eyesound Jellyfish Lamp Bluetooth Speaker Instructions

Jellyfish Lamp Bluetooth Speaker
Instructions

 The function of the Key host

1. After powering up, press Product startup (enter light pattern), light pattern: Water pump to start working, the light frequency automatic conversion in 8 seconds once lights: red- red/green- green- green and blue- red, green and blue-red and green-red, green and blue-red and blue- red, green and blue-green blue – red, green and blue, loop transformation (light breath when changing the effect of the lamp), don’t play the sound.
   1.1 In the light pattern
   Press or , Light change lighter and darker (when maximum or minimum, there will be a long tone hint)
   Press or Lights stop change， at the current color fixed.
   Press or again, When the lights change to the previous or next light (again fixed), the first set of red or the last set of red, green, and blue, then press or Enter full light automatic loop (voice prompt loop play）.
   1.2 In light pattern, then press , The product enters the white noise playback mode (without voice prompt, directly insert the built-in sound (remember the sound when turning off the audio mode last time, single sound cycle), and retain the Settings in the light pattern for the water pump and light.

2. 1In white noise mode
   Press or , Increase or decrease the sound (the light remains the same, when the sound is maximum or minimum, there will be a long tone hint).
   Press or Enter the previous song or the next song (lights unchanged) Press or again, Enter white noise mode with automatic loop play (voice prompt loop play), each audio play for 60 seconds, and wait for 3 seconds to enter the next song.

3. white noise mode, press again, and The product enters Bluetooth mode (voice prompt “Bluetooth mode”, Automatically matches Bluetooth, and the voice prompt “Bluetooth is connected” is displayed.)In Bluetooth mode, the water pump and lights are set in the light pattern, and white noise is prohibited.
   3.1 In Bluetooth mode, press or Increase or decrease the sound (the light remains the same when the sound is maximum or minimum, there will be a long tone hint). Press or Enter the previous song or the next song (lights remain).

4. In Bluetooth mode, press again , go back to the light pattern, and loop around. Long press 2 seconds to power off.
   Note: The red font of the voice prompt is a female English voice. The above sound, sound size, light brightness, and cyclic play mode should be in power-off memory mode, and the corresponding Settings before power off should be retained after power on Lamp brightness points 6 gears: 5 V/4.5 V/4.0 V/3.5 V/3.0 V/2.5 V There are 32 levels of sound

The key function of the remote control

1. Press “ ” to control the switch, press” on “, and then press “off”

2. Press “ ” to enter the white noise mode

3. Press “ ” to enter Bluetooth mode. If the product is already in Bluetooth mode and connected to the mobile phone, the product will do nothing! If the product is in Bluetooth mode and is not connected to the mobile phone, the voice will prompt “Bluetooth mode”.

4. Press , to control the swimming speed of jellyfish, press the pump to turn on for 9 seconds, stop for 2 seconds, then press the pump to turn on for 5 seconds, stop for 2 seconds, and cycle in two modes.\

5. Press “ ” to control the sound reduction. Press one to go down one level, and the host prompts a long tone when the minimum is small

6. Press “ ” to increase the sound. Press to raise the sound level. When the maximum is reached, the host will make a long sound.

7. Press “ ” to control the previous song, control white noise or mobile phone music, and enter the previous song. Select play mode in cyclic mode (refer to host button function)

8. Press “ ” to control pause, control white noise or mobile phone music, and enter a pause.

9. Press “ ” to control the next song, control the white noise or mobile phone music, and proceed to the next song. Select play mode in cyclic mode (refer to host button function).
   The five buttons with the yellow bottom are invalid in the default mode of the product.

10. Press “ ” to control timing, press the voice prompt” timing success “30 minutes after the product timing, power off, and press the voice prompt” timing cancellation”

11. Press “ ” to control timing, and press the voice prompt” timing success “. After 60 minutes of product timing, power off, and press the voice prompt “timing cancellation” again.

12. Press “ ” to control timing, and press the voice prompt” timing success “. After 120 minutes of product timing, power off, and press the voice prompt “timing cancellation” again.

13. Press “ ” to control the red light. Press this button and the red light will be steady on

14. Press “ ” to control the green light. Press this button and the green light will be steady on

15. Press “ ” to control the blue light. Press this button and the blue light will be steady on

16. Press “ ” to control red/green lights. Press this button, and red and green lights are always on

17. Press “ ” to control red/blue lights. Press this button, and red and blue lights will be on

18. Press “ ” to control green/blue light. Press this button, and green and blue lights will be on

19. Press “ ” to control the red/green/blue light. Press this button and the lights of the three colors will be steady on

20. Press “ ” to control the light brightness. Press this button to brighten the light, and the host will give a long tone when the maximum is reached.

21. Press “ ” to control the light brightness. Press this button to reduce the light, and the host will give a long tone when the minimum is small.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
RF Exposure Information
The device has been evaluated to meet the general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>