BestFriendBands B09TXK1SN1 Friendship Bracelet Making Kit Instruction Manual
- May 15, 2024
- BestFriendBands
Table of Contents
BestFriendBands B09TXK1SN1 Friendship Bracelet Making Kit
Product Information
Specifications:
- Product Name: Bracelet Loom
- Material: Plastic
- Color: Assorted
- Dimensions: 10 inches x 5 inches x 1 inch
Product Usage Instructions
Getting Started:
- The center ring indicates the pattern you will be making.
- Hook the string into the loom where there are notches.
- The petals indicate the colors of string to use.
- Follow the colors on the loom as a guide or create your own combinations.
Setting Up the Loom:
- Cut lengths of string according to the colors shown on the loom.
- Tie the ends of the strings together and divide them into two groups.
- Put the groups around a pencil and tie them together close to the pencil to create a loop for your wrist.
- Place the loop in the center of the loom and hook each strand into the matching colored petal notch.
Creating Your Bracelet:
- Unhook one strand at a time and rehook it in another notch to create your bracelet.
- Follow the pattern by moving strings between notches as indicated on the loom.
Tips and Tricks:
- Keep your strings tight by pulling them away from each other before switching middle strings.
- Untangle loose strings often to avoid knots.
Finishing:
- When your bracelet is long enough, unhook all strings from notches and double knot them after smoothing in one direction.
- Trim the ends of the strings neatly to finish off your bracelet.
FAQ
- Q: How do I add beads to my bracelet?
A: You can add beads to the middle strings to place along the sides of your bracelet. You can also add beads to the end of the bracelet to create a fancy tassel.
OVERVIEW
You can make a bracelet using the colors shown on the loom or create your own color combinations.Simply use the colors on the loom as a guide.For example,the loom shown here has red and blue stripes.To make pink and green stripes,just put pink string where you see red petals and put green string where you see blue petals.
HOW TO USE
GET SET!
Now that you know how the loom works,Let’s set it up with string! Start
with the horizontal stripe pattern. ALL THE PATTERNS WILL BE SET UP IN THE
SAME WAY.
Cut a 20”length of string(2 lengths od the ruler on the right)for each of the
petals on the top and bottom on the loom in the corresponding color4.0C”utl
engths for the 2 middle sFtori negxsa.mple,for the horizontal stripes cut 8
blue strings and 7 red strings all 20”long. Cut 2 yellow strings each 40”long
.
Place the loop in the center of the loom .Now pull out each strand and hook it
into the notch of the matching colored petal.
GO!
To create your bracelet you will need to unhook one strand at a time and
rehook it in another notch.
EVERY PATTERN IS MADE THE SAME WAY!
- Move the string from the START arrow into the empty notch directly below it.
- Now move the next string on the bottom up to the empty notch on top.
- Now move the next top string to the empty notch on the bottom.
- Continue moving the strings in this way:move the bottom strings up and then move the top strings down into the empty notches below.
- Now all of the red strings should be on the top and all the blue strings should be on the bottom.
- Switch the positions of the yellow strings.(The right string will move into the left notch and the left string will move into the right notch.)
TIPS AND TRICKS
keep your strings nice and tight! Before you switch the middle strings in Step
6, pull them away from each other.Pull until you see the top and bottom
strings all touch at the center point.
FINISH! When your bracelet is long enough, unhook all of the strings from the notches. Smooth the strands in the same direction, making sure they are not tangled, and double knot. Trim the ends of the string in a neat tassel and trim the strings close to the loop on the other side. Pass the knot through the loop to wear your bracelet!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>