CommSin RRG-100 Hand Function Rehabilitation Robot Gloves User Manual

REHABILITATION ROBOT GLOVE

RRG-100 Hand Function Rehabilitation Robot Gloves

For hand flexibility training Promoting blood circulation and hand function recovery Relieving Hand stiff problem

Please read the instructions carefully before using the product

Product Description

This robot glove for hand function rehabilitation combines neuroscience and flexible robotics technology, and use the flexible pneumatic bionic glove as the power source. Through hand training, it promotes the recovery of hand flexibility of user from three levels of nerves, brain and muscles.
This product adopts a large flow positive and negative pressure air pump to independently control the solenoid valves of five fingers, gas sports gloves that fit the hand, and the hand stretching motion can be controlled independently through the humanized interface.
A variety of training methods of the product can meet the needs of different groups of people, and it has advanced mirroring function.
Note: New designed soft mode is suitable for people with serious hand injuries.

Main Features

1. Large-capacity rechargeable lithium battery (11.1V, 2600mAH). When charging the battery, the system automatically switches to the direct power supply mode, which can bring a greater training experience.
   It is recommended to use the power supply for daily use, and it can be powered by the battery when you are outside, , easy to carry and use. The host is equipped with a power switch, which is energy-saving and environmentally friendly.

2. Positive and negative air pumps with large flow rate of gas (flow rate ≥ 5 liters per minute), two-position three-way solenoid valve for independent training of five fingers, and strong exercise. The exquisite and reasonable design can stabilize the heat generated by the product in a constant range and increase the service life of the product.

3. Touch button and LED display, easy to operate, clear at a glance.

4. It has the function of free selection of five fingers for independent training, which can realize the selected’s fingers simultaneous training and sequential training in turn.

5. New designed soft mode can realize soft training, and the stretching range is controllable, which is suitable for people with serious hand injuries.

6. The mirror hand strap, it can realize the coordinated training of both hands.

7. The time and strength of finger stretching and clenching can be adjusted independently.

8. The product can remember the personalized settings of this training, and can be used directly when the machine is turned on next time. In addition, the product has a system reset button.

9. The product design is beautiful and high-grade, using ABS, rubber PE, transparent PC and other materials.

Product Composition

The host

1. Touch button and icon display area
2. Power supply and charging port
3. Power switch
4. Rehabilitation glove access port

Panel introduction

1. Three mode: Automatic mode, Mirror mode, Soft mode.
2. Five-grid power display, if you feel that the training is not enough or the working status is not normal, you need to charge it in time, and it will automatically switch to the power supply for direct power supply when charging.
3. Time display, showing the use time of a single training session, the maximum use time of a single session is 20 minutes.
4. Movement level display of hand stretching and clenching.
5. Save/ reset function touch button, touch the corresponding option of this button will light up.
6. Automatic mode touch button, the selected ’s fingers take turns training in turn.
7. All modes touch button, the selected ’s finger training together
8. Pause/Start function touch button, timing display stops or continues.
9. Hand stretch/clench motion level adjustment touch button.
10. Mode selection touch button, lightly touch the button to switch between automatic and mirror mode, long press the button to switch to soft mode.
11. The host standby / open function touch button.
12. Select/Cancel the function touch key of the moving finger.
13. Red light charging display. The red light lit means charging, and the lantern extinguishes means that the charging is completed. Both the product’s power supply has this function in the state of the switch.

Gloves to wear

Precautions for wearing gloves

1. Before using, select the right size and specifications to avoid affecting the effect of use.
2. Can’t open your fingers because of the muscle tension and stiffness and difficult to open it. You can knead and massage the affected limb for 5 minutes.
   ※It is recommended to wear gloves when sitting or lying.

Step 1: Put the affected fingers into the gloves in turn.Note: Fingers need to reach the top of the glove finger Step 2: Tighten the wrist and magic sticker.Note: Pull the inner ring of the glove finger as much as possible backwards Step 3: The fixed auxiliary fixed zone shown in the figureNote: Put it correctly, there is no gap in the wrist when you fist

Mirror Hand Strap

Instructions

1. In the mirror mode, presses the mirror image button inside the strap with a finger, and the other gloved hand will hold it tightly at the same time. Release the button, and the hand will extend at the same time. Press and release the button multiple times continuously to achieve continuous clenching and stretching training.
2. If the product cannot work properly, it is recommended to try it again after full charging. Mirror hand strap charging method: tear the magic sticker in front of the hand strap, remove the internal accessories, insert the USB charging cable with a 5V charger interface (the charging line (Type-C interface) of the mobile phone or mobile device), the red Indicates charging, and red lights are extinguished after full. Press the key green light flash to indicate that the mirror function can be used normally.

Rehabilitation Glove

1. Connect the rehabilitation glove to the host, put on one hand that needs to be trained on a glove.

2. Open the host power, the time indicator is displayed 00:00, prepare for training, the battery status displays the number of grids according to the actual power volume. Touch the button to start training. After the training is completed, touch the button   again, wait for 1 second to let the host release the gas in the gloves. After the time indicator is destroyed, then the gloves are unbuttoned.
   Note: Product settings protection mechanism can be used for up to 20 minutes.
   If you start the next training again, when the power is turned on, long press the key to start training and time update.
   If it is not used for more than six hours, the host power should be closed.

3. During the training process of fingers, touch the key and system pause.

4. Touch the key , the product will switch in the automatic mode ( ****) and mirror mode ( ), long press bottom , switch to soft mode, ( ).

5. By default, the touch key  will increase or reduce the level of motion of grip and stretching at the same time (Note: the indicator light will display the eight -level adjustment accordingly)
   If the level of grip and extension is required separately, the method is as follows:
   Long press button , the grip level display lights will flashes continuously.
   At this time, the key will only adjust the grade level. After the adjustment, the long press button ,the display light stops flashing. Similarly, long press **** key , extended display lights will flashes continuously, the adjustment method is the same as grip.

6. In all modes, touch the 6 key , and the selected’s fingers extend/grip at the same time.

7. Only in the automatic mode, touch the 7 key , the players’ fingers take turns training in turn.

8. Touch the 5 key , execute the saving function, the lights on the player’s finger flashes once, and the current parameter preservation is successful.
   Press 5 key to execute the reset function. All the lights on all fingers flickered three times, and the system returned to the factory settings.

9. Touch the buttons on the fingers to select or not choose the finger of training.
   The corresponding light indicates that the finger training is selected.
   Note: The picture shown in the product display is a schematic diagram of the finger position facing the right hand.
   You must choose at least one finger for training, and the light least one finger is on.

Product Specification

What in the box

*Special Note
Product specifications, appearance, color, function and product accessories are subject to change without prior notice, please refer to the actual product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>