CONDO MOUNTS TVAT8164 Advanced Tilt TV Wall Mount for Steel Stud Instruction Manual
- June 17, 2024
- CONDO MOUNTS
Table of Contents
CONDO MOUNTS TVAT8164 Advanced Tilt TV Wall Mount for Steel Stud
Product Information
Specifications:
- TV Weight Limit:
- Drywall/Metal Stud Installation: 120lbs
- Single Stud Mounting Option: 100lbs
- Drywall Mounting Option: 80lbs
- Drill Bit Size: 1/2 in (13 mm)
- Wall Anchor Size: 1/4 in
Product Usage Instructions
Drywall/Metal Stud Installation:
- Locate the stud and mark the centre of the studs on the wall with a pencil.
- Drill four holes to a depth of 1 in. (26 mm) using a 1/2 in. (13 mm) diameter drill bit.
- Hold the plastic straps by the end and pull towards the wall. Ratchet cap along straps with other.
Single Stud Mounting Option:
- Locate studs and mark the centre of the studs on the wall with a pencil.
- Place the wall plate at your desired height and position over your studs. Level the wall plate and mark the hole on the wall.
- Drill four holes to a depth of 1 in. (26 mm) using a 1/2 in. (13 mm) diameter drill bit.
- Install the wall plate using four screws and washers. Tighten all screws only until they are pulled. Once the wall mount is secured, proceed to the main instructions to mount the TV.
Drywall Mounting Option:
- Insert wall anchors by folding metal channels until it is into the drilled hole.
- Angle the drill at a 65-degree angle with the wall anchor.
FAQ
-
Q: Can I mount a TV heavier than the specified weight limits?
A: No, for safety reasons, do not exceed the weight limits specified for each mounting option. -
Q: What should I do if I don’t understand the installation instructions?
A: If you have any doubts or don’t understand the instructions, please contact the manufacturer for assistance to avoid any potential personal injuries or property damage. -
Q: Where can I find a video tutorial for this DIY project?
A: You can watch a video tutorial at www.condomounts.com/metalstud for a visual guide on how to install the mount.
Safety Instruction
Read the entire instruction manual before you start installation and assembly. If you have any questions regarding any of the instructions or warnings, please contact your local distributor for assistance.
CAUTION:
Use with products heavier than the rated weights indicated may result in
instability causing possible injury.
- Please closely follow the assembly instructions. Improper installation may result in damage or serious personal injury.
- Safety gear and proper tools must be used. This product should only be installed by professionals.
- This product is designed to be installed on solid concrete walls, masonry walls or wood stud walls.
- Make sure that the supporting surface will safely support the combined weight of the equipment and all attached hardware and components.
- Use the mounting screws provided and DO NOT OVER-TIGHTEN mounting screws.
- This product contains small items that could be a choking hazard if swallowed. Keep these items away from children.
- This product is intended for indoor use only. Using this product outdoors could lead to product failure and personal injury.
IMPORTANT:
Ensure that you have received all parts according to the component checklist
prior to installation. If any parts are missing or faulty, contact your place
of purchase for a replacement.
MAINTENANCE:
Check that the product is secure and safe to use at regular intervals (at
least every three months).
What’s In The Box
Hardware List
Tools
Installation Instruction
Drywall/Metal Stud Installation
- TV must not weigh more than 120lbs
- Locate studs and mark the centre of studs on the wall with a pencil
- Place the wall plate at your desired height and position it over your studs. Level the wall plate and mark the hole on the wall
- Drill four holes to a depth of 1 in. (26 mm), using a 1/2 in. (13 mm.) diameter drill bit
- Insert wall anchors by folding metal channels until it is flat with the plastic straps. Slide the metal channel into the drilled hole.
- For narrow stud
- Hold the plastic straps by the end and pull towards you until the metal channel is flush behind the wall.
- Hold the ends of the straps together between the thumb & forefinger and pull toward you untill the channel rests behind the wall. Ratchet the cap along the straps with another hand until the flange of the cap is flush with the wall.
- Bend the straps side to side until they snap off level with the flange of the cap.
- Install the wall plate using four screws Q and washers R. Tighten all screws Q only until they are pulled firmly against the wall plate. Once the wall mount is secured, proceed to the main instructions to mount the TV.
Single Stud Mounting Option
Drywall Mounting Option
SAFETY CAUTION
CAUTION:
Avoid potential personal injuries and property damage!
-
The wall must be capable of supporting five times the weight of the TV and mount combined.
-
The manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
-
If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of this product, contact manufacturer Customer Service or call a qualified contractor.
• If the back side of the wall is unfinished, the drywall must be installed to a minimum of one stud left and right of the stud(s) being used to install the mount. -
Drywall must be a minimum of 13 mm (1/2 in.) thick on each side of the studs, and a minimum clearance of 48 mm (1 7/8 in.) behind the wall is required.
-
Pilot holes MUST be drilled to a depth of 25 mm (1 in.), using a 13 mm (1/2 in.) diameter drill bit.
Want to watch a video that shows how easy this DIY project will be?
Watch it now at:
www.condomounts.com/metalstud.