOAL FILTER (RECIRCULATION VERSION)
These filters are not washable cannot be regenerated, and must be replaced approximately every 4 months of operation, or more frequently with heavy usage.

**REPLACING THE ACTIVATED CHARCOAL FILTER

**

• Remove the metal grease filters.
• Remove the saturated activated charcoal filter.
• Install the new filters.
• Replace the metal grease filters.
• The service part number: is 12173000A00481.

LIGHTING LIGHT REPLACEMENT
Replacing the light modules
The entire light module must be replaced. Before changing the light module(s), unplug the appliance or switch off the circuit breaker in the fuse box.

1. Remove the grease filter and carefully remove the 4 screws from each side of the opening (a Phillips head screwdriver will be needed to remove the screws).
2. Lower the control panel at the front by carefully pulling it downwards. You can now access the light module and terminals. Replace the lamp.

DISPOSAL OF OLD ELECTRICAL APPLIANCES
The European directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE), requires that old household electrical appliances must not be disposed of in the normal unsorted municipal waste stream. Old appliances must be collected separately to optimize the recovery and recycling of the materials they contain and reduce the impact on human health and the environment. The crossed-out “wheeled bin” symbol on the product reminds you of your obligation, that when you dispose of the appliance, it must be separately collected. Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliances.

1-YEAR LIMITED WARRANTY

This is the only express warranty for this product and is instead of any other warranty or condition. This product is warranted to be free from defects in material and workmanship for one (1) year from the date of original purchase. During this period, your exclusive remedy is the repair or replacement of this product or any component found to be defective, at our option; however, you are responsible for all costs associated with returning the product to us and our returning the product or component under this warranty to you. If the product or component is no longer available, we will replace it with a similar one of equal or greater value.

This warranty does not cover wear from normal use or operation that does not comply with the instruction manual or damages to the product resulting from accident, alteration, abuse, or misuse. This warranty extends only to the original consumer purchaser or gift recipient. Keep the original sales receipt, as proof of purchase is required to make a warranty claim. This warranty is void if the product is used for other than single-family household use or subjected to any voltage and waveform other than as specified on the label.

Ne excludes all claims for special, incidental, and consequential damages by breach of express or implied warranty. All liability is limited to the amount of the purchase price. Every implied warranty, including any statutory warranty or condition of merchantability or fitness for a particular purpose, is disclaimed except to the extent prohibited by law, in which case such warranty or condition is limited to the duration of this written warranty.This warranty gives you specific legal rights. You may have other legal rights that vary depending on where you live. Some states or provinces do not allow limitations on implied warranties or special, incidental consequential damages, so the foregoing limitations may not apply to you.
Customer Service:
Phone: 1-866-646-4332

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>