LG KBA2/MSA2 Wireless Keyboard and Mouse User Manual
- June 4, 2024
- LG
Table of Contents
KBA2/MSA2 Wireless Keyboard and Mouse
User Manual
▶ Insert and replace the wireless keyboard/mouse battery
Insert or replace the battery in the following ways using the wireless
keyboard and mouse.
Batteries are provided when purchasing products, and AAA type 1.5 V battery is
used.
[Notes]
- The power button is not provided on the wireless keyboard.
- A low battery can cause a wireless keyboard/mouse to stop operation.(Please change the battery.)
- Do not use it close to other devices such as microwaves, wireless routers, etc. as interference may occur with these devices that use frequencies in the 2.4 GHz band.
- If you are not using your PC for a long time, turn off the power button of the mouse.
Inserting and replacing the wireless keyboard battery
-
Remove the battery cover by pushing it in the direction of the arrow.
-
Insert or replace the two batteries in the +/- direction and close the battery cover in the direction of the arrow.
-
Push it until it makes a “click” sound in the direction of the arrow.
-
If the battery is consumed and replacement is required, the battery replacement notification LED is turned on.
When the battery is completely exhausted, the LED will no longer turn on.
Inserting and replacing the wireless mouse battery
-
Remove the battery cover in the direction of the arrow.
-
Insert the two batteries in the +/- direction and close the battery cover.
-
Turn on the mouse as shown in the picture.
When the power is on, the red LED (battery status indicator) in the center of the mouse turns on for 5 seconds. -
If the battery is exhausted and needs to be replaced, the battery status indicator will continue to blink.
When the battery is completely exhausted, the LED will no longer turn on. -
Replace the battery in the reverse order of how to insert the battery.
Connecting and using the receiver
The wireless keyboard and mouse are synchronized when shipping the product, and it can be used immediately without any additional settings.
<Example: Inserting a wireless
receiver>
Caution
When connecting with other products, compatibility issues may occur with some
products. LG Electronics does not guarantee compatibility with all peripheral
devices.
Use between 0℃ and 40℃.There is a risk of product damage, errors, or explosion
if used and stored at too low or too high temperatures.
Install in a safe place where there is no risk of falling.
Falling may damage the product or cause personal injury.
Be careful not to spill liquids such as water, coffee, or juice on the mouse
as it may cause defects or malfunction.
Keep the product away from hot products (heaters, etc.). The product may be
deformed or there is a risk of fire.
When not using the product for a long time, turn off the product to prevent
unnecessary battery consumption.
Do not disassemble or modify the product. Even during the warranty period, it
is not subject to free maintenance.
For users who have transplanted a medical device, please use it after
consulting a doctor.
Avoid exposure to direct sunlight in places such as inside a closed car. The
shape of the product may be deformed due to an increase in temperature, or
there is a risk of fire.
Do not use it for any purpose other than the mouse function.
Risk of fire or explosion if the battery is replaced by an incorrect type Keep
out of reach of children.
The nano receiver (dongle) provided with the mouse is set to work only with
the wireless mouse you purchased.
Please note that it does not work with other models and the same model of
another serial number.
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. the equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference does not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution : Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
Radiation Exposure Statement:
The product complies with the FCC portable RF exposure limit set forth for an
uncontrolled environment and is safe for intended operation as described in
this manual. Further RF exposure reduction can be achieved if the product can
be kept as far as possible from the user body or set the device to lower
output power if such a function is available.
Industry Canada statement:
This device complies with ISED’s license-exempt RSS. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radiation Exposure Statement:
The product complies with the Canada portable RF exposure limit set forth for
an uncontrolled environment and is safe for intended operation as described in
this manual. Further RF exposure reduction can be achieved if the product can
be kept as far as possible from the user body or set the device to lower
output power if such a function is available.