ideal lux 8I206 Lika Fi Trimless LED Downlight Instruction Manual

LIKA FI TRIMLESS

8I206 Lika Fi Trimless LED Downlight

THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN
The prolonged observation should not be planned for a distance less than 0,5 m. Place the article with cognition.Depending on the chosen item drill the hole accordingly. Drill the hole into the ceiling.Depending on the thickness of your ceiling, select the appropriate screen-bracket’s hole. Insert the body of the item into the hole, turning it on the side and then bringing it upright. Fix the structure to the ceiling and plaster appropriately.Wire the item and anchor it to the support’s hook.Insert the LEDs structure into the body.
THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.
This product is provided with a light sourceThis product is provided with a light source with efficiency energy class of:with efficiency energy class of:

EAN| Light Source Model| Energy Efficiency Class| Light Source (mA)| Light Source (V)
---|---|---|---|---
8021696206202| LIKA 06W 3000K| F| 700 mA| 6 V DC
8021696267890| LIKA 06W 4000K| F| 700 mA| 6 V DC
8021696206226| LIKA 12W 3000K| F| 700 mA| 15 V DC
8021696267906| LIKA 12W 4000K| F| 700 mA| 15 V DC
8021696206240| LIKA 21W 3000K| F| 600 mA| 30 V DC
8021696267913| LIKA 21W 4000K| F| 600 mA| 30 V DC

LEGENDA ICON

| Replaceable light source by an end-user.
---|---
| Replaceable LED light source by an end- user.
| Replaceable light source by authorized personnel only.
| Upon end of life of the light source, the whole product will be replaced.
| Replaceable control gear by an end-user.
| Replaceable light source by authorized personnel only.
| Upon end of life of the control gear,the whole product will be replaced.

REV 07/01/19

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.596- 1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor Or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wail plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Atways tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire s0 that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Abways observe the minimum distance between the lamp and the surface being fit, as shown in the icon. The lamp can cause a fire i the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety quaranteed by the main insulation and an additional protective conductor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing not necessary.
23. Class lll Electrical safety quaranteed by very low power supply (less than 50 Voit). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against soéd objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically faling water drops.
33. Protected against water drops falling with a maximum angie of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com
Via delle Industrie, 8/D
30036 Santa Maria di Sala (Venezia)
8.00 – 12.00 / 13.30 – 17.00

Documents / Resources

| ideal lux 8I206 Lika Fi Trimless LED Downlight [pdf] Instruction Manual
8I206, 267890, 206226, 267906, 206240, 267913, 8I206 Lika Fi Trimless LED Downlight, Lika Fi Trimless LED Downlight, Trimless LED Downlight, LED Downlight, Downlight
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>